continuous emissions monitoring Equipment in Barbados

Served | Office inNear
76 Results found
  • Category: Air & Climate ×

  • Subcategory: Air Monitoring ×

  • Keyword: continuous emissions monitoring ×

  • Location: Latin America ×

  • Location: Barbados ×

Model SM8200 - SO2/NO In Situ Multi-Gas Analyzer

by Teledyne Monitor Labs, Inc.     based in Englewood, COLORADO (USA)

The transceiver houses the light source, spectrometer, multi-gas photodiode array detector system and various focusing optics for outstanding performance over a significant range of operating conditions.  The transceiver is constructed of a rugged cast aluminum housing which is latch-detachable from the probe assembly for easy removal and ...

PCME - Model STACK 980 - Particulate Continuous Emission Monitor

by PCME Ltd     based in St Ives, UNITED KINGDOM

The PCME STACK 980 is an approved Particulate Continuous Emission Monitor suited to industrial applications in stacks after bag filters, cartridge filters, cyclones and process driers. The instrument combines the latest regulatory approvals (MCERTS Performance Standards for Automated Dust Arrestment-Plant Monitors, version 1 (August 2010), class 2 ...

Model Dilution Series - Continuous Emissions Monitoring Systems

by Monitoring Solutions     based in Indianapolis, INDIANA (USA)

A Dilution CEMS offers the lowest maintenance of any CEMS by it's elimination of sample conditioners and pumps. Compressed air is used to 'power' the Dilution CEMS. It is sent up the stack where it is mixed with the stack gas at a 100:1 ratio (typ.). The sample is then pushed down to the analyzers. Besides the stack gas being diluted, the moisture ...

Teledyne - Model ML675 - Dilution-Extractive System

by Teledyne Monitor Labs, Inc.     based in Englewood, COLORADO (USA)

The Teledyne ML675 dilution-extractive system can be used in 40CFR75, 40CFR60, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.

IntelliCEMS - Model IC Series - Straight Extraction Or Dilution Extraction Systems

by Cemtrex Inc.     based in Farmingdale, NEW YORK (USA)

The IC Series IntelliCEMSTM include straight extraction or dilution extraction systems complete with sample probes, heated sample bundles, sampling systems, analyzers, and Data Acquisition Systems (DAS). Our CEMS are pre-engineered and packaged to measure a wide range of gases and pollutants for compliance with state and federal EPA regulations ...

StackGuard - Dust Emission Measuring System

by Sigrist-Photometer AG     based in Ennetbürgen, SWITZERLAND

The StackGuard continuously monitors the scatted light intensity of an extracted, withdrawn sample of gas. The laser light source minimized stray light and improves sensitivity to the µg/m³ level, the filtered purge air prevents from window soiling. A calibration check is performed by means of a checking rod. The sample air is led out ...

Lowe Engineering - Gas Sample / Detection Analysis

by Lowe Engineering Limited     based in Leeds, UNITED KINGDOM

The following extract from Perry's Chemical Engineers' Handbook, will give some insight into the sampling and analysis of Hydrocarbons.

Model BKS-3000 - Continuous Emission Monitoring Systems

by Beijing Care Corporation Ltd.     based in Beijing, CHINA

BKS-3000 Continuous Emission Monitoring Systems (CEMS) is a packaged system in which a sample of gas is continuously drawn from the process point, which is applied for monitoring various industrial sources of air pollutants. Gas concentrations such as SO2, NOx, O2 are on-line continuously detected, the temperature, pressure and flow rate of the ...

MRU - Model SWG 300-1 - Emission Monitoring Systems

by MRU Instruments, Inc.     based in Houston, TEXAS (USA)

CEMS based on cold&dry extractive technolgy. Using complete gas sample conditioning system (heated probe filter, heated sampling line, gas cooler etc) and NDIR or GFCIR measurement for up to 6 flue gas components (O2, CO, CO2 , NO, SO2, HC). Also suitable for installations in hazardous area zone 2 (class 1, div 2), with manufacturer ...

Model AL4021 Series - Continuous Formaldehyde in Air and Water Monitor

by AERO-LASER GmbH     based in Garmisch-Partenkirchen, GERMANY

Automated HCHO analyzer for very low concentrations.The AL4021 is a completely automated and continuously working formaldehyde (HCHO) analyzer for gaseous and liquid samples based on the Hantzsch reaction, which is sensitive to very low concentrations of HCHO (ppbV for gaseous samples and µg/l for liquid samples). All functions of the AL4021 ...

Need help finding the right suppliers?

Let the XPRTs do the work for you