continuous emissions monitoring Equipment in District of Columbia

Served | Office inNear
108 Results found
  • Category: Air & Climate ×

  • Subcategory: Air Monitoring ×

  • Keyword: continuous emissions monitoring ×

  • Location: USA ×

  • Location: District of Columbia ×

Lowe Engineering - Gas Sample / Detection Analysis

by Lowe Engineering Limited     based in Leeds, UNITED KINGDOM

The following extract from Perry's Chemical Engineers' Handbook, will give some insight into the sampling and analysis of Hydrocarbons.

Teledyne - Model ML675 - Dilution-Extractive System

by Teledyne Monitor Labs, Inc.     based in Englewood, COLORADO (USA)

The Teledyne ML675 dilution-extractive system can be used in 40CFR75, 40CFR60, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.

IntelliCEMS - Model IC Series - Straight Extraction Or Dilution Extraction Systems

by Cemtrex Inc.     based in Farmingdale, NEW YORK (USA)

The IC Series IntelliCEMSTM include straight extraction or dilution extraction systems complete with sample probes, heated sample bundles, sampling systems, analyzers, and Data Acquisition Systems (DAS). Our CEMS are pre-engineered and packaged to measure a wide range of gases and pollutants for compliance with state and federal EPA regulations ...

MRU - Model OMS 420-HT - Combustion Optimization System

by MRU Instruments, Inc.     based in Houston, TEXAS (USA)

High temperature probe. In-situ probe with heated ZrO2 sensor for wet O2 analysis up to 3090°F (1700°C), using ejector for sample aspiration through Kanthal or Ceramic tube and remotely mounted transmitter.

Model Dilution Series - Continuous Emissions Monitoring Systems

by Monitoring Solutions     based in Indianapolis, INDIANA (USA)

A Dilution CEMS offers the lowest maintenance of any CEMS by it's elimination of sample conditioners and pumps. Compressed air is used to 'power' the Dilution CEMS. It is sent up the stack where it is mixed with the stack gas at a 100:1 ratio (typ.). The sample is then pushed down to the analyzers. Besides the stack gas being diluted, the moisture ...

VIG Industries - Model System 2 - Continuous Emissions Monitoring ( CEM ) Systems

by VIG Industries     based in Anaheim, CALIFORNIA (USA)

This CEM system includes a Model 200/1 Methane / Non methane FID Hydrocarbon Analyzer, a Model 300/2 CO / CO2 NDIR Analyzer, custom built 14 point sequencer, combustion & zero air generator, hydrogen generator, external sample pump, approximately 5000 feet of Teflon sample tubing, monitoring point vaults mounted in the concrete, monitoring ...

VIG Industries - Model System 6 - Continuous Emissions Monitoring ( CEM ) Systems

by VIG Industries     based in Anaheim, CALIFORNIA (USA)

VIG Industries has been working with a major paint booth manufacturer to design systems to measure their abatement efficiency. These systems work on a new patented technology not using standard carbon, which can be regenerated by using warm air rather than steam.

Model BKS-3000 - Continuous Emission Monitoring Systems

by Beijing Care Corporation Ltd.     based in Beijing, CHINA

BKS-3000 Continuous Emission Monitoring Systems (CEMS) is a packaged system in which a sample of gas is continuously drawn from the process point, which is applied for monitoring various industrial sources of air pollutants. Gas concentrations such as SO2, NOx, O2 are on-line continuously detected, the temperature, pressure and flow rate of the ...

ULTRAMAT - Model 6 - Continuous Gas Analyzers For IR Active Component

by Siemens Industry, Inc. - Process Analytics     based in Houston, TEXAS (USA)

Most frequently used for demanding applications, the ULTRAMAT 6 must meet high standards with regard to reliability and measuring quality. This is guaranteed by modern electronics, ease of operation and a physical element that is adapted to the measuring task.

CEMSentry - Model 3000 - Continuous Emission Monitoring System

by CEM Service Group, Inc.     based in Bedminster, PENNSYLVANIA (USA)

TheCEMSentry™3000 is a state-of-the-art, Continuous Emissions Monitoring System (CEMS) that utilizes a variety of analytical techniques specific to the gases to be monitored and specialized sample transport and conditioning equipment designed for each specific application. The CEMSentry™3000 CEMS is

Need help finding the right suppliers?

Let the XPRTs do the work for you