opacity monitoring Equipment in New Mexico

Serving New Mexico | Near New Mexico
14 Results found
  • Category: Air & Climate ×

  • Subcategory: Air Monitoring ×

  • Keyword: opacity monitoring ×

  • Location: USA ×

  • Location: New Mexico ×

Integrated Emissions & Monitoring Systems

by Procal - Parker Hannifin Corp     based in Peterborough, UNITED KINGDOM

To comply with the specification of many CEMS it is necessary to monitor and report, not only the gas emissions, but also properties such as particulates or opacity. In addition to generating reports in formats acceptable to environmental agencies, it is often necessary to monitor Oxygen and Velocity. The Procal solution enables this data to be ...

MONITOR TECH - Model MT100 - Data Acquisition System

by Monitor Tech Corporation LLC     based in Columbus, OHIO (USA)

MonitorTech delivers everything you need from our unique probe to our Data Acquisition System and reports.ALL EPA REQUIRED EMISSION GASES NOx (NO + NO2), CO, O2s wet/dry (moisture), SO2, Hcl, NH3, CO2,Opacity, Flow, CH4, H2S, H2, C6H14, C3H4, Cl, HCl, HCN etc.

Opsis - Opacity Meter

by Opsis AB     based in Furulund, SWEDEN

Opacity metering instruments are supplied and integrated in the CEM system.

Model EMS611 - Dust Monitor

by Environmental Monitor Service, Inc.     based in Yalesville, CONNECTICUT (USA)

The EMS611 provides continuous, low maintenance, precision measurement of dust (mg/m3(N), Optical Density and Opacity. It is designed for monitoring visible smoke and particulate concentrations in the exhaust gas of industrial combustion or air filtration processes. The EMS611 dust monitor utilizes dual beam measurement and the highest quality ...

OFS - Model 2000-W - Emissions/Air Flow Sensor

by Optical Scientific Inc. (OSi)     based in Gaithersburg, MARYLAND (USA)

OSi's patented Optical Flow Sensor (OFS) makes driftfree measurements across the entire stack, duct or pipe diameter and calculates a true average flow reading. The OFS 2000-W model is equipped with Automatic Gain Control (AGC) to compensate for variations in opacity caused by particulate matter or moisture carried in the stack flow. The OFS uses ...

Teledyne - Model ML675 - Dilution-Extractive System

by Teledyne Monitor Labs, Inc.     based in Englewood, COLORADO (USA)

The Teledyne ML675 dilution-extractive system can be used in 40CFR75, 40CFR60, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.

Model 445 - Compliance Opacity Monitoring System

by Thermo Scientific - Air Quality Instruments     based in Franklin, MASSACHUSETTS (USA)

The Model 445 is a robust dust concentration monitor for a broad range of applications. The instrument features automatic check cycles, built-in 4 point linearity check and contamination correction.

IntelliCEMS - Model IC Series - Straight Extraction Or Dilution Extraction Systems

by Cemtrex Inc.     based in Farmingdale, NEW YORK (USA)

The IC Series IntelliCEMSTM include straight extraction or dilution extraction systems complete with sample probes, heated sample bundles, sampling systems, analyzers, and Data Acquisition Systems (DAS). Our CEMS are pre-engineered and packaged to measure a wide range of gases and pollutants for compliance with state and federal EPA regulations ...

Aerodyne - CAPS NO2 Monitor

by Aerodyne Research, Inc.     based in Billerica, MASSACHUSETTS (USA)

The CAPS NO2 monitor provides a direct absorption measurement of nitrogen dioxide at 450 nm in the blue region of the electromagnetic spectrum. Unlike standard chemiluminescence-based monitors, these instruments require no conversion of NO2 to another species and thus are not sensitive to other nitro-containing species.

CEMSentry - Model 3000 - Continuous Emission Monitoring System

by CEM Service Group, Inc.     based in Bedminster, PENNSYLVANIA (USA)

TheCEMSentry™3000 is a state-of-the-art, Continuous Emissions Monitoring System (CEMS) that utilizes a variety of analytical techniques specific to the gases to be monitored and specialized sample transport and conditioning equipment designed for each specific application. The CEMSentry™3000 CEMS is

Need help finding the right suppliers?

Let the XPRTs do the work for you