dust emissions Equipment in Indiana

Serving Indiana | Near Indiana
86 Results found
  • Category: Air & Climate ×

  • Subcategory: Dust Control ×

  • Keyword: dust emissions ×

  • Location: USA ×

  • Location: Indiana ×

Land - Model 4500 MkIII - Opacity and Dust Emissions Compliance Monitor

by AMETEK Land     based in Dronfield, UNITED KINGDOM

The Land Model 4500 MkIII has reset the industry standard on compliance opacity and dust concentration measurement. Combining the unique features of three patented technologies, the 4500 MkIII achieves the highest available specification for the principal performance parameters, as defined by the internationally recognized ASTM Standard D 6216-07.

Land - Model 4200 - Non-Compliance Dust Emissions Monitor

by AMETEK Land     based in Dronfield, UNITED KINGDOM

The Model 4200 is a compact smoke, dust and particulate monitor for measuring dust emission concentrations on industrial processes and non-compliance applications. This dust monitor is ideally suited to multiprocess plants with common exhaust stacks.

StackGuard - Dust Emission Measuring System

by Sigrist-Photometer AG     based in Ennetbürgen, SWITZERLAND

The StackGuard continuously monitors the scatted light intensity of an extracted, withdrawn sample of gas. The laser light source minimized stray light and improves sensitivity to the µg/m³ level, the filtered purge air prevents from window soiling. A calibration check is performed by means of a checking rod. The sample air is led out ...

Model SPX 150 - Dust Emission Monitoring Probe

by Sefram     based in Templemars, FRANCE

The SPX 150 is based on the tribo-electricity principle. It detects, warns, records and can be used for dust threshold. rejection trend analysis, from a 0.1  mg/m3 dust

Babbitt - Model FS10000 - Dust Emission Flow Switch

by Babbitt International, Inc.     based in Houston, TEXAS (USA)

Emissions from dust collectors and bag houses has become a major environmental issue. Babbitt has two products which monitor these processes, and assist in reducing the level of dust emissions. The FS10000 Flow Switch is able to alarm and/or shut down a dust collector when a weak filter is detected BEFORE it becomes a major failure and source of ...

Babbitt - Model FT4100 - Dust Emission Flow Transmitter

by Babbitt International, Inc.     based in Houston, TEXAS (USA)

The FT4100 is designed to sense dust emissions passing through a filter in a dust collector or bag house. This very sensitive device allows the user to continuously monitor the level of emission, and record the data.

SprayWall - Model NM20 - Weigh Down and Control Dust Emissions

by MB Dustcontrol BV     based in Voorschoten, NETHERLANDS

MB Dustcontrol uses SprayWall hoses to weigh down and control dust emissions. A SprayWall hose consists of a 3' fire hose with special exchangeable nozzles and supports so the fog/spray can reach every corner. With a maximum pressure of 10 Bar, we can throw a fog/spray wall (or ceiling) up to 10 metres high. The hoses are delivered in lengths of ...

Model V12S - Silent Dust Abatement Sprayers

by EmiControls     based in Bolzano, ITALY

The fully-automatic V12S offers a universal, powerful and super silent environmentally-friendly dust control solution. The specially designed 12,5 kW turbine is almost whisper quiet when running only producing 60 dBA at 20 m. The turbine has the ability to run at 2 speeds 1500 rpm and 1000 rpm giving the turbine the flexibility to throw the ...

Model L3 - Dust Abatement Sprayers

by EmiControls     based in Bolzano, ITALY

The L3 lance is the first dust-control lance on the market. It is a compact and user-friendly solution for close-range applications. It works without a turbine, allowing it to get near to the source of dust. The spray action can be narrow and flat, fan-shaped or cylindrical, depending on the requirements in any given case. With its flexible spray ...

Model V7 - Dust Abatement Sprayers

by EmiControls     based in Bolzano, ITALY

The V7 is the the V12 dust-laying sprayer’s little sister. The patented nozzle head on the V7 is fitted in the axial direction in the turbine and achieves a much higher projection range than comparable nozzle configurations. It has a booster pump and can therefore also be used with the turbine switched off. The user-friendly remote control ...

Need help finding the right suppliers?

Let the XPRTs do the work for you