continuous emissions monitoring Equipment in Nunavut

Served | Office inNear
128 Results found
  • Category: Air & Climate ×

  • Subcategory: Emissions Monitoring ×

  • Keyword: continuous emissions monitoring ×

  • Location: Canada ×

  • Location: Nunavut ×

Lowe Engineering - Continuous Emissions Monitoring ( CEM ) Systems

by Lowe Engineering Limited     based in Leeds, UNITED KINGDOM

Are you planning to install Emissions Monitoring or do you have a requirement for Gas Analysis? Lowe Engineering's great experience in systems for these two fields could save you money and give you peace of mind.

a1-cbiss - Model MIR-9000-CLD - Multi-Gas Continuous Emissions Monitoring System

by a1-cbiss     based in Birkenhead, UNITED KINGDOM

a1-cbiss and Environnement S.A have developed a multi-gas continuous emissions monitoring system utilising the Standard Reference Methods (SRM) for the monitoring of NO, N2O, NO2, NOx, CO, CO2 and O2. It also utilises the technology stated in the Alternative Reference Method (ARM) for SO2.

Lowe Engineering - Gas Sample / Detection Analysis

by Lowe Engineering Limited     based in Leeds, UNITED KINGDOM

The following extract from Perry's Chemical Engineers' Handbook, will give some insight into the sampling and analysis of Hydrocarbons.

Teledyne - Model ML675 - Dilution-Extractive System

by Teledyne Monitor Labs, Inc.     based in Englewood, COLORADO (USA)

The Teledyne ML675 dilution-extractive system can be used in 40CFR75, 40CFR60, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.

a1-cbiss - Model HM 1400 TR - Total Mercury Analyser

by a1-cbiss     based in Birkenhead, UNITED KINGDOM

a1-cbiss supply a monitoring system for fully-automatic and continuous mercury analysis in smoke gas (without wet chemistry). Measuring principle: In the HM 1400 TR total mercury analyser the sample gas is converted into mercury vapour by a combination of thermal and dry chemical treatment. This is then continuously measured in a photometer. The ...

Model MIR-9000 - Continuous Emissions Monitoring Systems

by a1-cbiss     based in Birkenhead, UNITED KINGDOM

Measurement Technique: Utilising Infra-Red Gas Filter Correlation allows the MIR-9000 to offer up to ten gas measurements simultaneously, including Nitric Oxide (NO), Nitrogen Dioxide (NO2), Sulphur Dioxide (SO2), Carbon Monoxide (CO), even Hydrogen Chloride (HCl) and Hydrogen Fluoride (HF).

Graphite - Model 52M - Heated FID Analyser

by a1-cbiss     based in Birkenhead, UNITED KINGDOM

Equipped with one burner placed in a heated block, the Graphite 52M allows continuous and accurate Total VOC monitoring. The FID is temperature controlled up to 191°C to eliminate condensation. Extremely compact and with a very short response time, this heated FID provides continuous monitoring of total VOC’s, in compliance with the ...

Model MIR-FTIR - Continuous Emission Monitoring Systems (CEMS)

by a1-cbiss     based in Birkenhead, UNITED KINGDOM

Measurement Technique: Installed across the majority of the UK’s municipal waste incinerators, the MIR-FT Utilises Fourier Transform Infra-Red (FT-IR) to offer multiple gas measurements simultaneously, including NO, NO2, SO2, NH3, HCl and CO. With the emissions limits tightening and new gases being introduced, this instrument allows future ...

Model MIR-IS - In-Situ Multi-Gas Compact Extractive Monitoring System

by a1-cbiss     based in Birkenhead, UNITED KINGDOM

Based on the MIR-9000, this in-situ multi-gas CEM system is a compact extractive monitoring system, providing fast response, close coupled measurements. CEM Systems are required to satisfy environmental led legislation within industrial applications.

IntelliCEMS - Model IC Series - Straight Extraction Or Dilution Extraction Systems

by Cemtrex Inc.     based in Farmingdale, NEW YORK (USA)

The IC Series IntelliCEMSTM include straight extraction or dilution extraction systems complete with sample probes, heated sample bundles, sampling systems, analyzers, and Data Acquisition Systems (DAS). Our CEMS are pre-engineered and packaged to measure a wide range of gases and pollutants for compliance with state and federal EPA regulations ...

Related Terms for continuous emissions monitoring

Need help finding the right suppliers?

Let the XPRTs do the work for you