exhauster Equipment in Mississippi

Served | Office inNear
288 Results found
  • Category: Air & Climate ×

  • Subcategory: Exhaust ×

  • Keyword: exhauster ×

  • Location: USA ×

  • Location: Mississippi ×

Exhausters With Pre-Inlet

by Aerzener Maschinenfabrik GmbH     based in Aerzen, GERMANY

For pre-inlet cooling the housing is equipped with an additional third socket on the suction side. The lube oil supply is effected by splash oil lubrication. The conveying chamber is sealed by a sealing system. Driving shaft by double radial seal rings with grease barrier. Direction of flow vertically from top to bottom. The drive can be effected ...

HI-Q - Sample & Return Exhaust Lines

by HI-Q Environmental Products Company     based in San Diego, CALIFORNIA (USA)

Many air sampling procedures call for remote site sampling where the vacuum source (air sampling pump) cannot be conveniently located in the same area where sampling is required. This may be due to a variety of reasons including explosive sampling environments, inaccessibility, and noise level restrictions. For this reason, HI-Q has developed two ...

Exhaust Back Pressure Control Valve

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

Our exhaust back pressure control and simulation package centers around our proprietary exhaust back pressure valve, a fast-acting ALL stainless steel butterfly valve controlled by an electronic actuator. The valve adjusts to accurately simulate the effective back pressure of a full vehicle exhaust system, but on a closed test bed ...

ExhaustTrak - Model Sierra CP Series - Raw Engine Exhaust Mass Flow Meter

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

Sierra CP has successfully manufactured and sold AirTrak intake air mass flow meters since the early 1990's.  With deep roots in flow measurement through our Flow Division, we have

Kleissler PC - Local Exhaust Ventilation and Dust Control Hoods (LEV)

by Kleissler P C, LLC     based in Avon-by-the-Sea, NEW JERSEY (USA)

Kleissler P C has experience in all pharmaceutical manufacturing processes.  The below slideshow includes examples of some of the pharmaceutical applications for which Kleissler P C has designed hoods.

Emission Concentrators

by Anguil Environmental Systems, Inc.     based in Milwaukee, WISCONSIN (USA)

Reducing the air volume being sent to a thermal or catalytic oxidizer can save companies a significant amount of money in operating and capital equipment costs. Anguil's Rotor Concentrator is designed to concentrate large volume, low concentration process exhaust into a much smaller, highly concentrated air stream. The pollutant laden air is then ...

HORIBA - Model CVS-ONE Series - Constant Volume Sampler

by HORIBA Europe GmbH     based in Leichlingen, GERMANY

The CVS-ONE series is designed for the measurement of diluted emissions from vehicles and engines. The new integrated operating platform, HORIBA ONE PLATFORM is adopted for the CVS-ONE. The hardware has been significantly downsized from previous designs, reducing test cell footprint requirements. It introduces new functions and is more ...

Elite - Model BG-3 - High Performance Partial Flow Dilution System

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

In use since 2004, BG3 PFD (Partial Flow Dilution) technology effectively performs engine research and development to accurately sample exhaust PM (Particulate Matter) emissions over both steady state and transient test cycles (Read Case Study). On January 7, 2011, PFD was signed into law and is now included in the United States Federal Register ...

BWE Membrane-gas treatment unit

by bwe biogas-weser-ems GmbH & Co. KG     based in Friesoythe, GERMANY

In modern combined heat and power units around 85 % of the energy from the exhaust gas can be recovered and used as thermal power. However, an effective heat concept is required to utilise the whole potential. The excess of thermal energy is suitable for heating nearby buildings or supplying hot water to remote users through a district heating ...

Model EGAS 2M - Engine Exhaust Gas Analysis System

by Environnement S.A     based in Poissy, FRANCE

The only system allowing the measurement of 1 or 2 independent streams in a single analysis cabinet. Measurement of THC, NO, NO2, NOx, CO, CO2, O2 and NH3. Designed to measure emissions from all combustion engines regardless of fuel type.

Related Terms for exhauster

Need help finding the right suppliers?

Let the XPRTs do the work for you