78 Products found


Data Loggers

Ammonit - Model Meteo-40 - Meteo Data Logger

The Meteo-40 data logger is the heart of your measurement system. The data logger ensures accurate measurements to the high standards required by professional consultants, operators and climate research institutes. The Meteo-40 series is designed for wind and solar resource assessment as well as for monitoring of wind farms and solar power plants. Additionally, Meteo-40 can be implemented in traffic and agricultural meteorology. Meteo-40 data loggers...

Sensors - Anemometers

Vector - Model L100 - Anemometer

The anemometer should ideally be mounted at the top of a mast to be open to the wind from all directions. Only a lightning protection rod mounted below may overtop the sensor. If an anemometer has to be mounted on a traverse the length must be at least 7 times the mast diameter.

Model P2546A - Cup Anemometer Windsensor (Risø)

The P2546A Cup Anemometer is a sturdy wind sensor solely constructed by durable materials such as anodized aluminium and stainless steel. The wind speed is sensed by a three-cup rotor assembly. Permanent magnets mounted on the shaft causes a switch to close and open two times per revolution. The switch has no bounce and it is equipped with a special built-in mechanism, which reduces the variation in operating time over the frequency range. This...

Propeller Anemometer Young 27106T

The Young Propeller Anemometer is a low threshold precision air velocity sensor employing a fast response helicoid propeller. The sensor uses a high quality tech-generator transducer which converts propeller rotation to a DC voltage that is linearly proportional to air velocity.

Sensors - Humidity Temperature

Temperature / Humidity Sensor

The temperature-humidity-transmitter series are compact sensors in stick version with fixed connected cable. The relative humidity is measured by a capacitive sensing element and the value will be placed at the output as analogue signal. The temperature measurement is made by a Pt100-resistor (1/3 DIN). The signal is available as an analogue output as well. The sensors are obtainable as single temperature probe or as combined sensor for temperature...

Sensors - Barometers

Barometric Pressure Sensor AB60

The piezoelectric pressure sensor’s signal is electronically amplified to provide an output signal of 0...5 VDC. The sensor is mounted in a stainless steel housing, protection class IP64 when the connector is plugged in. The connecting cable is included in delivery. If required it will be ready for connection in an Ammonit steel cabinet. When mounted outside the central steel cabinet we recommend protective housing with pressure compensation. In...

Barometric Pressure Sensor AB100

The piezoelectric pressure sensor’s signal is electronically amplified to provide an output signal of 0...5 VDC. The sensor is mounted in a stainless steel housing, protection class IP64 when the connector is plugged in. The connecting cable is included in delivery. If required it will be ready for connection in an Ammonit steel cabinet. When mounted outside the central steel cabinet we recommend protective housing with pressure compensation. In...

Sensors - Solar Radiation

Pyranometer EKO MS-802 Secondary Standard

The MS-802 highest class ISO Secondary Standard is used for the most demanding applications in PV, Meteorology, field research and solar radiation monitoring of global, tilted and diffuse irradiance. Thermopile, which has a flat spectral response at all wavelengths, is integrated as a sensor. Thermopiles generate electricity by thermo-electric effect, which is caused by the temperature difference between hot and cold junctions. Solar irradiance is...

Pyranometer EKO MS-410 First Class

The MS-410 is perfectly suited for sampling 10-minute averages of the solar radiative flux in horizontal or tilted configurations. The flat sensor surface, coated with a special, highly absorbing black paint, is protected by two transparent hemispheric glass domes. MS-410 has a 180° field-of-view for measuring the hemispheric solar radiation with a cosine-weighting function. The two transparent glass domes protect the sensor efficiently from negative...

Pyranometer EKO MS-602 Second Class

MS-602 detector consists of a special polymer film with the advantage of having very small temperature response and long-term durability. Thermopile detects temperature difference between the center- and the peripherally mounted hot and cold junctions, respectively. Hot and cold junctions are positioned radially. Detector is coated by special black paint, which has independent wavelength.

Pyranometer Delta-T Sunshine SPN1

The Sunshine Pyranometer is a patented, meteorological class instrument, with built-in heater, designed for long-term outdoor exposure. It is an affordable alternative to shade-ring pyranometers, pyrheliometers and traditional sunshine recorders. The SPN1 is exceptionally easy to use; it needs no routine adjustment or polar alignment and works at any latitude.

Ammonit AQ510 windfinder - Remote Sensing Systems (LiDAR + SoDAR)

Remote sensing systems have become more and more popular in the wind industry as a supplement to the traditional met mast. Remote sensing systems can be applied to complement a wind site assessment campaign or for wind farm monitoring. The systems measure the wind conditions from the ground up to a height of 200m. Thus the wind speed and wind direction up to rotor blade tip-height or for the whole rotor blade area can be used to calculated the wind energy yield forecast.

AQ510 windfinder

Ammonit AQ510 windfinder has been developed for wind site assessment as well as wind farm monitoring. The Sodar system is easy to use. Conveniently position the system with the help of the integrated tilt sensor and GPS mo-dule at your selected site and switch it on. You instantly collect wind data. It has never been easier to measure wind. The mobile and self-sufficient Ammonit AQ510 windfinder can quickly be moved from site to site to explore the...

ZephIR 300

LiDAR systems are increasingly being used in the wind industry for site assessment, power curve measurement as well as wind farm monitoring. As Trusted Service Provider, Ammonit offers the leading ZephIR Lidar systems: ZephIR 300 for ground-based installations and ZephIR DM for turbine-mounted applications. According to the clear and auditable staging process by DNV GL, ZephIR 300 wind LiDAR is accepted for use in finance-grade wind speed and energy...

Obstacle Lights

Aviation & Obstacle Light Carmanah A650

Up to 10 cd of intensity (steady-on, green, equatorial). Replacable and recyclable battery pack.

Aviation & Obstacle Light Carmanah A702-5

Distance of visibility up to 3 miles (5.4 km). Night vision goggle (NVG) compatible. Programmable via optional infrared remote control.. Features both four and five-bolt mounting patterns.. Available in red, green, amber, white and blue. Completely self-contained and sealed against environmental. conditions. Extremely rugged, waterproof. and vandal resistant.. Easily mounted to standard frangible coupling. Replacable batteries available. Maintenance free...


Automatic Weather Stations

Vaisala HydroMet - Model MAWS110 - Automatic Weather Stations System

The Vaisala HydroMet™ System MAWS110 is a compact, robust and easy to use system which provides quality controlled data for both  meteorological and hydrological applications. The system is especially designed for unattended operations requiring high reliability and accuracy at sites with the mains power and with battery back-up. The MAWS110 uses a field proven and high accuracy data logger and advanced software. Every system can...

Power and Energy - Weather Measurement - Remote Sensing Systems

Vaisala Triton - Sonic Wind Profiler

Vaisala's Triton Wind Profiler is an advanced sodar system that provides accurate wind measurement data across the entire blade sweep of today's largest wind turbines. With hundreds of Triton sodar systems in commercial use on wind development projects and working wind farms, and millions of hours of wind data gathered, the Triton sodar is the wind industry's market-leading remote sensing system.

Power and Energy - Weather Measurement - Met Tower Loggers and Sensors

Vaisala Nomad 2 - Wind Data Logger

Redesigned from the ground up, the Nomad 3 is rugged, easier to use, and more lightweight than its predecessor. The Nomad 3 allows you to connect all market-leading sensors without any hardware modifications, and is easy to install. It works with modern communications networks and meets all industry standards and requirements.

Vaisala SWI - Model C3 - Three-Cup Anemometer

The C3 Anemometer is an improved, economical version of the popular three-cup design used in wind assessments for decades, manufactured to precise industry standards. The Model C3 rotor is made of tough polycarbonate for exceptional durability and reliability. The Model C3 sensor base is also made of rugged polycarbonate, making it more resistant to damage during installation.

Vaisala - Model PV-1 - Wind Vane

The standard vane used in the wind energy industry. Stainless steel and thermoplastic construction for corrosion resistance. The PV-1 was developed by Second Wind in response to our customers in the field. Earlier technology too often fell short in its ability to accurately capture data in every direction and in cold, icy environments.

Vaisala SWI - Thermistor

The SWI Thermistor is designed specifically for use with the Nomad 2 wind data logger. It consists of a 10K type thermistor encased in an aluminum shaft, and comes pre-wired with 3.5 meters of sensor cable. The thermistor's resistance changes with temperature, following a known but non-linear curve. The Nomad 2 measures the resistance of the thermistor and uses a lookup table with over 4,096 values to determine the temperature. The sensor is wired to...


Model 2AP - Sun Trackers

Accuracy suitable for any requirement .All-weather construction.Wide range of mounting and payload configurations.The 2AP tracker is an all-weather, reliable and affordable tracking and positioning instrument. It is used to accurately point small and medium sized payloads, either as a dedicated sun tracker or as a computer based positioner. The 2AP incorporates two stepper motors controlled by an on-board micro-computer. After configuration as sun...


Kipp & Zonen - Model SP Lite2 - Silicon Pyranometer for Routine Measurement of Solar Radiation

SP Lite2 is ideal for measuring available energy for use in solar energy applications, plant growth, thermal convection and evapotranspiration. SP Lite2 is designed for routine measurement of solar radiation. It is especially designed for: Photovoltaic / solar energy module monitoring, agricultural evapotranspiration estimation, air pollution dispersion calculations using the delta-t method, educational purposes. SP Lite2 can be used under all weather...

Kipp & Zonen - Model CM 4 - High Temperature Pyranometer for Measuring Solar

The CM 4 High Temperature Pyranometer is a radiometer specially designed for measuring solar or artificial light irradiance under the most extreme temperature conditions. With an operating temperature range of -40 ºC to +150 ºC and measurement up to 4000 W/m² it is a unique product. All the radiometer components are specially selected for their ability to withstand these extremely high temperatures and irradiance. The CM 4 is supplied...

Kipp & Zonen - Model CMP 3 - Pyranometer for the Accurate Measurement of Solar Irradiance

The CMP 3 is a low cost pyranometer for accurate routine measurements in many applications. The CMP 3 pyranometer is an instrument for measuring the solar irradiance. The thermopile sensor construction measures the solar energy that is received from the total solar spectrum and the whole hemisphere (180 degrees field of view). The output is expressed in Watts per meter square. The CMP 3 pyranometer is designed for continuous indoor and outdoor use.

Kipp & Zonen - Model SMP3 - Smart Pyranometer for Monitoring Solar Energy

Fastest and best performing ISO 9060 Second Class pyranometer. Smart Pyranometer SMP3 is perfect for monitoring solar energy installations, agriculture, horticulture, hydrological and industrial applications. The SMP3 is a smart pyranometer with low maintenance and industry standard digital and analogue amplified outputs. Based on the proven CMP 3 technology the SMP3 adds Modbus interface, improved response time and temperature corrected measurement...

Kipp & Zonen - Model CMP 6 - Pyranometer for Routine Global Solar Radiation Measurement

Pyranometer for good quality measurements for green-house climate control, field testing and PV installations.  The CMP 6 pyranometer is intended for routine global solar radiation measurement research on a plane/level surface. Fully compliant with ISO 9060:1990 specification for a First Class pyranometer, the CMP 6 features a sixty-four thermocouple junction (series connected) sensing element. The sensing element is coated with a highly stable...

Kipp & Zonen - Model CMP10 - Secondary Standard Pyranometer

Secondary standard pyranometer with minimized maintenance thanks to its internal desiccant, designed for meteorological networks and solar energy applications. CMP10 is the secondary standard pyranometer with the best price-quality-performance ratio on the market. Based on the established CMP 11 technology, CMP10 extends this quality to applications where maintenance is difficult and/or forms a major part of the cost of ownership. The CMP10 has an...

Kipp & Zonen - Model CMP 11 - Pyranometer for Meteorological Networks, Reference Measurements

Pyranometer for Meteorological networks, reference measurements in extreme climates, polar or arid. It is the industry standard for solar radiation monitoring in PV and thermal energy plants. CMP 11 uses the temperature compensated detector technology originally developed for the CMP 22 and is a step up in performance from the CMP 6. It is particularly suitable for meteorological networks and the reduced response time of 1.66 seconds (63%) meets the...

Kipp & Zonen - Model SMP11 - Pyranometer for High Quality Solar Radiation Monitoring

Exceeds the requirements for ISO Secondary Standard pyranometers. Smart Pyranometer SMP11 is the ideal choice for high quality solar radiation monitoring in meteorology and solar energy. The SMP11 smart pyranometer combines class leading sensor technology with industry standard digital and analogue amplified outputs. Based on the proven CMP 11 technology the SMP11 adds Modbus interface, improved response time and temperature corrected measurement...

Kipp & Zonen - Model CMP 21 - Pyranometer for Meteorological Networks, Reference Measurements

Pyranometer for Meteorological networks, reference measurements in extreme climates, polar or arid. The CMP 21 is a high performance research grade pyranometer, and is fully compliant with all ISO 9060:1990 Secondary Standard Instrument performance criteria (highest possible ISO pyranometer performance category). The CMP 21 pyranometer is designed for measuring the irradiance (radiant flux, Watt/m²) on a plane surface, which results from the...

Kipp & Zonen - Model CMP 22 - Pyranometer for Scientific research

Pyranometer for Scientific research requiring the highest level of measurement accuracy and reliability. CMP 22 has all the features of CMP 21 but uses very high quality quartz domes for a wider spectral range, improved directional response, and reduced thermal offsets. Because of the high optical quality of these domes the directional error is reduced below 5 W/m². Kipp & Zonen is confident that CMP 22 is the best pyranometer currently...


Ultrasonic Anemometers & Wind Sensors

WindSonic - Model M - Ultrasonic Wind Sensor

WindSonic M is a robust ultrasonic wind speed and direction sensor with aluminium alloy construction and optional heating system. The sensor is solid-state with no moving parts, using ultrasonic measurement technology to detect wind speed and direction at speeds up to 60m/s (134mph).The robust aluminium alloy housing is hard-anodised to ensure suitability in harsh marine environments, and the optional heating system allows operation down to...

WindSonic - Low Cost Ultrasonic Wind Sensor

WindSonic is a robust, low cost ultrasonic wind sensor with no moving parts. This 2-axis ultrasonic wind sensor offers maintenance-free wind speed and direction monitoring for true ‘fit and forget’ wind sensing.The Gill WindSonic is a genuine low cost alternative to conventional cup and vane or propeller wind sensors, with all of the advantages of solid-state ultrasonic technology. With no moving parts to jam, break or wear out, this...

WindObserver - Model II - Wind Speed Sensor

The WindObserver II wind speed sensor is an ultrasonic 2-axis anemometer for the measurement of wind speed and direction. With no moving parts this wind speed sensor is ideal for use in extreme environments.The WindObserver II utilises the same high-performance measurement technology as the Gill WindSonic wind speed sensor, with some additional features to extend the application potential of the sensor. The WindObserver II wind speed sensor has a high...

WindObserver - Model 65 - Wind Speed Sensor

The Gill WindObserver 65 is a precision, solid-state ultrasonic anemometer providing wind speed and direction data via 1 digital and 3 optional analogue outputs and features an IP66 rated stainless steel housing, which is particularly suitable for use in salt-water environments.Offering a high wind speed measurement range, this anemometer has an optional de-icing system enabling the sensor to operate effectively in environmental conditions experienced...

WindObserver - Model 70 - Heated Anemometer

The WindObserver 70 is a solid state, heated ultrasonic anemometer designed for use within the aviation industry. The sensor has been accepted for service by both the FAA Federal Aviation Administration (USA) and the CAA Civil Aviation Authority (UK) for the observation and reporting of surface wind. This WindObserver meets the requirements of Annex 3 to the Convention on International Civil Aviation Organization (ICAO) when supplied as part of a...

WindObserver - Model 75 - Heated Anemometer

The WindObserver 75 has been developed for measuring higher wind speeds in extreme weather environments featuring 150 Watts of electrical heating power in the anemometer head. This anemometer has been designed to remain ice free in most freezing weather conditions. The sensor provides data via RS422/RS485 bidirectional link, which allows several units to be networked together and data logged on demand.

WindMaster - Model 3D - Sonic Anemometer

The WindMaster 3D sonic anemometer will monitor wind speeds of 0-45m/s (0-100mph), providing digital outputs for U, V, and W vectors. Outputs for Speed of Sound and Sonic Temperature are available as standard.WindMaster is constructed from aluminium and carbon fibre and is available with either a 20Hz or 32 Hz data output rate. Optional analogue inputs and outputs are available with either 12 or 14 bit resolution.

WindMaster - Model Pro 3 - Axis Anemometer

The WindMaster Pro is constructed from stainless steel and has a maximum operating wind speed of 65 m/s. With a fast maximum data output rate of 32Hz as standard, improved vertical (W) resolution and Speed of Sound accuracy and less distortion due to wind loading, this 3-axis anemometer is particularly suitable for precision wind measurement applications requiring 3-axis data.Optional analogue inputs and outputs plus a PRT are available with 14 bit...

Model R3-50 - Professional 3D Anemometer

The R3-50 3-axis anemometer has been designed for scientific research, particularly suitable for determining fluxes using the eddy covariance technique.This precision ultrasonic anemometer will monitor wind speeds up to 45m/s, with a fast data output rate of 50Hz (100Hz model available, click here to view). U, V, W and SOS (sonic temperature) outputs are available, and data can be logged using the supplied Gill WindCom software.

Model R3-100 - Research Anemometer

The R3-100 anemometer is ideal for scientific research applications, with a fast sampling rate of 100Hz. This 3-axis ultrasonic anemometer is used extensively for the determination of fluxes using the Eddy Covariance method.R3-100 will monitor wind speeds of 0-45m/s at environmental operating temperatures of -40ºC to +60ºC. Analogue, sonic temperature, speed of sound and U,V,W vector outputs are provided as standard, with optional analogue...

Model HS-50 - Horizontal-Head Ultrasonic Anemometer

The HS-50 horizontal-head anemometer has been designed for scientific research applications requiring accurate 3-axis wind speed and direction information.This instrument utilises advanced ultrasonic measurement technology, with a unique horizontal head design that allows for more accurate measurement of vertical flows with minimal interruption from the anemometer geometry. The head features a built-in inclinometer for simple positioning of the...

Model HS-100 - Horizontal-Head Ultrasonic Anemometer

The HS-100 3-axis anemometer features a horizontal head design, which allows for accurate measurement of vertical flows with minimum flow interruption from the anemometer geometry.Ideal for scientific research applications, HS-100 is capable of monitoring wind speeds of 0-45m/s and offers a fast update rate of 100Hz for precision wind analysis.The head of the anemometer features a built-in inclinometer to allow the instrument to be accurately...

Weather Stations

MetPak - Model Pro - Weather Station

MetPak Pro includes the same on-board sensors as the MetPak II as standard. The new MetPak Pro allows the integration of up to four sensors (e.g rain gauge, water level, pyranometer, pressure and soil temperature) in addition to the wind speed, wind direction, temperature, barometric pressure, humidity and dew point sensors supplied. Software to allow the customer to configure the system, display and log data is available free of charge from Gill....

MetPak - Model II - Multi-Sensor Weather Station

The MetPak II has been newly developed to replace the original MetPak weather station. Monitored parameters include: Wind Speed & Direction; Air Temperature; Relative Humidity; Barometric Pressure and Dew Point.

MetPak - Model II - Weather Station with Remote Wind Sensor

MetPak II Remote features the same wide range of weather monitoring capabilities as the MetPak II, with a remote wind sensor that is suitable for mounting up to 10m away from the main weather station unit.

WindDisplay - Wind Speed Indicator

Gill wind displays are designed for use with our range of two-axis wind speed and direction sensors. Displays are available in two formats - standard and nautical, both with bright LED display panels for clear representation of wind data.


Solar Radiation & Photonic Sensors - Pyranometers

EKO - Model MS-802 - Secondary Standard Pyranometer

The MS-802 Secondary Standard Pyranometer is the ultimate reference sensor to measure global solar irradiance with the highest precision. Its robust brass mechanical construction makes it a durable sensor suitable to be used in harsh environments. The MS-802 is used as standard for PV research and climatology studies around the world. In combination with a Sun tracker (STR-series) or manual shading ring (RSR-01), respectively the Global Normal...

EKO - Model MS-402 - Pyranometer

The MS-402 Pyranometer is a unique ISO First class pyranometer and best in its category. As the only first class sensor available on the market it has a built in electronic passive temperature compensating to linearize the detector temperature coefficient and make it accurate under all temperature conditions. The design of the MS-402 First Class Pyranometer is very similar to the Secondary standard MS-802. Its robust brass mechanical construction...

EKO - Model MS-410 - Pyranometer

The MS-410 pyranometer measures the broad-band global solar irradiance. The MS-410 is perfectly suited for sampling 10-minute averages of the solar radiative flux in horizontal or tilted configurations. It is fully compliant with the ISO9060 'First Class' norm. The flat sensor surface, coated with a special, highly absorbing black paint, is protected by two transparent hemispheric glass domes. The MS-410 has a practical light-weight anodized aluminum...

EKO - Model MS-602 - Pyranometer

Within the MS-series the MS-602 pyranometer is the smallest true thermopile pyranometer. It is the most economic measurement solution for global solar radiation measurements capturing the full solar spectrum. MS-602 meets the ISO Second Class performance criteria. However, its outstanding temperature dependency characteristics can only be found on higher class pyranometers. This sensor can be found in many meteorological networks and professional...

Solar Radiation & Photonic Sensors - Pyrheliometer

EKO - Model MS-56 - First Class Pyrheliometer

The ISO First Class MS-56 is a direct normal incidence (DNI) solar irradiance sensor. Also known as a pyrheliometer, it is used as a reference sensor for routine operation on a Solar Tracker. The all-weather MS-56 is sensitive to solar irradiance in the spectral range 200 – 4000nm and works under the most extreme conditions in a temperature range from -40°C...+80°C.

Solar Radiation & Photonic Sensors - Spectroradiometers

EKO - Model LS-100 - Grating Spectroradiometer

The LS-100 grating spectroradiometer is specially designed for measuring the spectral irradiance of solar simulators which are used in solar cells ressearch. The LS-100 is calibrated against a NIST-traceable standard lamp. It is compact and very easy to operate. The LS-100 is controlled by a PC via a RS232C cable, so that data can be automatically obtained using the operating software. The measurement/analysis software offers advances functionalities...

EKO - Model MS-700 - Grating Spectroradiometers

The compact all-weather MS-700 spectroradiometer is unique in many ways. It is as reference instrument for outdoors spectral irradiance measurements in many high-end research applications. The MS-700 covers a spectral range from 350nm to 1050nm and benefits from an advanced spectrometer which gives a stable output over time. The detector unit is temperature controlled at a fixed temperature to maximize the performance in a wide operating temperature...

EKO - Model MS-720 - Portable Grating Spectroradiometer

MS-720 portable spectroradiometer is designed to measure the spectral irradiance in the range from Visible to Near-Infrared. The MS-720 is mainly used for the data acquisition for geological features, vegetation, oceanography, remote sensing and other applications. MS-720 is a handheld sensor with an integrated LCD and an internal memory. Therefore, it is suitable for outdoors stand-alone measurements. A small-sized stable grating spectrometer with...

ECO - Model MS-710 / 712 - Spectroradiometer

The unique combination of MS-710 and MS-712, called 'WISER system', operates as a set to extend the spectral measurement range and maximize resolution. From a single PC, the stand alone units are controlled by an integrated software which combines the individual measurement spectra into one file. The spectral measurement range of MS-710 is between 350nm and 950nm (VIS and NIR) and overlaps with the MS-712 which is between 900nm and 1700nm (NIR). The...

Solar Radiation & Photonic Sensors - Small Sensors

ECO - Model ML-01 - Si-Sensor

The ML-01 Si-sensor is the link between the reference cell and broadband thermopile pyranometer. Compared to the reference sensors it has a proper cosine repose and it is relatively compact, but benefits from the same characteristics as a PV module (Response time, Spectral and temperature response). The ML-01 is an industrial grade solar sensor specially made for Performance ratio measurements as well as irradiance measurement applications for the...

ECO - Model ML-020P - PAR Sensor

The compact ML-020P PAR sensor or Quantum sensor has a special opical filter to mimic the spectral response function of typical plant leaves. The PAR sensor is most common to be used in horticulture or agriculture aplications. The photon active range between 400 - 700 nm represents the Photosynthetically Active Radiation (PAR) known as Photosynthetic Photon Flux (PPF) or Photosynthetic Photon Flux Density (PPFD) in μmol/m/s (micromoles of photons...

ECO - Model ML-020S - Lux Sensor

The MS-020S-O and ML-020S-I illuminance sensors are both all-weather sensors having customized detector sensitivities for either indoor low light level or outdoors high light level applications. The built-in interference filter in conjunction with the detectors spectral response reproduces the CIE photopic curve and gives a calibrated output in lux (lx). Both sensors can be found in many professional applications to control or monitor industrial...

Solar Radiation & Photonic Sensors - UV Radiometers

ECO - Model MS-212A - UVA Sensor

The precision UV-A Radiometer MS-212A is designed to measure UV-A radiation with high reliability. It is calibrated against a NIST traceable standard. The combination of a well-designed UV-A filter and a GaAsP photodiode guarantees its high performance to measure UV-A between 315 and 400nm. The energy in this spectral range accounts for 4 to 5% of the total solar radiation.

ECO - Model MS-212W - UVB Sensor

The precision UV-B Radiometer MS-212W is designed to measure UV-B radiation with high reliability. It is calibrated against a NIST traceable standard. The combination of a well-designed UV-B filter and a GaAsP photodiode guarantees its high performance to measure UV-B between 280 and 320nm. The energy in this spectral range accounts for 4 to 5% of the total solar radiation.

Model MP-160 - I-V Curve Tracer

The past few years has seen mass production of Silicon PV cells (solar cells, the synonym for the PV cell), and better and better cell performance, as well as larger and larger sized cells. Furthermore, extensive research efforts in recent years has resulted in the development of Compound Semiconductor and Dye-sensitized Solar Cells  which may very well highlight the next generation of PV cell technology. EKO has more than 10 years experience in...

Model MS-54 - Pyrheliometer

The MS-54 Pyrheliometer is designed for unattended normal incidence direct solar radiation measurement research, from 0.2 to 4.0 µm. The MS-54 is intended for use with STR series EKO Sun Tracker. The MS-54 fully complies with the most current ISO and WMO performance criteria, for that of a First Class Normal Incidence Pyrheliometer. Every MS-54 is calibrated upon manufacture, and is supplied standard with a WRR (World Radiometric Reference)...

Model MS-212A - UV-A Radiometer

Precision UV-A Radiometer MS-212A is designed to measure an amount of UV-A radiation with high reliability of NIST traceable. The combination of well-designed filter and GaAsP photodiode contribute the high performance to measure UV-A between 315 and 400nm, which accounts for 4 to 5% of the total radiation, in various solar-altitude and spectrum affected by atmospheric conditions.

Model MS-093 - Sunshine Duration Meter

The WMO has defined sunshine duration as the time interval when direct solar radiation exceeds 120W•m-2. The EKO MS-093 Sunshine Duration Meter utilizes a pyroelectric sensor, one type of thermal sensor, that outputs a time differential coefficient processed for reliable measurement of only the direct solar radiation, without being affected by the diffuse radiation, integrated over the period when it exceeds a threshold value of 120W•m-2.

Model MP-170 - IV-Checker

MP-170 is a state-of-the-art instrument to measure I-V curve characteristics to evaluate the performance of PV modules and systems. Especially designed to measure 10W PV modules to 10kW PV systems, the MP-170 has a measurement range of up to 1000V making it well suited for larger voltage PV arrays. It is very cost effective, compact, portable and includes a solar irradiance sensor, two temperature sensors, and failure analysis functions. The Sensor...


Relative Air Humidity


Air Pressure




Measuring instrument to determine the air humidity values based on the dry and moist temperature. A water container provides for the moistening of the psychro sensor. The double-walled protection tubes protect the sensor from radiation.

Hygrograph - Recording Measuring Instruments

Measures and records the relative humidity. Registration is done on recording charts which are stretched onto a hand wound clock drum acc. to DIN 8300 and DIN 58658 or a quartz clock work. Delivery is effected with a set of recording charts (100 sheets) and recording pens.

Clima - Model D Series - Sensor

The output voltages might be used for the control of external instruments and/or the acquisition of analogue measuring data.The sensor combines perfectly the sensors for the 5 most important parameters, necessary for the control and monitoring in the field of building control technology, household technology, Venetian- and sun- blind regulation as well as green house control. The compact construction allows a simple and easy mounting.

Digital Baro Transmitter

Indicating measurement instrument with analogue output to determine the atmospheric pressure. An aneroid capsule with inductive displacement pickup serves as a sensor. The sensor signal is amplified electronically and displayed digitally on a LED- display. The current output is available for the connection of electronic recording and control instruments.

Model SDE Series - Sunshine Recorder

Registers the sunshine duration over one day. A cut glass sphere focuses the sun's rays and leave an image line on the strip chart. The length of the image corresponds to the duration of sunshine. The shipment includes the following charts: 140 sheets for summer, 140 sheets for winter, 100 sheets for spring and autumn.

Laser Precipitation Monitor

The Thies Laser Distrometer is especially designed for the use in several applications and characterization of precipitation. Thanks to a multitude of measuring variables and configuration variants the use of a Distrometer in various ranges of application is now possible.The optical laser basing measuring principle guarantees a reliable and accurate measurement of all known kinds of precipitation. It is possible to measure the...


Indicating humidity measuring instrument with resistance output. Sturdy construction. The outer parts such as the case head and the immersion stem are made of stainless steel.

Ventilated Air Temperature Transmitter

This instrument is designed to measure the precise air temperature, with ventilated measuring sensor. The sensor is protected by a double thermal radiation shield. A built-in ventilator provides for the necessary air flow.

Baro Transmitter

An electrical transmitter which indicates directly the measured values of the atmospheric air pressure. The measured value is indicated and delivered as electrical resistance value.

Baro Transmitter B-278-1/2 T

Baro transmitters measure the barometric ambient pressure and emit the measured value as an electrical voltage value. Owing to its low current consumption, It is particularly suitable for use in combination with data loggers. To be mounted preferably in data logger systems.


This instrument is used to measure and record the atmospheric air pressure. The recording is carried out by means of a hand wound clock work drum mechanism acc. to DIN 8300 and DIN 58658 (3.0800…; 3.0804…) or with a Quartz clock work (3.0804…). The on-site-elevation can be set by means of an adjusting screw.

78 Products found
Environmental XPRT is part of XPRT Media All Rights Reserved