Burner Systems Equipment

694 Results found
  • Category: Energy & Renewables ×

  • Subcategory: Burner Systems ×

Kurz - 534FTB - Inline Mass Flow Meter

by Kurz Instruments, Inc.

The Series 534FTB uses Kurz MFTB Technology with the advantages of built-in inlet/outlet piping reducers/expanders and exceptional immunity to upstream/downstream flow disturbances caused by elbows, valves and line size changes. This creative design eliminates the need for field fabrication and assembly of inlet and outlet mating pipe sizes. The ...

Kurz - 504FTB - Inline Mass Flow Meter

by Kurz Instruments, Inc.

The Series 504FTB utilizes the same Kurz MFTB Technology as above but is designed for applications where flow disturbances or line size changes is not an issue. The 504FTB has 10 models covering Mass Flow ranges to 1000 SCFM for inline sizes from ½” to 4” pipes.

BDS - Belt Drying System for Sludge

by ANDRITZ Separation - a division of the Andritz Group

Flexible and low-grade energy use The patented ANDRITZ AG belt drying system (BDS) is characterized by its flexibility and ability to use a wide range of energy sources, particularly low-grade waste energy. BDS can be used for drying a broad range of products, such as industrial and municipal sludge, cow manure, biomass, as well as pre-treated ...

Thermal Deoilers

by Epcon Industrial Systems, LP

Thermal Deoiling is a process that uses indirectly heated dry air to clean parts contaminated with oils or lubricants. No water, solvents or other chemicals are used. The basic thermal process is well known, having been used for many years in industrial operations that require clean, dry parts such as brazing, coating, soldering and plating.

Flue Gas Recirculation Systems

by Epcon Industrial Systems, LP

Flue Gas Recirculation (FGR) acts to reduce NOx formation by reducing peak flames temperatures. In conventional applications, the recirculated flue gas is typically extracted from the boiler outlet duct upstream of the air heater. The flue gas is then returned through a separate duct and hot gas fan to the combustion air duct that feeds the wind ...

Halogenated Components Oxidizers

by Epcon Industrial Systems, LP

Epcon Industrial Systems designs and manufactures pre-engineered and pre-tested Afterburners, Recuperative Thermal Oxidizers and Regenerative Thermal Oxidizers (RTO) for highly corrosive Halogenated (Chloride, Bromide, HF, etc.) Component Systems. Afterburners are installed between the oxidizer and the vapor source.

H2S Oxidizers

by Epcon Industrial Systems, LP

Epcon Industrial Systems designs and manufactures pre-engineered and pre-tested Regenerative Thermal Oxidizers (RTO) and Recuperative Thermal Oxidizers for H2S Systems. Afterburners are available; they are installed between the oxidizer and the vapor source.

VECTOR - 4,0000 - Catalytic Oxidizer

by Catalytic Products International (CPI)

This Pre-Owned VECTOR 4 is ready for your application! With a capacity of 4,000 scfm and a heat exchanger that can attain up to 67% thermal efficiency, this unit will provide 95% Destruction Rate Efficiency for a low price, and at a low monthly cost as well.

VECTOR - Catalytic Oxidizers

by Catalytic Products International (CPI)

The VECTOR line of catalytic oxidizers is designed to treat hydrocarbons, volatile organic compounds (VOC), hazardous air pollutants (HAP), noxious and odorous emissions. No other manufacturer offers you the extensive knowledge - in both oxidizers and catalyst technologies - necessary to achieve the most complete and cost effective elimination of ...

VECTOR-e - Catalytic Oxidizer

by Catalytic Products International (CPI)

The VECTOR-e line of catalytic oxidizers is based on the success of our VECTOR System with the substation of an electric heating system – rather than a gas combustion system. No other manufacturer offers you the extensive knowledge - in both oxidizers and catalyst technologies - necessary to achieve the most complete and cost effective ...

Need help finding the right suppliers?

Let the XPRTs do the work for you