Waste to Energy Equipment

800 Results found
  • Category: Energy & Renewables ×

  • Subcategory: Waste to Energy ×

Model PR-50 - Plasma Reactor

by High Temperature Technologies Corp. Canada     based in Chateauguay, QUEBEC (CANADA)

Plasma Pyrolysis Reactor PR-50 is used as a basis for the system that treats gaseous, liquid and disperse medical, toxic and chemical waste. Power used by the system is up to 100кW. By products (such as synthesis gas and powder) that are received as a result of the process can be used in other applications. Electric energy generated through ...

Model WT2 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT2 is the entry level unit and a very popular choice for the smaller workshop. The small footprint, ease of installation and being virtually maintenance free make it the obvious choice for workshops up to around 2500ft². Manufactured using the same high quality materials as the larger WT range of heaters means the customer gets ...

Model WT5 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT5 is the smallest of the double pass heat exchange models and is a fully exempt appliance to burn chipboard, MDF, hardwood and softwood off-cuts without the need of a costly afterburner, even in city centres and built up residential areas. With a full refractory lined firebox and highly efficient double pass heat exchange with fully welded ...

Model WT10 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT10 is the middle unit of the double pass heat exchange models and will produce 300,000btu/hr of warm air, enough to heat a workshop of up to 7500ft². Once again the WT10 is fully compliant with the clean air act without an oil or gas afterburner. As with all the WT range these units are the most robust, heavy duty heaters available in ...

Model WT15 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT15 is the largest of the hand fired units and is still the most popular heater in the wood working industry since its launch. The reason for its popularity is, as with the other WT heaters, the robust design, low servicing costs and high heat output Once again the WT10 is fully compliant with the clean air act without an oil or gas ...

Talbott - Model T500 - Wood Burning Heater Reconditioned

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

Talbott T500 (500,000btu/hr) wood burning heater reconditioned.Wood waste heater with new heat exchange, Re-lined firebox, Re-insulated cabinet, Re-wired. 3 month warranty.

Cogeneration

by Montealto     based in Córdoba, SPAIN

Cogeneration technology generates both electricity and usable heat. It is useful in industrial facilities where vapour and/or hot water are needed and, in general, in any facility that uses heat or cold, or in facilities where waste heat can be recovered to generate electricity. In Spain, cogeneration technology, like other renewable energies, ...

BALTEAU - Biogas Collection System

by BALTEAU SA     based in Sprimont, BELGIUM

At landfill sites, the biogas emanating from the biodegradable fraction of waste has to be pumped through a degasification network sited within the mass of waste.

REI - Dump & Run Shredders

by Recycling Equipment Inc. (REI)     based in Newton, NORTH CAROLINA (USA)

REI engineers, designs, manufactures and supports a series of “Dump and Run” Industrial Shredders and Grinders for the most demanding material size reduction applications. These types of shredders allow the user to dump large quantities of scrap into the charge chamber at one time and walk away.

VMpress - Kaiserslautern Plant

by VMpress s.r.l.     based in Ovada, ITALY

The plant in Kaiserslautern is fed with appr. 40,000 t/a of municipal solid waste, but it has been conceived for the treatment of up to 100,000 t in the event that the waste supply area should be extended.Municipal waste is unloaded in the reception area and directly fed into the hopper of extruder press by means of a grab bucket.The extruder ...

Need help finding the right suppliers?

Let the XPRTs do the work for you