Vibration Control Equipment in Romania

Serving Romania | Office in RomaniaNear Romania
496 Results found
  • Category: Health & Safety ×

  • Subcategory: Vibration Control ×

  • Location: Europe ×

  • Location: Romania ×

Vibro - Model Strip - Antivibration Strip

by ALPHA ACOUSTIKI Ltd.     based in Halandri, GREECE

The hemi-cylindrical bearing strip is a non-reinforced elastomeric bearing system. Due to its ingenious profile, the cross-section is suitable for use as an elastic support for structural components.

Model HI 813 - Portable Vibration Shaker

by Hardy Process Solutions     based in San Diego, CALIFORNIA (USA)

Mid-level portable shaker for transducer / accelerometer vibration, verification and calibration. Used for testing from 25 to 10,000 Hz, the Hardy HI 813 Shaker offers adjustable frequency and adjustable vibration level. This provides a reference source for verifying the accuracy of vibration transducers, connectors, cabling and instruments or ...

Accelerometers

by Brüel & Kjær Vibro GmbH     based in Darmstadt, GERMANY

For advice on the correct acceleration sensor and installation accessories, we recommend that you discuss your specific application with our specialists to ensure the correct solution.

PCH - Model 1106 - Vibration Sensor

by PCH Engineering A/S     based in Horsholm, DENMARK

Measuring parameter: Velocity mm/s, Acceleration m/s² or, Displacement mm peak-peak, Frequency range: 10 to 1000 Hz or to be defined, True RMS detector, Output 4-20 mA or 1-6 V DC, proportional to 0-100 %.

Accelerometers

by PCH Engineering A/S     based in Horsholm, DENMARK

In our range of accelerometers we are confident you will find the transducer type, which will fit your application. A transducer has a nominal sensitivity. A Calibration Certificate follows each transducer telling the exact sensitivity, which naturally is within the specified tolerance. Low tolerance transducers can be supplied on request. All ...

Kits for Control of Vibration at Work Regulations

by Castle Group Ltd.     based in North Yorkshire, UNITED KINGDOM

Vibration meter kits and training courses designed for the Control of Vibration at Work Regulations 2005 and similar international vibration measurement legislation. Covering the limits of exposure from tools and equipment, the Control of Vibration at Work Regulations 2005 are a standardised approach to risk assessment from hand-arm vibration ...

Brüel & Kjær - Model Type 4527 - Triax Accelerometer

by Brüel & Kjær Sound & Vibration Measurement A/S     based in Nærum, DENMARK

Designed to operate continuously at 180°C (356°F) to meet the toughest environmental requirements, the wide 0.3Hz to 10 kHz frequency range and low weight of Triaxial CCLD Accelerometer Types 4527 and 4527-001 make them equally suitable for use as general purpose accelerometers. When only a single- or dual-axis measurement is needed, these ...

Model SV 100A - Wireless Whole-Body Vibration Exposure Meter

by Svantek Ltd.     based in Warszawa, POLAND

The new SV 100A is a wireless whole-body vibration exposure meter suitable for whole-body measurements in accordance with ISO 2631-1. Suitable for taking measurements both on the seat and seat-back, the device uses the very latest technology and is ease of use. The instrument is equipped with 4 push buttons and a small OLED display that allows ...

Model SV 150 - Tri-Axial Acceleromete

by Svantek Ltd.     based in Warszawa, POLAND

SV 150 is a tri-axial accelerometer designed to be used with the SV 106 human vibration analyser to provide a dedicated instrument for measurements according to ISO 5349-2. The accelerometer can easily be attached to the handle of the vibrating tool being measured. The sensor's TEDS memory stores information about calibration factor limiting ...

Model Vibro-FM - Wooden Floor Sound Insulation

by ALPHA ACOUSTIKI Ltd.     based in Halandri, GREECE

Vibro-FM is produced based on a deep research in National Τechnical Uniνersity of Αthens. ΤΥΡΕ Α: Simple elastic base. ΤΥΡΕ Β: Consists of metallic strip which needs to be fixed on to a supported floor. The floor pads consist of metallic and elastic parts which are connected ...

Need help finding the right suppliers?

Let the XPRTs do the work for you