Conductivity Monitoring Equipment in Honduras

Served | Office inNear
353 Results found
  • Category: Monitoring & Testing ×

  • Subcategory: Conductivity Monitoring ×

  • Location: Latin America ×

  • Location: Honduras ×

In Situ Hydraulic Conductivity Tests: Hooghoudt model

by Eijkelkamp Agrisearch Equipment     based in Giesbeek, NETHERLANDS

Determination of the water permeability, is important for agricultural- and for environmental soil research. On the basis of the permeability factor (K-factor) irrigation- and drainage systems are designed. Also with respect to the extend of the spreading of possible pollution the permeability factor of the soil is of great importance.

In Situ Hydraulic Conductivity Tests: Rainfall Simulator

by Eijkelkamp Agrisearch Equipment     based in Giesbeek, NETHERLANDS

The extent to which the soil is sensitive to erosion is determined largely by the composition of the soil. Knowledge of the sensitivity to erosion is important for the development of a certain plot. The sensitivity to erosion is hard to measure. Absolute values can not be obtained. It is, however, possible to obtain a reasonable indication by ...

Model WEC/WDEC410 - Toroidal Conductivity Controllers

by Walchem, IWAKI America Inc     based in Holliston, MASSACHUSETTS (USA)

The WEC/WDEC410 Series Single and Dual Input Electrodeless Conductivity Controllers measure conductivity of a solution via an encapsulated, non-contacting sensor to control replenishment pumps and alarms. They may be installed in a variety of very harsh chemical control applications, including oily cleaner baths, chromates, rinse tanks, fume ...

YSI - Model EC 300 - Conductivity/Salinity/Temperature Meter

by Forestry Suppliers, Inc.     based in Jackson, MISSISSIPPI (USA)

This compact, handheld meter measures conductivity, specific conductance, salinity, and temperature. Features include a super-stable four-electrode conductivity cell, calibration back-up, convenient one-hand operation, a user-friendly interface, and a water resistant, splash resistant case (meets IP-65). Two cable lengths available. One-year ...

Oakton - Hand-Held Conductivity/TDS Meter

by Forestry Suppliers, Inc.     based in Jackson, MISSISSIPPI (USA)

This advanced meter simultaneously displays TDS and temperature or conductivity and temperature, ranges for TDS readings automatically, and is able to store one TDS calibration point along with five conductivity calibration points. Selectable read outs as ppm and ppt, or as mg/l and g/l. Probe is 12 mm in diameter and has a 3´ cable. Other ...

Oakton¬ pH/Con 650 Meter with Probe

by Forestry Suppliers, Inc.     based in Jackson, MISSISSIPPI (USA)

Connect a pH or ISE and a conductivity or dissolved oxygen probe at the same time to simultaneously measure your choice of pH, mV, or ISE and conductivity or dissolved oxygen! Other features include datalogging of up to 500 data points with GLP compliance, wireless IrDA communication for truly waterproof interfacing capabilities, user-selectable ...

IC Controls - Model 210-C-TDS - Boiler Water Total Dissolved Solids (TDS) Analyzer

by IC Controls     based in Orangeville, ONTARIO (CANADA)

The Boiler Water Total Dissolved Solids (TDS) Analyzer model 210-C TDS from IC Controls gives you maximum flexibility, reliability, and ease of use. The Total Dissolved Solid measurement are critical to your boiler and must be strictly monitored and maintained to ensure maximum operating efficiency. The 210-C TDS was ...

Vertek - Model HT Series - Electric Conductivity (Resistivity) Module

by Vertek Cone Penetration Test Equipment     based in Randolph, VERMONT (USA)

The HT Series Resistivity Module combines the standard CPT measurements: tip, local friction, inclination and pore water pressure with electrical measurements of the soil. The combination of these parameters provides comprehensive information useful in determining the stratigraphy of the soil and the location of potential ground water problems in ...

Hanna Instruments - Model HI 9033 - Conductivity and TDS Meters

by Pike Agri-Lab Supplies, Inc.     based in Jay, MAINE (USA)

HI 9033 utilizes a single probe to perform all conductivity readings in four ranges. This allows the user to measure samples from deionized water to brine without having to switch or recalibrate the probe.

Model AM Series - Conductivity Sensors

by Water Analytics Inc     based in Andover, MASSACHUSETTS (USA)

AM series cells are made with stainless steel electrodes and body. This insures that, with reasonable maintenance, years of drift-free performance can be expected.

Need help finding the right suppliers?

Let the XPRTs do the work for you