sampling systems Equipment in St. Helena

Served | Office inNear
858 Results found
  • Category: Monitoring & Testing ×

  • Subcategory: Environmental Sampling ×

  • Keyword: sampling systems ×

  • Location: Africa ×

  • Location: St. Helena ×

GDS - Model 306 - Sequential Gas Sampling System 1-20 Way

by GDS Technologies Ltd.     based in West Yorkshire, UNITED KINGDOM

The GDS 306 system is designed to monitor gas levels from a number of sample-points, targeted at situations where the positioning of conventional gas sensors may not be practical. This may be due to equipment security, cable routing, access for detector head installation/maintenance, harsh environment or a cost effective means of monitoring ...

GDS - Model 301 - Single Line Sample Unit

by GDS Technologies Ltd.     based in West Yorkshire, UNITED KINGDOM

Continuous monitoring. Flammable, oxygen or toxic gases. Easily installed and maintained. 2 alarm levels & relays. 4~20mA analogue output. Line blockage and pump fail monitor. Delay to alarm option.

Interface Board (i/fB)

by PPM Technology     based in Caernarfon, UNITED KINGDOM

The PPM Technology interface board (ifB) has been designed to connect the Formaldemeter or Glutaraldemeter to third party systems. The interface board can be configured to give different voltage outputs; a 4–20mA current output and also give a relay alarm output. Various modes of operation are available to suit a whole array of uses, ...

Crowcon - Air Aspirator Sampling Systems

by Crowcon Detection Instruments Ltd     based in Milton Park, UNITED KINGDOM

Designed for use in Zone 1 or Zone 2 hazardous areas, the air aspirated system uses a compressed air driven vacuum generator to draw a gas sample from a single point. Explosion- proof gas detectors are fitted to monitor for flammable gases, toxic gases or oxygen. Each detector provides a 4-20mA output. An intrinsically safe flow-fail device warns ...

Crowcon - Single Point Sample System

by Crowcon Detection Instruments Ltd     based in Milton Park, UNITED KINGDOM

The single point system is designed to monitor gas samples from pipelines or processes. A powerful high-flow pump extracts and transports gas samples to the system where they are conditioned to remove dust and moisture. The conditioned sample gas is then passed across one and four gas sensors before being either exhausted to atmosphere or returned ...

Crowcon - Multi Point Continuous Sample System

by Crowcon Detection Instruments Ltd     based in Milton Park, UNITED KINGDOM

The multi-point system uses the same sampling arrangement as the single point system, but can monitor up to 16 separate sample lines on a sequential basis. The multi-point system provides a cost effective and low maintenance solution for monitoring gas hazards in buildings, pumping stations, storage areas etc. Each sample line is monitored for one ...

Crowcon - Model PGSi - Programmable Sampling System

by Crowcon Detection Instruments Ltd     based in Milton Park, UNITED KINGDOM

The PGSi is a highly versatile system that can monitor up to 32 separate sample lines on a sequential basis. Operating from Windows XP based software, the PGSi system is the ideal solution for monitoring landfill gas in boreholes, or for protecting buildings such as retail parks, hospitals and schools built on landfill sites. The system can be ...

GilAir - Model Plus - Personal Air Sampling Pump

by Sensidyne     based in St. Petersburg, FLORIDA (USA)

Innovation Delivered: The ultimate personal air sampling pump delivering enhanced performance, greater versatility, and superior design and comfort.

HORIBA - Model GPS5 - Gas Sampling System

by HORIBA Europe GmbH     based in Leichlingen, GERMANY

HORIBA gas samplers are suitable for volume-correct taking of gaseous samples during emission and emission measurements. This device can be used wherever gases and gaseous components must be inspected.

Genie - Model 755 - Direct Drive Probe

by a1-cbiss     based in Birkenhead, UNITED KINGDOM

Genie Probes provide a means to insert Genie Membrane Technology directly into a pipeline for the purpose of separating unwanted liquid and particulate from the gas sample at flowing temperature and pressure conditions, in compliance with industry standards. The Model 755 is an adjustable length, membrane tip probe regulator that can be inserted ...

Need help finding the right suppliers?

Let the XPRTs do the work for you