emissions standard Equipment

1170 Results found
  • Keyword: emissions standard ×


Instrumatic CEMS - Continous Emission Monitoring System

by Instrumatic A/S     based in Ry, DENMARK

Instrumatic has since 1985 supplied CEM systems based on dilution extractive sampling in combination with ambient air analyzers. Instrumatic sell the CEM system world wide in cooperation with our partners, direct to endusers and to OEM customers.


Cerex - Model FT5000+ - Continuous Emissions Monitor

by Cerex Monitoring Solutions, LLC.     based in Atlanta, GEORGIA (US) (USA)

Dual channel FTIR / UVDOAS Cross Stack Multi-gas CEM Analyzer. The Cerex FT5000+ is a fixed Continuous Emissions Monitor for cross stack or process applications. The system is based on proven FTIR and UVDOAS technology. The FT 5000 Plus analyzer provides real-time multi-gas qualification and quantification of gases commonly found in stack ...

Model GCEM4100 - Multi Channel Extractive Flue Gas Analyser

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The GCEM4100 is a hot extractive analyser for difficult flue gas monitoring applications. It uses infrared absorption spectroscopy to measure up to seven pollutant species in a single self-contained unit. Many conventional extractive systems require the sampled gas to be cleaned and dried to a very high standard prior to analysis, invariably ...

Model 1010 - Single Channel Cross Duct CO Gas Analyser

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The Model 1010 is a single channel cross-duct analyser for the measurement of CO. It uses an infrared transmitter to project a beam of light across the duct to a receiver mounted opposite. The light beam is tuned to a specific wavelength where the CO molecules absorb the light energy but there is no interference from water vapour and other gases. ...

StakGard - Tribo Electric Indicative Dust Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The StakGard uses the well-proven tribo-electric effect to directly measure mass particulate concentration by sensing the frictional charge created when particles collide with a conductor. The advanced electronics of the StakGard detect this signal and present it to the operator via a modulating LED display. The StakGard indicative particulate ...

Model VCEM5000 - Flue Gas Flow Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

Continuous emission monitoring often only considers the density of the emissions (e.g mg/Nm3) In order to obtain a measurement of total emissions for pollution monitoring (e.g kg/hr) it is necessary to either calculate or measure flow within the gas stream. The VCEM5000 provides non-contact measurement of gas velocity using a time-delay ...

Model DCEM2100 - Dual Pass Opacity / Dust Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The DCEM2100 is a dual-pass transmissometer configured for the continuous measurement of opacity and dust concentration in flue gases. Its unique optical arrangement provides continuous measurements of transmissivity of visible light across the stack in opposite directions, providing not only an accurate average of the dust loading in the stack, ...

Model DCEM2000 - Dual Pass Opacity / Dust Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The DCEM2000 is a dual-pass transmissometer configured for the continuous measurement of opacity and dust concentration in flue gases. Its unique optical arrangement provides continuous measurements of transmissivity of visible light across the stack in opposite directions, providing not only an accurate average of the dust loading in the stack, ...

Model GCEM4000 - Multi-Channel In-Situ Flue Gas Analyser

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The GCEM4000 is a multi-channel flue gas analyser that uses Non-Dispersive Infrared Absorption (NDIR) technology. It provides high accuracy, low maintenance measurement of all the key combustion process emissions to atmosphere. It is capable of operating in very high dust loading conditions, up to several gm/m3 of dust. Its performance can be ...

Model VCEM5100 - Flue Gas Flow Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

Continuous on-line analysis often only considers the density of the emissions (e.g mg/Nm3) In order to obtain a measurement of total emissions for pollution monitoring (e.g kg/hr) it is necessary to either calculate or measure flow within the gas stream. The VCEM5100 provides non-contact measurement of gas velocity using a time-delay correlation ...

Need help finding the right suppliers?

Let the XPRTs do the work for you