emissions standards Equipment in Guinea

Serving Guinea | Near Guinea
1050 Results found
  • Keyword: emissions standards ×

  • Location: Africa ×

  • Location: Guinea ×


Land - Model 4500 MkIII - Opacity and Dust Emissions Compliance Monitor

by Land Instruments International     based in Dronfield, UNITED KINGDOM

The Land Model 4500 MkIII has reset the industry standard on compliance opacity and dust concentration measurement. Combining the unique features of three patented technologies, the 4500 MkIII achieves the highest available specification for the principal performance parameters, as defined by the internationally recognized ASTM Standard D 6216-07.


Opsis - In Situ UV & IR DOAS Systems

by Opsis AB     based in Furulund, SWEDEN

The basic Opsis DOAS system consists of an analyser, an emitter and receiver set, a power supply and a fibre optic cable. The analyser is the central unit in the system. The basic functions are to detect and measure gases and to log data. However, the operation may be varied to meet the particular needs in each application.

Model GCEM4100 - Multi Channel Extractive Flue Gas Analyser

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The GCEM4100 is a hot extractive analyser for difficult flue gas monitoring applications. It uses infrared absorption spectroscopy to measure up to seven pollutant species in a single self-contained unit. Many conventional extractive systems require the sampled gas to be cleaned and dried to a very high standard prior to analysis, invariably ...

Model 1010 - Single Channel Cross Duct CO Gas Analyser

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The Model 1010 is a single channel cross-duct analyser for the measurement of CO. It uses an infrared transmitter to project a beam of light across the duct to a receiver mounted opposite. The light beam is tuned to a specific wavelength where the CO molecules absorb the light energy but there is no interference from water vapour and other gases. ...

StakGard - Tribo Electric Indicative Dust Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The StakGard uses the well-proven tribo-electric effect to directly measure mass particulate concentration by sensing the frictional charge created when particles collide with a conductor. The advanced electronics of the StakGard detect this signal and present it to the operator via a modulating LED display. The StakGard indicative particulate ...

Sierra - Model BG-3 Elite - High Performance Partial Flow Dilution System

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

In use since 2004, BG3 PFD (Partial Flow Dilution) technology effectively performs engine research and development to accurately sample exhaust PM (Particulate Matter) emissions over both steady state and transient test cycles (Read Case Study). On January 7, 2011, PFD was signed into law and is now included in the United States Federal Register ...

Model DCEM2100 - Dual Pass Opacity / Dust Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The DCEM2100 is a dual-pass transmissometer configured for the continuous measurement of opacity and dust concentration in flue gases. Its unique optical arrangement provides continuous measurements of transmissivity of visible light across the stack in opposite directions, providing not only an accurate average of the dust loading in the stack, ...

Model DCEM2000 - Dual Pass Opacity / Dust Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The DCEM2000 is a dual-pass transmissometer configured for the continuous measurement of opacity and dust concentration in flue gases. Its unique optical arrangement provides continuous measurements of transmissivity of visible light across the stack in opposite directions, providing not only an accurate average of the dust loading in the stack, ...

Model VCEM5100 - Flue Gas Flow Monitor

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

Continuous on-line analysis often only considers the density of the emissions (e.g mg/Nm3) In order to obtain a measurement of total emissions for pollution monitoring (e.g kg/hr) it is necessary to either calculate or measure flow within the gas stream. The VCEM5100 provides non-contact measurement of gas velocity using a time-delay correlation ...

Model GCEM4000 - Multi-Channel In-Situ Flue Gas Analyser

by Codel International Ltd     based in Bakewell, UNITED KINGDOM

The GCEM4000 is a multi-channel flue gas analyser that uses Non-Dispersive Infrared Absorption (NDIR) technology. It provides high accuracy, low maintenance measurement of all the key combustion process emissions to atmosphere. It is capable of operating in very high dust loading conditions, up to several gm/m3 of dust. Its performance can be ...

Need help finding the right suppliers?

Let the XPRTs do the work for you