exhauster Equipment in Morocco

Serving Morocco | Office in MoroccoNear Morocco
1670 Results found
  • Keyword: exhauster ×

  • Location: Africa ×

  • Location: Morocco ×

Exhausters With Pre-Inlet

by Aerzener Maschinenfabrik GmbH     based in Aerzen, GERMANY

For pre-inlet cooling the housing is equipped with an additional third socket on the suction side. The lube oil supply is effected by splash oil lubrication. The conveying chamber is sealed by a sealing system. Driving shaft by double radial seal rings with grease barrier. Direction of flow vertically from top to bottom. The drive can be effected ...

HI-Q - Sample & Return Exhaust Lines

by HI-Q Environmental Products Company     based in San Diego, CALIFORNIA (USA)

Many air sampling procedures call for remote site sampling where the vacuum source (air sampling pump) cannot be conveniently located in the same area where sampling is required. This may be due to a variety of reasons including explosive sampling environments, inaccessibility, and noise level restrictions. For this reason, HI-Q has developed two ...

Exhaust Back Pressure Control Valve

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

Our exhaust back pressure control and simulation package centers around our proprietary exhaust back pressure valve, a fast-acting ALL stainless steel butterfly valve controlled by an electronic actuator. The valve adjusts to accurately simulate the effective back pressure of a full vehicle exhaust system, but on a closed test bed ...

Model EGAS 2M - Engine Exhaust Gas Analysis System

by Environnement S.A     based in Poissy, FRANCE

The only system allowing the measurement of 1 or 2 independent streams in a single analysis cabinet. Measurement of THC, NO, NO2, NOx, CO, CO2, O2 and NH3. Designed to measure emissions from all combustion engines regardless of fuel type.

Selective Catalytic Reduction (SCR)

by Clarke Energy     based in Liverpool, UNITED KINGDOM

The Soot Filter, It is known that fine particles of soot produced within an internal combustion engine can have a carcinogenic effect if they become attached to lung tissue. A fibrous soot filter can filter the fine particles from the exhaust gas. The particles are burnt away at operating temperature within the system on the catalyst-impregnated ...

Carbon Dioxide Scrubbers

by Clarke Energy     based in Liverpool, UNITED KINGDOM

Although the utilisation of gas is one of the cleanest types of fuel during combustion there are some trace contaminants in the raw exhaust which would make it unsuitable for the above applications. Typically selective catalysts can be utilised in order to remove different contaminants from the raw exhaust gas.

CL.AIR - Exhaust After-Treatment System

by Clarke Energy     based in Liverpool, UNITED KINGDOM

The CL.AIR Exhaust After-Treatment System for GE’s Jenbacher gas engines is a thermal regenerative post-combustion system for engine exhaust gases. Since no catalytic reactions take place during the thermal treatment of the exhaust, as it is insensitive to impurities in the fuel gas, the CL.AIR system is particularly suitable for use with ...

ExhaustTrak - Model Sierra CP Series - Raw Engine Exhaust Mass Flow Meter

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

Sierra CP has successfully manufactured and sold AirTrak intake air mass flow meters since the early 1990's.  With deep roots in flow measurement through our Flow Division, we have

Waste Exhaust Heat Boilers

by Clarke Energy     based in Liverpool, UNITED KINGDOM

Approximately 25% of the usable energy of the fuel gas is released in the exhaust of the gas engine. This heat exits the engine at ~450oC as ‘high grade heat’, contrasting to ‘low-grade heat’ available from the generator cooling circuits. This high temperature and flow makes it well suited for utilisation in a waste heat ...

Exhaust Gas Heat Exchangers

by Clarke Energy     based in Liverpool, UNITED KINGDOM

Exhaust gas heat exchangers (EGHE) utilise waste heat from the exhaust of the GE Jenbacher gas engine. They are typically located adjacent to the engine or are mounted on the roof of a containerised combined heat and power unit. They are present in a wide range of different applications and along with the other systems can be used to achieve ...

Related Terms for exhauster

Need help finding the right suppliers?

Let the XPRTs do the work for you