flow sensors Equipment in Missouri

Served | Office inNear
2063 Results found
  • Keyword: flow sensors ×

  • Location: USA ×

  • Location: Missouri ×


Dyacon - Model TPH-1 - Temperature, Humidity and Barometric Pressure Sensor (Modbus)

by Dyacon, Inc.     based in Newton, UTAH (USA)

TPH-1 is a digital output air sensor that combines air temperature, relative humidity, and barometric pressure in one sensor device. TPH-1 uses Modbus RS-485 to connect to computers, programmable logic controllers, and some data loggers.The sensor is suitable for use as an outdoor environmental device or for indoor HVAC controls.


SWAN - Model AMI pH-Redox; M-Flow - Complete Analyzer on Mounting Panel

by SWAN Analytische Instrumente AG     based in Hinwil, SWITZERLAND

Monitor for continuous measurement of pH or redox (ORP) in potable water and effluents. Complete system mounted on PVC panel: Transmitter AMI pH-Redox in a rugged aluminum enclosure (IP 66). Flow cell M-Flow 10-3PG with temperature sensor (Pt1000). Factory tested and calibrated. Ready for installation and operation.

Dyacon - Model RGTB-4 - Tipping-Bucket Rain Gauge – Siphon Flow Control

by Dyacon, Inc.     based in Newton, UTAH (USA)

A chrome-plated tipping bucket collects rain in 0.01″ increments. A signal with each tip is sent to attached equipment, such as data loggers or Dyacon Control Modules. RGTB-4 uses a special siphon mechanism to ensure accurate measurements up to 19 in/hr (500 mm/hr).

SWAN - Flowcontroller - Flow

by SWAN Analytische Instrumente AG     based in Hinwil, SWITZERLAND

Sampling accessory to regulate flow with pressure reducing valve including flow measurement. Pressure reducing valve (0-4 bar), maximum inlet pressure 10bar. Flowmeter made of Acrylglas with capillary tube including SWAN Flowmeter (Hallsensor) with 1m cable length. Sample in- and outlets with female threads ⅛' for Serto 8 mm connections.

Motory Aspirated Radiation Shields

by Climatronics Corporation     based in Bohemia, NEW YORK (USA)

Climatronics Motor-Aspirated Solar Radiation Shield, Motor TS-10 (P/N 100325), utilizes a triple-shield design and fan to provide the constant mass flow rate past the sensor(s) necessary to yield accurate temperature values. This shield is superior to a naturally aspirated shield, which relies on the wind conditions for sensor ventilation. ...

Temperature Sensors

by Climatronics Corporation     based in Bohemia, NEW YORK (USA)

Capable of meeting virtually any ambient measurement need, Climatronics’ temperature sensors are accurate durable, and linear over a wide range, can be provided with NIST traceable calibration, and are well matched for high accuracy delta temperature applications. The Air, Water/Soil, and Expanded Range Sensors encase a thermistor bead in a ...

PARTAC Particulate Profiler/Counter Sensor

by Climatronics Corporation     based in Bohemia, NEW YORK (USA)

Climatronics' PARTAC Tactical Particulate Profiler (P/N 102686) is a robust size-selective particulate sampler used as an NBC agent alarm trigger, an ambient monitor for public and work places, and as a ground-truth reference for the verification of standoff particulate detectors. The PARTAC simultaneously monitors airborne particle counts in up ...

SWAN - Model B-Flow SS316L L130 - Flow Cell for the Connection to Tubes for One Sensor

by SWAN Analytische Instrumente AG     based in Hinwil, SWITZERLAND

Flow cell for the connection to tubes for one sensor with ¾' NPT thread. Made of stainless steel (SS316L).

SWAN - Model B-Flow SS316L OTG - Pressure-Resistant Flow Cell for Oxytrace G Sensor

by SWAN Analytische Instrumente AG     based in Hinwil, SWITZERLAND

Pressure-resistant flow cell for Oxytrace G sensor made of stainless steel.

SWAN - Model B-Flow IS1000 - Stainless Steel Flow Cell for two Sensors

by SWAN Analytische Instrumente AG     based in Hinwil, SWITZERLAND

Stainless steel flow cell for two sensors with integrated temperature probe. Flow cell for two PG13.5 sensors with built-in Pt1000 temperature probe. Suitable for all sensors with PG13.5 screw head and a max. shaft length of 120 mm. Connection to tubes with selectable Swagelok fittings.

Related Terms for flow sensors

Need help finding the right suppliers?

Let the XPRTs do the work for you