oil water separators Equipment in Finland

Served | Office inNear
1048 Results found
  • Keyword: oil water separators ×

  • Location: Europe ×

  • Location: Finland ×

Oil / Water Separator

by WesTech Engineering, Inc.     based in Salt Lake City, UTAH (USA)

Designed according to API 421, WesTech API Oil / WaterSeparators combine state-of-the-art separation, skimming and sludge transport technologies into a highly efficient primary oil separation device.

EnviroSEP - Oil And Water Separator

by Ovivo (Formerly Eimco Water Technologies)     based in Salt Lake City, UTAH (USA)

Ovivo’s EnviroSEP units provide oil and water separation for a multitude of industrial wastewater, process water pre-treatment and stormwater treatment applications. The unit is designed to remove all free oil from contaminated streams to comply with the most stringent of discharge requirements. Typically, no more than 5mg/l of oil will ...

Model 2852-OWS - Oil/Water Separator & Sump Alarm

by Arjay Engineering Ltd.     based in Oakville, ONTARIO (CANADA)

The sensing probe continuously monitors for the oil/water interface in a water filled sump or separator. It is typically used to control pumps, operate valves, or activate alarms. The 2852-OWS sensing probe monitors the capacitance field around the active probe tip. As the volume of separated oil increases in the separator or is drawn down toward ...

Oil/Water Separator for Liquid Separation

by Geotech     based in Leamington Spa, UNITED KINGDOM

The high capacity cost effective low maintenance compact oil water separators utilise a highly efficient coalescing media pack. The separators are fully automatic, involve no moving parts and can be supplied for flows up to 60 lpm.

Model 4100-OWS - Oil/Water Separator Level Monitor

by Arjay Engineering Ltd.     based in Oakville, ONTARIO (CANADA)

This unique oil level system provides complete flexibility for monitoring oil water separators in one complete package. The 4100-OWS sensing probe monitors the capacitance field between the probe and the concentric shield. As the oil accumulates and displaces the water, the probe capacitance changes. This interface signal is used to provide ...

MPPE & TiPSS - Model CPI - Corrugated Plate Interceptor for Oil-Water Separation

by MPPE & TiPSS Technology – Veolia Water Technologies     based in Ede, NETHERLANDS

The CPI is the basic TiPSS unit mainly used for oil-water separation. The CPI holds modular-counter-current-flow plate packs executed in GRP or Stainless Steel. The CPI basin can be executed in concrete or steel. The concrete units are specifically suited to integrate with sewer systems below ground level so that a gravity flow can be used. The ...

Model pCPI - Pressurized Cross Flow Interceptor for Oil-Water Separation

by MPPE & TiPSS Technology – Veolia Water Technologies     based in Ede, NETHERLANDS

The TiPPS CPI Pressurized is applied when the oil (or any non water miscible organic fluid) and solids contaminated feed water is pressurised or a fully contained plate pack is required (offshore).

Oxymat - Oil and Water Separators

by Oxymat - Oxygen Generators     based in Helsinge, DENMARK

All compressors produce a condensate with hazardous waste of oil and dirt. This condensate must be treated with care. The product is polluted and must not be led out in the sewage or on the floor. The contaminated water should be collected in an Oil and Water separator. The separator will separate the condensate into water and oil through a secure ...

Oil and Fuel - Viledon pluratexx

by Freudenberg Filtration Technologies SE & Co. KG     based in Weinheim, GERMANY

Filtration media play a critical role in the efficiency and reliability of modern automotive engines. Engineered nonwovens surpass the performance and lifetime of cellulose papers, which are traditionally used in oil and fuel filters. Freudenberg’s new pluratexx oil filter media are a quantum leap in engine oil filtration. Made from 100% ...

Model VTC Series - Oil Water Separators

by AFL industries     based in Riviera Beach, FLORIDA (USA)

The VTC removes hydrocarbons and settleable solids from industrial wastewater and coolant. In operation, this separator accepts industrial liquid waste in the inlet chamber. Here settleable solids fall to the bottom as sludge for periodic removal.

Need help finding the right suppliers?

Let the XPRTs do the work for you