wood waste Equipment in Finland

Serving Finland | Office in FinlandNear Finland
940 Results found
  • Keyword: wood waste ×

  • Location: Europe ×

  • Location: Finland ×

C. F. Nielsen - Wood Waste Briquetting Planing Plant - 2800 kg/h Capacity

by C. F. Nielsen A/S     based in Baelum, DENMARK

This case shows a 3-shift briquetting plant installed in a major Swedish planing factory to deal with the wood waste as it occurs. The briquetting line has a capacity of 2800 kg/h of softwood briquettes from the available production waste. It includes two BP 5500 briquette presses placed under a deck in the lower part of a large storage silo.

Model BC 3000 - Wood Chipper

by Farmi Forest Corporation     based in IISALMI, FINLAND

FARMI BC 3000 makes crane feeding more efficient and easy. It works well with slabs, tree trunks without branches and with short wood waste. BC 3000 is as an optional accessory for CH 260 HF-EL and HF-EM models. Conveyor replaces the standard hopper and it has its own hydraulics connected to chipper. Conveyor comes with 2 wheels, which makes ...

Model WT2 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT2 is the entry level unit and a very popular choice for the smaller workshop. The small footprint, ease of installation and being virtually maintenance free make it the obvious choice for workshops up to around 2500ft². Manufactured using the same high quality materials as the larger WT range of heaters means the customer gets ...

Model WT10 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT10 is the middle unit of the double pass heat exchange models and will produce 300,000btu/hr of warm air, enough to heat a workshop of up to 7500ft². Once again the WT10 is fully compliant with the clean air act without an oil or gas afterburner. As with all the WT range these units are the most robust, heavy duty heaters available in ...

Model WT5 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT5 is the smallest of the double pass heat exchange models and is a fully exempt appliance to burn chipboard, MDF, hardwood and softwood off-cuts without the need of a costly afterburner, even in city centres and built up residential areas. With a full refractory lined firebox and highly efficient double pass heat exchange with fully welded ...

Model WT15 - Wood Waste Heater Unit

by Wood Waste Technology Ltd     based in Stafford, UNITED KINGDOM

The WT15 is the largest of the hand fired units and is still the most popular heater in the wood working industry since its launch. The reason for its popularity is, as with the other WT heaters, the robust design, low servicing costs and high heat output Once again the WT10 is fully compliant with the clean air act without an oil or gas ...

ERS - Green and Wood Waste Grinders

by Eco Recovery Systems Inc     based in St. George, UTAH (USA)

Our grinders offer consistent material sizing and processing rates that are the highest in the industry! Whether you compost or produce reusable bi-products from green waste, you can depend on our grinders to increase production and keep your operation consistent.

Valmet - Model WoodSaver - Roll Conveyor System

by Valmet Corporation     based in Espoo, FINLAND

WoodSaver is a special roll conveyor system designed to maximize wood-usage efficiency in debarking lines. The system saves wood by separating usable wood pieces from the bark line and returning the recovered wood back to the process, instead of burning them as waste together with the bark. WoodSaver can also be installed in existing lines to ...

ACTA - Wood Waste Crusher

by ACTA Recycling ApS     based in Odense, DENMARK

Why is the ACTA Crusher used for crushing Wood Waste Crushed Wood Waste is often used as fuel chips/briquettes or as 'new' raw material for chip board production. Due to the fact that wood waste contains a lot of foreign items such as nails, screws, brackets etc. it is a must that the wood waste is pre crushed before entering into a fine shredder. ...

Model GHZ T, L, B - Horizontal Wood Waste Shredders

by GROSS Apparatebau GmbH     based in Heilbronn, GERMANY

GHZ series shredders are especially used for shredding longer wood waste. The material is fed to the rotor horizontally through a hopper, roller feed, or vibrating channel feeder. Because of their compact design, GHZ series shredders can be used directly next to wood processing machines such as strip or plate saws. The material to be shredded is ...

Need help finding the right suppliers?

Let the XPRTs do the work for you