We couldn't find any geotechnical instruments equipment suppliers or service providers located in Vietnam
Here is a list of equipment results with suppliers serving Vietnam
Geotechnical Instruments Equipment Available In Vietnam
-
Manufactured by Durham Geo Slope Indicator (DGSI) - part of Nova Metrix LLCbased in USA
A real-time alternative to the traversing probe type of inclinometer, the GeoFlex system is a string of closely spaced MEMS sensors that employs a chain of sensors and does not require an on-site operator. It is ideal for data logging and real-time, remote monitoring for critical applications such as construction ...
-
Manufactured by Durham Geo Slope Indicator (DGSI) - part of Nova Metrix LLCbased in USA
Typical applications of the DGSI Wireless Tiltmeter ...
-
Manufactured by Geonor ASbased in NORWAY
The P-520N frequency counter is the read-out instrument for all GEONOR vibrating-wire transducers. The counter is designed for use in situ and is enclosed in a rigid aluminium housing. The display shows the frequency of vibration in 0.1 Hz. which has to be calculated to physical units using a calibration table. It is powered by a rechargeable 12 ...
-
Manufactured by Geonor ASbased in NORWAY
The Geonor M-600 series piezometers are vibrating wire sensors which are installed by pushing into soft and loose soils without having to drill a borehole. As with all other Geonor vibrating wire piezometers, the M-600 series offer the maximum reliability available for continuous pore water pressure or ground water level measurements. Geonor *s unique design combined with continued technical ...
-
Manufactured by Geonor ASbased in NORWAY
P-430 is a steel reinforced 2-pair cable. It is specially designed to withstand high loads in terms of tension and compression and is protected against water ingress, in case of damaged ...
-
Manufactured by Geonor ASbased in NORWAY
The Geonor M-610 scries arc vibrating wire piezometers used for direct burial in embankments and earth/rockfill dams, for placement in boreholes, and for water level monitoring in open wells, tanks, and open bodies of ...
-
Manufactured by Geonor ASbased in NORWAY
M-603 is a special version of M-600 which is open to the atmosphere and equipped with a rubber membrane above the pressure membrane. Compressed air assistance provides a back pressure in order to relieve the pressure membrane. This will balance the back pressure during push-in penetration and the piezometer will be pressed down more quickly. Back pressure can also be used to relieve the membrane ...
-
Manufactured by Geonor ASbased in NORWAY
The piezometer can be pressed down without pre-drilling, normally until approximately 30 m depth. Intended for Ø32 mm extension tube. Adapters to 1' water pipe can be ...
-
PremiumManufactured by Gouda Geo-Equipment B.V.based in NETHERLANDS
Seismic cone penetration testing (SCPT or SCPTu) is an accurate and reliable geotechnical instrument and system used to determine low strain in-situ compression (P) and shear (S) wave velocity profiles. Our seismic CPT system is made for the international ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
The Innovative Geotechnical Instrumentation's Vibrating Wire Readout Model digilog 1 has been designed to read most commercially available vibrating wire sensors with resonant frequency range of 400Hz to 6000Hz. It also has an inbuilt readout for temperature sensors (thermistors) which are often incorporated within most vibrating wire ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
DIGI View Vibrating Wire readout Units With Engineering units dilsplay is a micro Controller Based indicator for use with Innovative Geotechnical Instrumentataion ' range of vibrating wire transducers. It displays the measured frequency in terms of frequency, time period, frequency squared or the value of measured parameter directly in ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
The model IG 1401 piezometer consists of a rigid cylindrical housing, of diameter 20mm having the innovative vibrating wire sensor inside. The vibrating wire sensor element is completely isolated from the total stresses acting on the body by the help of O rings. The unique design gives a slimline body which accurately reads water pressure without being affected by the surrounding stresses. The ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
straingauges are used to moniter strains in soil, concrete or on steel structures. straingauges can mesure both compresive and tensile ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
These are used for measurement of total pressure in earth fills and embankments, at the interface of two different materials or measurement of stress in concrete. Also used for measurement of contact pressures on retaining walls, piles and tunnel linings. These cells consist of circular stainless steel plates, welded together around their periphery and spaced apart by a narrow cavity filled with ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
These are vibrating wire load cells provided with a swivelling top plate and fixed bottom plate. Number of vibrating wire sensors is generally three. These are used in mines for monitoring load during and after excavation. A beam is provided between the swivel top of the load cell and the roof. The load cell is positioned at the floor along with the convergence meter. Provision of gas discharge ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
These are rugged and compact sensors used to measure loads in tiebacks, rockbolts, struts or tunnel supports. These are designed to meet the demands of the severe and adverse environmental conditions usually associated with construction or mining activities. To monitor tensile load, the load cell assembly has an annular configuration to enable the passage of anchor through it. To monitor ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
IGI Bore Hole stress meter consists of a capsule having length 40mm and diameter 30mm. It has a hollow, steel cylindrical body having a vibrating wire tensioned across one diameter. The perpendicular diameter is wedged tightly inside a diamond drilled bore hole in the rock/ coal by a wedge platen ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
Shotcrete stress cells are designed to measure radial and tangential stresses in shotcrete linings in tunnels. This instrument provides the most significant data for determining thickness and stability of shotcrete lining in NATM (New Austrian Tunneling method). These cells consist of two rectangular stainless steel plates, welded together ...
-
Manufactured by Innovative Geotechnical Instrumentationbased in INDIA
Innovative displacement transducer model IG-1002 is ideal for use in single and mutipoint bore hole extensometers. Its unique slimline design is very convenient for multipoint bore hole extensometers as a number of sensors may be installed within a single hole. The sensor also finds application in soil extensometers and roof convergence measurement. It may even be used as a joint meter in some ...
-
by Detektiabased in SPAIN
Deformation monitoring of dams is key to avoid catastrophic loss of infrastructure and lives. Measuring and monitoring the deformations of these assets is a mandatory task due to the high risk they represent. These monitoring activities are usually based on geotechnical instruments (e.g., direct and inverted pendulum, inclinometers, ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you