Geophysics Equipment in Slovenia

Served | Office inNear
177 Results found
  • Category: Soil & Groundwater ×

  • Subcategory: Geophysics ×

  • Location: Europe ×

  • Location: Slovenia ×

Cone Penetration Testing (CPT) Tests

by Pagani Geotechnical Equipment s.r.l.     based in Calendasco, ITALY

The CPT test (mechanical type) is essentially the extent of resistance to opening up a bit of size and mechanical characteristics standardized, stuck in a land-speed constant (2 cm / sec). In Cone Penetration Testing, with the Begemann Mechanical Cone, the Qc (tip resistance) and RL (side friction) values are measured with a load cell and ...

Vertek - Model S4 - 20 Ton Cone Penetrometer Push System for Skid Steers

by Vertek Cone Penetration Test Equipment     based in Randolph, VERMONT (USA)

The S4 Push System Ensures Simple, Affordable Entry into the CPT Market. Increase your revenue opportunities and see ROI in about 40 days. Have you been thinking about the expanding into CPT, but are concerned about cost or complexity? Vertek’s S4 CPT Push System and highly experienced staff can get you into the market quickly and ...

AMS - Dynamic Cone Penetrometer

by Art’s Manufacturing and Supply, Inc. (AMS Inc.)     based in American Falls, IDAHO (USA)

The most widely accepted, portable method for evaluating strength and density of soil, in situ. The dynamic cone penetrometer uses a 15 lb. (6.8 kg) drive mass falling 20 in. (50.8 cm) that strikes the anvil to cause penetration of 1.5 in (3.8 cm) diameter cone (45 degree vertex angle) that has been seated in the bottom of a pre-augered hole. The ...

AGCOS - Model MARY-24 - Multifunction Low-Frequency Geophysical EM Receiver

by Advanced Geophysical Operations and Services Inc. (AGCOS)     based in North York, ONTARIO (CANADA)

Measuring instrument MARY (Multifunctional receiver for electrical and electromagnetic prospecting) represents the newest development in the field of creation of the portable geophysical equipment. Compactness and simplicity of use of the device are combined with opportunities which until recently were inherent in only large-sized ...

Geonics - Model EM-34-3 - Electromagnetic Land Geophysical Equipment

by Geomatrix Earth Science Ltd     based in Leighton Buzzard, UNITED KINGDOM

The EM34-3 is a fast, simple to operate, cost-effective instrument for the engineering geophysicist, geologist and hydro geologist alike and has been particularly successful for mapping deeper groundwater contaminant plumes and for groundwater exploration.

Geonics - Model EM38-MK2 - Electromagnetic Land Geophysical Equipment

by Geomatrix Earth Science Ltd     based in Leighton Buzzard, UNITED KINGDOM

The EM38 is designed to be particularly useful for agricultural surveys measuring soil salinity, and can cover large areas quickly without needing grounded electrodes. Based on the same patented induction principle as the EM31, the EM38 provides depths of exploration of 1.5 meters and 0.75 meters in the vertical and horizontal dipole modes ...

Geonics - Model G-TEM - Modular TDEM System

by Geomatrix Earth Science Ltd     based in Leighton Buzzard, UNITED KINGDOM

The Geonics G-TEM is a modular TDEM system offering advanced quality control and analysis features to assist operators obtain reliable near surface resistivity soundings. Through incorporating a Laptop PC into the receiver the G-TEM enables the operator to integrate GPS positioning to aid layout and accurately record each sounding location. In ...

Iris - Model Promis - Multi Frequency EM System

by Geomatrix Earth Science Ltd     based in Leighton Buzzard, UNITED KINGDOM

The Promis is a modern implementation of the Slingram technique which uses a coil to produce a primary magnetic field, this is linked by a cable to a receiver sensor at distances between 20 and 200m. The receiver coil measures 3 in-phase components and one out of phase component of the secondary magnetic field induced by ground conductors. ...

Geotech - Cone Penetration Test - CPT

by Geotech AB     based in Askim (Gothenburg), SWEDEN

The Geotech CPT probes are equipped with individual sensors for point resistance (qc), sleeve friction (fs), pore pressure (u) and a tilt sensor. The data measured by the sensors is digitised, multiplexed and encrypted with an error detecting code in the probe before it is forwarded to the transmitter or cable adapter for transmission to the ...

Model GGT-10 - Geophysical Transmitter

by Zonge International     based in Tucson, ARIZONA (USA)

Broadband, constant-current, time and frequency domain, medium-power geophysical transmitter.

Need help finding the right suppliers?

Let the XPRTs do the work for you