Waste Monitoring Equipment

384 Results found
  • Category: Waste & Recycling ×

  • Subcategory: Waste Monitoring ×

Efconomy Sampler

by Siris Environmental Limited     based in Seaham, UNITED KINGDOM

Housed in its own robust dual wall container our EFCONOMY outdoor or indoor use vacuum sampler offers all the benefits and features needed to the meet the demands of the water industry. A 2 year warranty is included and the external cabinet shell is guaranteed for up to 10 years.

Landfill Gas Collection Systems

by Automatic Flare Systems Limited (AFS)     based in Coventry, UNITED KINGDOM

Anaerobic decomposition of organic solid waste in the landfill site produces landfill gas (LFG). LFG mainly consists of methane and carbon dioxide, both of which are odorless. Trace constituents of other volatiles, often malodorous or toxic gases, are also found in LFG. LFG can migrate through soil into structures located on or near landfills. ...

Polyethylene Coliwasa Samples Liquid Waste

by BASCO     based in University Park, ILLINOIS (USA)

Simple design for rapid sample collection. Lower tube to desired depth. A light tug on cord while raising the unit sets the check valve, trapping the sample inside. Plastic rod inside tube allows sample to be collected at any depth. Dispenses easily into appropriate container. Sampler holds approximately 3 ounces per foot.

Blackburn - Model Coliwasa - Composite Liquid Waste Sampler

by Blackburn Sampling, Inc.     based in Galesburg, ILLINOIS (USA)

Use Blackburn Coliwasa to take representative samples of hazardous wastes, liquids, slurry-type sludge's and semi-solids from top to bottom of buckets, barrels, tanks or tankers. Also great for Q. A. and process sampling.

Blackburn - Coupler Sets for Waste Sampling

by Blackburn Sampling, Inc.     based in Galesburg, ILLINOIS (USA)

Assemble rod and tubes for deeper sampling needs. Coupler sets are intended for joining two sampler units only. Any two of the five standard sampler models may be joined. The joining of three lengths is possible but is not recommended for hazardous materials.

Model WAM-100 - Waste Assay Monitor

by VF, a.s.     based in Černá Hora, CZECH REPUBLIC

'Waste-Scan' WAM-100 monitors are used for spectrometric characterization of radioactive waste. It can be used in nuclear power plants, waste repositories, science facilities, reprocessing plants etc. typically for LLW measurements or free release.

Voss SingleSample - Model CW-01 5 - Coliwasa

by Voss Technologies, Inc.     based in San Antonio, TEXAS (USA)

The Voss SingleSample Coliwasa is constructed entirely of inert HDPE to resist almost all chemicals and solvents. The positive displacement, rod controlled valve (shown outside of the device above) features a set of four clamping fingers to assist in holding the valve shut until you are ready to transfer your sample to a container for transport.

Voss SingleSample - Model CW-01 6 - Coliwasa

by Voss Technologies, Inc.     based in San Antonio, TEXAS (USA)

The Voss SingleSample Coliwasa is constructed entirely of inert HDPE to resist almost all chemicals and solvents. The positive displacement, rod controlled valve (shown outside of the device above) features a set of four clamping fingers to assist in holding the valve shut until you are ready to transfer your sample to a container for transport.

Voss SingleSample - Model CW-01 6.5 - Coliwasa

by Voss Technologies, Inc.     based in San Antonio, TEXAS (USA)

The Voss SingleSample Coliwasa is constructed entirely of inert HDPE to resist almost all chemicals and solvents. The positive displacement, rod controlled valve (shown outside of the device above) features a set of four clamping fingers to assist in holding the valve shut until you are ready to transfer your sample to a container for transport.

Voss SingleSample - Model CW-01 7 - Coliwasa

by Voss Technologies, Inc.     based in San Antonio, TEXAS (USA)

The Voss SingleSample Coliwasa is constructed entirely of inert HDPE to resist almost all chemicals and solvents. The positive displacement, rod controlled valve (shown outside of the device above) features a set of four clamping fingers to assist in holding the valve shut until you are ready to transfer your sample to a container for transport.

Need help finding the right suppliers?

Let the XPRTs do the work for you