impeller pump Equipment in Turkey

Serving Turkey | Office in TurkeyNear Turkey
495 Results found
  • Category: Water & Wastewater ×

  • Subcategory: Water & Wastewater Pumps ×

  • Keyword: impeller pump ×

  • Location: Europe ×

  • Location: Turkey ×

Model 4 S4 YD - 1.2m³/h-4.2m³/h - Floating Impeller Pump

by DELTA CABLE     based in Alsancak, TURKEY

Standard Features: Diffuser and Impeller: fiber glass reinforced. Outlet and Suction: Stainles Steel Casting. This pumps can work in min 4' drilling well (100mm).. Max. Sand Content 25 gr/m³. 0.5m³/sa - 21m³/sa'These Pumps can supply water from.

Model 4 S4 YE - 1.8m³/h-5.4m³/H - Floating Impeller Pump

by DELTA CABLE     based in Alsancak, TURKEY

Standard Features: Diffuser and Impeller: fiber glass reinforced. Outlet and Suction: Stainles Steel Casting. This pumps can work in min 4' drilling well (100mm).. Max. Sand Content 25 gr/m³. 0.5m³/sa - 21m³/sa'These Pumps can supply water from.

Model 4 S4 YB - 0.3m³/h-3m³/h - Floating Impeller Pump

by DELTA CABLE     based in Alsancak, TURKEY

Standard Features:  Diffuser and Impeller: fiber glass reinforced. Outlet and Suction: Stainles Steel Casting. This pumps can work in min 4' drilling well (100mm).. Max. Sand Content 25 gr/m³. 0.5m³/sa - 21m³/sa'These Pumps can supply water from.

Chemineer Impeller - Model P-4 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A reasonably cost effective impeller in both turbulent and laminar flow. Good impeller for applications where the viscosity changes over a wide range causing the flow regime to vary between turbulent and laminar flow. A reasonably cost effective impeller for solids suspension.

Chemineer - Model S-4 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A cost effective impeller for operation very near the floor of a tank for agitating the heel in solids suspension applications. Also an effective impeller in laminar flow applications, especially when impeller Reynolds numbers drop below 50.

Chemineer - Model JT-2 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The JT-2 Impeller has been developed for superior blending in transitional flow. Higher viscosity and non-Newtonian fluids make blending much more challenging. This impeller is used after conventional turbines have lost efficiency due to viscous effects and before the need for close clearance impellers.

Chemineer - Model RL-3 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The Chemineer RL-3 impeller is designed for applications where a ragless agitator is desired to prevent fibrous material build-up on the rotating impeller. Typical in Waste Treatment applications the RL-3 is a rag shedding impeller which prevents build-up of fibrous materials on the impeller, while providing a strong axial flow for efficient ...

Model PLN 403 - 4` Plastic Impeller Pump

by Polmot Motor Mak.San. ve Tic. A.S.     based in Selcuklu /Konya, TURKEY

Max. Sand Content: 50 gr/ m3. Frequency: 50 Hz. Rotation: CCW. Rotational Speed: 2900 rpm. Max. VVater Temp.: 30°C. Max. Start / Hour: 4' -10.

Model PLN 618 - 6` Plastic Impeller Pump

by Polmot Motor Mak.San. ve Tic. A.S.     based in Selcuklu /Konya, TURKEY

Max. Sand Content 40 gr/ m3. Frequency 50 Hz. Rotation CCW. Rotational Speed 2900 rpm. Max. VVater Temp. 30°C. Max. Start / Hour 4' - 10 / 6' - 20.

Prochem Maxflo - Model Mark II & III - Impeller Pumps

by National Oilwell Varco     based in Dayton, OHIO (USA)

High efficiency, high solidity impellers for use in turbulent side entering applications. They are especially effective for fluids possessing a yield value, such as paper stock. The high solidity permits operation nearer the boiling point without cavitation.

Need help finding the right suppliers?

Let the XPRTs do the work for you