Air & Climate Applications in Europe

  • Premium

    Formaldehyde and Acetaldehyde Determination in Air Using Fully Automated On-Line Desorption and Analysis of DNPH Cartridges

    Airborne aldehydes and ketones are collected by passing air through a cartridge containing 2,4-dinitrophenylhydrazine (DNPH). Carbonyl compounds react with the DNPH to form hydrazones, which are immobilized on the cartridge. These compounds can be easily eluted from the cartridge with acetonitrile and analyzed by HPLC with UV detection. Traditionally, this analysis including the workup contains a series of manual steps, which can become time-consuming and could incur experimental error. Automating the extraction...

    By Merck KGaA, Darmstadt, Germany based in Darmstadt, GERMANY.

  • Premium

    Analysis of Isocyanates Using the ASSET™ EZ4-NCO Dry Sampler

    Isocyanates are used as a raw material to produce a number of products . Personal exposure can occur while the products made with isocyanates are being applied, or when the materials are removed by grinding or thermal degradation. Workers who are exposed to these compounds are at risk for respiratory disorders and asthma. The highly reactive nature of the isocyanate compounds and the low occupational exposure limits put high demands on both sampling and analytical techniques for monitoring of isocyanates in...

    By Merck KGaA, Darmstadt, Germany based in Darmstadt, GERMANY.

  • Premium

    radiello™ Passive Sampler as a Tool for the Measurement of Atmospheric Ammonia Concentrations and Dry Deposition

    The radiello ammonia sampler impregnated with phosphoric acid represents a low-cost, reliable and simple tool for assessing the atmospheric deposition of ammonia at parts per billion (ppb) concentration levels.

    By Merck KGaA, Darmstadt, Germany based in Darmstadt, GERMANY.

  • Premium

    Capabilities of the Adsorbent Tube Injector System (ATIS™)

    The Adsorbent Tube Injector System (ATIS) was developed at Supelco® by R&D Scientists, as a tool to assist in our comprehensive adsorbent research for thermal desorption tubes. The ATIS provides an efficient means of transferring calibration standards in either the gas or liquid phase onto the adsorbent packed tubes. The ATIS employs the technique of flash vaporization to vaporize the sample in a continuous flow of inert gas; the inert gas carries the sample to the tube. The sample pathway of the ATIS is construct...

    By Merck KGaA, Darmstadt, Germany based in Darmstadt, GERMANY.

  • Premium

    Analysis of Methylimidazoles in Caramel Colored Carbonated Beverages

    Caramel colorings are used as additives in a broad range of food and beverage products to impart a desired color, but have no nutritional or preservative function. Recently, the potential hazard to humans of ammonia- and ammonia-sulfite-process caramel colorings was raised, because they contain the by-product 4-methylimidazole, which is a potential carcinogen.1 The methylimidazole compounds are difficult to analyze due to their polar nature and low molecular weight. Traditional reversed phase techniques are...

    By Merck KGaA, Darmstadt, Germany based in Darmstadt, GERMANY.

  • Premium

    Continuous emissions monitoring for brick plants

    Process control and emissions monitoring in a brick plant is a challenge due to the high concentrations of HF. The HF is generated in the process and gas phase HF can reach 50 mg/m3 or more. To use an extractive system in this environment will demand a lot of maintanence.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Ambient air quality monitoring solutions for PM2.5/PM10 particulate monitoring

    OPSIS provides real-time, flexible monitoring of particulate matter in the ambient air. Particulate matter monitoring with OPSIS, is a cost-effective solution, is ideally suited for use in modern monitoring stations. It can be remote controlled and includes automatic calibration, features that frees time. The SM200 meets the new regulation for automatic monitoring of PM10 and PM2.5. It also meets the new regulation for particulate matter sampling on filter membranes for further analysis of cadmium, nickel, PAH...

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for glass manufacturing industries

    Process control and emissions monitoring in a glass manufacturing plant is a challenge due to high temperature in the flue gas. The OPSIS DOAS system provides the glass industry with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method that uses an optical path to measure across the duct. A single OPSIS system will measure all relevant gas componensts such as NOX, SO2, CO, CO2, H2O, O2, and others.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for mercury monitoring

    Waste incinerators, cement plants and power plants need good and reliable measurements of total gaseous mercury. The measurement of total gaseous mercury is a challenge due to chemical reactions and contamination. The installed systems will often require a lot of maintanence still not giving reliable results.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for mining & smelting

    OPSIS non-contact monitoring solutions, based on either DOAS or TDL techniques, are very well suited for applications in the mining and smelting Industries, as the flue gas conditions often involve high temperatures and high dust concentrations.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Emissions Monitoring for Chemical Plants

    The Opsis gas monitoring system is designed for monitoring in stacks and gas ducts in chemical industries, both in order to increase plant efficiency and to monitor emissions. The Opsis systems have been internationally approved by e.g. the German TÜV and the U.S. EPA.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Emissions Monitoring

    The Opsis monitoring solution in aluminium smelters is based on either DOAS or laser diode technique. The on-line, open-path systems are used for monitoring HF and sulphur dioxide in potrooms, in fence-line applications and in continuous emissions monitoring. Opsis has long experience of monitoring in aluminium smelters.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Air Quality Monitoring Stations

    Opsis provides complete AQM stations, used for street-level, urban trend and background applications. The monitoring systems have been approved by the German TÜV and the U.S. EPA among others.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Ambient air quality monitoring solutions for tunnel monitoring

    Car tunnels need ventilation in order to keep air pollution below the limits. When the pollution levels reaches a setpoint, the fans must be started and kept running until the pollution levels decreases.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for cement industry

    Process control and emissions monitoring in cement plants, can be a challenge due to the dusty and corrosive environment. OPSIS provides an accurate system that will operate with high performance and a minimum of maintenance.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for palm oil plants

    Make more out of your mill. OPSIS tested and approved monitoring systems provide cost-effective and reliable on-line monitoring of several gas compounds, such as both high and low concentrations of methane, moisture, carbon dioxide and hydrogen sulphide, at several locations.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Marine monitoring solutions for the SO2/CO2/NOx monitoring

    Process control of a SO2 scrubber on a ship is a challenge due to wet and corrosive gases. In such environment, extractive gas sampling systems require high levels of maintenance in order to operate correctly. OPSIS monitoring system solves this by using an optical, non-contact, cross-duct technique. A light beam is sent across the duct or stack to be measured, and the captured light is sent through an optical fibre cable to an analyser. The analyser measures SO2, CO2 and NOx concentrations using UV and IR...

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Ambient air quality monitoring solutions for fence-line monitoring

    The OPSIS open-path monitoring system is an excellent tool for monitoring the air quality, fugitive emissions and gas leaks at industrial sites. By arranging monitoring paths strategically at locations outside the borderline of an industrial area, fugitive emissions and gas leaks will effectively be detected. By combining the measured gas data with meteorological parameters information such as where the pollution sources are located and the strength of the emissions can be calculated, using the EnviMan software....

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Emissions Monitoring for Steel Mills

    Steel mills include a multitude of activities that generate gaseous emissions. Besides continuous emissions stack monitoring, the applications in a steel mill also include process mesaurements that provides important data to the operators in order to optimize the steel making process.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Particulate Monitoring

    The Opsis SM200 is a combined particulate monitor that can be used for both automatic measurement and filter sampling. It uses 47 mm filters for sampling and beta attenuation of particulates.

    By Opsis AB based in Furulund, SWEDEN.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you