particulate oxidation catalyst Articles

  • Recuperative oxidizer - Boat engine manufacturer

    Epcon has extensive experience in designing and building Thermal Oxidizers for Engine Cell Testing. The Problem A major Boat Engine manufacturer needed to lower emissions from engine cell testing. All motors, whether automobile or boat, are Pre-Tested for several hours prior to shipping. The emissions from these Engine Cells are mostly Carbon Monoxide and unburned fuel, with ...


    By Epcon Industrial Systems, LP

  • Recuperative Thermal Oxidizers for Coffee Roasting

    Coffee Roasting Company Epcon has extensive experience in designing and building Recuperative Thermal Oxidizers for the Coffee Roasting Industry. The Problem A leader in the Coffee Industry needed equipment to control odor and eliminate VOC's from Coffee Roasting. The company went out seeking the technical solutions and went to several manufacturers to ...


    By Epcon Industrial Systems, LP

  • Selected Literature from Johnson Matthey`s Environmental Catalysts and Technologies Division

    SSEC Literature: High Temperature SCR Zeolite Catalyst for NOx Control / SCR Catalyst for NOx Control Stationary Lean Burn Engines / SCR Systems for NOx Control Stationary Lean Burn Engines / Gas Turbine Oxidation Catalyst for the control of CO and VOCs / Oxidation Catalysts for the Control of CO, VOC, HC / BanditoTM - Modular Catalytic Converter for the Control of NOx, CO and THC / Band-ItTM - ...

  • Case study: Regenerative thermal oxidizers for coffee roasting

    Epcon has extensive experience in designing and building Regenerative Thermal Oxidizers (RTO's) for the Coffee Roasting Industry. The Problem A leader in the Coffee Industry needed equipment to control odor and eliminate VOC's from Coffee Roasting. The company went out seeking the technical solutions and went to several manufacturers to locate the best possible technology. ...


    By Epcon Industrial Systems, LP

  • Case study - Engine cell exhaust: Catalytic oxidizer

    Overview Endurance testing of outboard motors for boats has typically been done in lakes and sometimes on barges. This testing was time consuming, presented logistic problems and removed the testing from the R & D department and the factory. When a company in Oklahoma decided to build their own endurance test cell area, the Environmental Protection Agency required them to control the ...

  • Case study - How to properly maintain and service your oxidizer

    Your air pollution control system represents a significant investment in not only initial capital but also ongoing maintenance and operation. Routine inspections performed by your staff combined with thorough maintenance plans provided by Anguil Environmental Service Technicians will ensure you get the most from your investment over the entire life of the system. Anguil has almost three decades ...

  • Medical implant manufacturer succeeds with the QUADRANT SRS Silicone Series Thermal OXidizer - Case study

    Medical Implant Manufacturer Succeeds with Customized Air Pollution Control Equipment Many industries utilize silicone as an ingredient in their manufactured product. Silicone enhances the attributes of the product or helps to improve production characteristics. Whatever the reason may be, users of solvent borne silicone's all face very troubling issues when it comes to the selection of the right ...

  • Reaching Euro VI emissions limits

    The requirements of low and lowest detectable exhaust analysis has prompted Eco Physics to launch a broad range of analyzers for NO/NOx detection. Emissions tuning is one of the targets of the EURO VI regulations as well as US EPA 2010, which are: Reduction of Particulate Matter (PM) and reduction of Nitrogen Oxides (NOx). In the past 15 years – since the first European regulation for exhaust ...


    By Eco Physics Inc.

  • A Modelling Approach to the Design Optimization of Catalytic Converters of IC Engines

    ABSTRACT In this paper, a modelling approach to the design optimization of catalytic converters is presented. The first step of the optimization is the model-assisted sizing of catalysts. For ...


    By DCL International Inc.

  • Automotive parts coater exceeds local air quality requirements - Case Study

    Today many companies are faced with unique air pollution control problems arising from their coating operations. Not only are vented emissions required to be controlled, but now a more pressing issue is how to treat fugitive emissions. Fugitive emissions are the VOC and HAP releases that occur at the coating process or in a mixing area. Fugitive emissions are sometimes difficult to capture when ...

  • Petrochemicals Manufacturing Industry - Pollution Prevention Guidelines

    Introduction Pollution Prevention Guidelines to provide technical advice and guidance to staff and consultants involved in pollution-related projects. The guidelines represent state-of-the-art thinking on how to reduce pollution emissions from the production process. In many cases, the guidelines provide numerical targets for reducing pollution, as well as maximum ...


    By The World Bank

  • Identifying Your Ideal Air Pollution Control Technology, Scenario 3

    In our recent blog, "What's the Best Air Pollution Control Technology for My Process?",  we examined the many factors that can impact a facility's choice of air pollution control equipment. When they are ...

  • Air Pollution Control Specs

    As the full effect of the federal Clean Air Act (CAA) Amendments continue to impact today’s industry, many companies will be required to install new or additional air pollution control equipment.  With more than 25 years of proven success in a variety of industries, catalytic and thermal oxidation has become a popular method for controlling volatile organic compound (VOC) and hazardous air ...


    By The CMM Group, LLC

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you