Fine Particles Equipment For Air And Climate Available In South Carolina
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Filters for the filter stage, Ø70 mm. EMFAB filter, TX40 (100 filters), Ø70 mm. Incl. 100 filters for the filter ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
TSP Inlet for ambient air ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
To remove humidity from the sample. 120 cm, 120 + 60 ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Impactor foil grease 10 g including mixing jar 1:20. Max 100 ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Enables heating of the Dekat® PM10 Impactor up to 200 ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Used for charging and calibrating secondary flow for the real-time measurement ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
For fast greasing of the collection substrates. Stencil not included. Hazardous material, needs special ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
For greasing of 15 foils at one time with Collection Substrate ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
The Dekati PM10 Impactor is a three-stage cascade impactor for determining particle gravimetric mass size distribution. The operating principle of the Dekati PM10 impactor is based on inertial size classification and gravimetric or chemical analysis of the collected, size classified particle samples. This impactor has cutpoints of 10, 2.5 and 1 μm making it an ideal choice for PM10, PM2.5 and ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Impactor foil grease 25 g, max 200 ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
The Dekati Gravimetric Impactor (DGI) is a high sample flow rate cascade impactor for low concentration particle measurement applications. The DGI measures gravimetric particle mass size distribution of particles < 2.5 μm in five size fractions. Typical measurement applications of the DGI impactor include engine emission measurements, air quality studies and other low concentration ...
-
PremiumManufactured by Synspec BVbased in NETHERLANDS
Ozone precursors measurement in the ambient air. Synspec GC 955 series 611/811 is a combination of two gas analysers for online continuous monitoring of ozone precursors in the ambient air. GC 955 811 is specifically designed for the measurement of the hydrocarbons from C2 up to C5 and the model 611 for the hydrocarbons from C6 up to C12. With the combination of these two GCs nearly all of the ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Impactor collection plate set, 14pcs. Spare set of impactor collection plates. Incl. 14pcs of DLPI+ impactor collection plates and a storage case. Storage case for impactor collection ...
-
PremiumManufactured by HI-Q Environmental Products Company, Inc.based in USA
HI-Q Environmental Products Company’s High Volume PM-10 Size Selective Inlet samples suspended particulate in the air at a flow rate of 40 CFM through its omnidirectional head. The air is then accelerated through multiple internal nozzles toward a greased collection plate. Due to their larger momentum, particles greater than 10 microns cannot negotiate the air stream turn, thereby colliding ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Temperature controller to operate ELA-460/ELA-460B. Same controller for the Dekati Cyclone heater, Heated sampling line DEED-150X and Dekati Diluter ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
PM10 inlet for ambient air measurements. EN 12341 PM10 inlet downscaled to 10 ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
Aluminium foils, 300 pcs, Ø25 mm, Collection foils for DLPI+ impactor stages. Greased aluminium foils, 100 pcs, Ø25 mm, Pre-greased with ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
The Dekati High Temperature ELPI+ (Electrical Low Pressure Impactor, HT-ELPI+) is a unique version of the Dekati ELPI+ that enables real-time measurement of particle size distribution from 6 nm up to 10 μm with 10 Hz sampling rate. The High Temperature ELPI+ allows direct measurement of up to 180 °C high temperature aerosol samples without the need to cool the sample, which makes the ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
The HT-DLPI+ (High Temperature Dekati Low Pressure Impactor) is a 14-stage cascade impactor that is used to determine airborne particle mass size ...
-
PremiumManufactured by Dekati Ltd.based in FINLAND
For sampling from max 600 °C. 230 V (also available as 2 m version) 110 V. Can be operated with temperature controller ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you