Gas Purification Equipment For Air And Climate Near Europe
-
Manufactured by Detector Oybased in FINLAND
The SDM-3R is a versatile maintenance tool that automates the service of a GX-3R and GX-3R Pro portable gas monitors. This docking station can be used as a stand alone device for charging, calibration and bump testing. If connected to a PC you can also change the parameters of the monitors and archive calibration calibration/bump testing ...
-
Manufactured by Protea Limitedbased in UNITED KINGDOM
For heated gas sampling from up to 4 separate sample points, Protea’s Heated Stream Selection Module (HSSM) is a ready to use 19" rack interface that can be used with Protea’s range of multigas FTIR analysers or any other industrial gas ...
-
Manufactured by Sulzer Ltd.based in SWITZERLAND
Sulzer helicoaxial multiphase pumps enable boosting of the oil/gas/water mixture from producing wells, without separating the gas from the liquids. They are successfully deployed in remote or subsea location, thus making wells and fields economically ...
-
Manufactured by Adfis Products Gmbhbased in GERMANY
If, in addition to the chemical cleaning of H2S, high demands are placed on the physical adsorption capacity at the same time, then good advice is usually rare. Both, doped and impregnated activated carbon can then often exhaust their potential just ...
-
PremiumManufactured by Jacobi Groupbased in SWEDEN
Activated carbons designed for air and gas treatment, covering a diverse set of applications including VOC abatement in air, odour control, solvent recovery, process gas purification, residential and commercial air treatment devices, cigarette filters, and cabin air filters and evaporative loss devices in automobiles. ...
-
PremiumManufactured by Jacobi Groupbased in SWEDEN
In many cases, activated carbon must be applied in adsorption systems designed for the specific service in mind. Properly designed systems will ensure optimal and safe utilization of the carbon, and aid in the removal and exchange of the carbon once it is spent. Jacobi offers a full range of pre-designed, modular systems, which allow for flexibility of operation and reduction of capital costs, ...
-
Manufactured by Rhodius GmbHbased in GERMANY
Droplet separators are designed as the fundamental unit for operating various process and technical facilities. kms offers knitted wire mesh and coalescence elements with highly efficient separation performance. Unwanted contaminants from gas streams are separated until the required concentration of the pure gas is obtained. With the help of computers and our design program “Separate ...
-
Manufactured by SAXON Junkalor GmbHbased in GERMANY
The Infralyt SMART was designed to perform the emissions test on vehicles. The device determines the gas components CO, CO2, HC as normal hexane via infrared absorption and O2 via the electro-chemical principle. With a simplification of “Brettschneider” formula, an air-fuel ratio is calculated, which decides on the stoichiometric quality of the combustion process from the exhaust gas. ...
-
Manufactured by Muntersbased in USA
Munters DPV is a double pocket type vane type separator for service in high velocity and high liquid removal applications. It is part of Munters series of high performance vane type separators (DH5000 and DPV) with elevated K-values. Specially designed drain channels collect the liquid which flows away under the influence of gravity. So-called double pocket vane type separators drain the captured ...
-
Manufactured by Muntersbased in USA
Munters Easy Flow enables to master critical process conditions where there is either a high solid content in the gas thus a high risk of clogging or where there is a very high variance in the flow conditions leading to local malfunctions in the separation. This innovative technology concept increases the service life of coarse and fine separators in gas cleaning devices and equalizes uneven gas ...
-
Manufactured by Muntersbased in USA
The DV Series droplet separators are a vane type separators. The gas flow charged with liquid droplets is directed through separator chambers which are designed for maximum effect on the gas ...
-
Manufactured by Körting Hannover AGbased in GERMANY
Gas entering the droplet separator is set in rotation by a specially formed twist generator which causes droplets to be propelled outwards as a result of the centrifugal action. The separator chamber is shaped as a spiral tube. Droplets caught on the walls converge to form a liquid film which runs downwards towards the discharge point and not upwards in the direction of the gas flow. This special ...
-
Manufactured by Körting Hannover AGbased in GERMANY
The Venturi scrubber is utilised to separate dusts and hazes with particle sizes of less than 3 µm. Amongst other things, dedusting is dependent on: particle diameter and -density, droplet diameter and -quantity, the relative velocity between particles and ...
-
Manufactured by Körting Hannover AGbased in GERMANY
Jet scrubbers are utilised for basic operations such as: Cooling - Scrubbing - Conveying. Exhaust air is accelerated by means of impulse exchange with t he motive-/rinsing liquid. This suction effect facilitates a gas-side pressure gain with which flow resistances can be compensated for. The action of atomising the rinsing liquid into the cylindrical part of the scrubber causes it to be filled ...
-
PremiumManufactured by BUCHIbased in SWITZERLAND
Sepiatec’s new SFC-250 system is a compact benchtop unit designed for preparative separation using supercritical fluid chromatography. Measuring just 72 x 60 x 88 cm (W x D x H) the system offers all advantages of SFC technology such as fast separation, reduced consumption of organic solvents, lower costs, improved environmental compatibility and increased ...
-
PremiumManufactured by BUCHIbased in SWITZERLAND
Sepiatec’s SFC-M5 50 system is a preparative system for separating chiral and achiral samples using supercritical fluid chromatography. The SFC-M5 50 system consists of the main module and the collector module. Both modules form a functional unit that can be configured in a variety of ways with different equipment. The main module can be equipped with up to three high pressure pumps, a CO2 ...
-
PremiumManufactured by BUCHIbased in SWITZERLAND
Sepiatec’s SFC-M5 250 system is a preparative system for separating chiral and achiral samples using supercritical fluid chromatography. The SFC-M5 250 system consists of the main module and the collector module. Both modules form a functional unit that can be configured in a variety of ways with different equipment. The main module can be equipped with up to three high pressure pumps, a ...
-
PremiumManufactured by BUCHIbased in SWITZERLAND
The SFC-660 system, developed by Sepiatec, represents a powerful solution for preparative separations by means of supercritical fluid chromatography (SFC). The unit has been designed for flow rates of up to 660 ml/min at a modifier portion of 40 %. All the advantages of SFC technology are combined: Quick separation, a reduced consumption of organic solvents and thus cost, increased safety and an ...
-
PremiumManufactured by BUCHIbased in SWITZERLAND
The SFC-50 from Sepiatec is a compact and easy-to-use chromatography system for preparative separations on small columns by means of supercritical fluid chromatography (SFC). The system offers the comprehensive benefits of SFC technology, such as faster separations, lower costs due to reduced consumption of organic solvents, as well as being more environmentally friendly at increased ...
-
PremiumManufactured by BUCHIbased in SWITZERLAND
Sepiatec’s SFC-M5 system is a preparative system for separating chiral and achiral samples using supercritical fluid chromatography. The system is available in the product variants M5 50 and M5 250. The SFC-M5 system consists of the main module and the collector module. Both modules form a functional unit that can be configured in a variety of ways with different equipment. The main module ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you