Particulate Applications

36 Results found
Only show results available in Virginia?
OK
  • Category: Air & Climate ×

  • Subcategory: Particulate ×

Stack Testing for Rod Mill Exhaust Stack

by AirSource Technologies, Inc.     based in Shawnee, KANSAS (USA)

STEEL INDUSTRY: Conducted particulate testing and continuous emission monitoring of a rod mill exhaust stack. In addition, testing was performed to determine emissions associated with a slow cooling pen associated with ball mill production.

Natural gas gathering system for inlet gas separation

by Pentair Filtration Solutions, LLC     based in Conroe, TEXAS (USA)

Natural gas gathering systems deliver large volumes of gas via pipleline to the central inlet of the gas processing facility. Removal of solid contaminants and free liquids present in the inlet gas is critical to the downstream process. Iron oxides, iron sulfides, dirt and other deformable particles can flow into the processing system. Effective removal of these contaminants is needed to prevent fouling. Pentair Porous Media technologies will help with a clean, natural gas feed, reducing upsets and associated downtime and increase productivity, lowering capital costs with fewer change-outs.

High performance separation system for fuel gas streams

by Pentair Filtration Solutions, LLC     based in Conroe, TEXAS (USA)

Fuel Gas Streams are frequently contaminated with liquid aerosols. The liquid exists as a stable and persistent “smoke” in the gas stream. The liquid contaminant can enter the gas stream through any one of a variety of events including – phase separation and condensation, compressor lube-oils from compression, chemical addition to pipelines (including corrosion inhibitors), and entrainment from overheads of contact towers.

Sediment and Nutrient Loads

by FTS     based in Victoria, BRITISH COLUMBIA (CANADA)

SedEvent is an event-driven, automatic grab sampling system that provides a simple and practical method of accurately determining suspended sediment and nutrient loads. While suspended sediment concentration (SSC) cannot be directly measured accurately or reliably, turbidity has been shown to be an excellent surrogate for SSC. Turbidity is caused by suspended particulate matter such as clay, silt, algae, organic and inorganic chemicals and acids like fertilizers, and microscopic organisms like harmful bacteria. These contents give water its cloudy or turbid appearance, and turbidity in natural waters is recognized as an important indicator of natural health. Measuring suspended sediment concentrations used to be labor-intensive, costly, inaccurate and impractical. SedEvent not only makes it possible and practical, it makes it simple.

Odour removal units for professional kitchen ventilation

by Dimtech S.A     based in Keratsini, GREECE

Our company has odour removal units for professional kitchen ventilation, for grills and food preparation areas generally. The operation of the unit is based on chemical or electrostatic filters or a combination of both. The kitchen unit KDSA (with chemical filters) series, neutralizes particles, soot, odors, grease and moisture completely. KDSA units for kitchen ventilation are installed in the cooker hood and are connected with the kitchen areas that produce smoke or where there is smoke and odors such as in kitchen funnels or in washing facilities. The air stream in the deodorizer passes through a set of filters where particles, grease, soot and odors are removed.

Dust monitoring of exhaust gases from manufacturing processes

by DynOptic Systems Ltd     based in Brackley, UNITED KINGDOM

DynOptic dust monitors use the innovative Dynamic Detection Principle (DDP) to measure dust and particulate within exhaust gases from various manufacturing processes. DDP, or optical scintillation as it sometimes referred to, measures the dynamic fluctuation in light transmission as dust particles move through a light beam. This dynamic fluctuation derives from temporal distributions of the dust particles which attenuate the light beam. The more dust present in the exhaust, the greater the amplitude of these fluctuations. DDP instruments calculate the dynamic response, or the ratio of light variation to light intensity, which for particular applications, is proportional to dust concentration and when calibrated against standard reference measurements, this can be presented as a reading in mg/m³.

Contaminated Water Filtration

by Omnitec Design, Inc.     based in Mukilteo, WASHINGTON (USA)

Industry standard best practices are designed to ensure that all work done on Asbestos Abatement Projects is done to the highest level of safety and risk management. Containment of the generated waste water fibers and debris is critical to proper compliance and worker safety. If these fibers are not captured and contained, they can be very harmful for the environment, on-site workers and the occupants of neighboring areas. Exactly how you approach your containment and capture solutions will depend on the individual site’s risk assessment report. If you need help identifying solutions to the issues raised in the report, feel free to contact our customer service department and we can review your options together. Water from showers at Asbestos Abatement sites is often contaminated with asbestos fibers from washing protective gear and equipment. This water must be filtered prior to discharge into a drain.

Particulate matter, halogens and aerosols

by Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control     based in Graz, AUSTRIA

Without CTP's innovative upstream systems, regenerative thermal oxidation would not be possible, which would render the waste gas purification cost-intensive and inefficient. Continuous burning off in the RTOs eliminates the deposits which periodically clog the ceramic honeycomb blocks.

Air pollution control solution for the particulate matter

by Macrotek Inc.     based in Markham, ONTARIO (CANADA)

Regulations around the globe are becoming more and more stringent for particulate emissions. Macrotek offers some of the most efficient wet and dry technologies to meet the latest EPA, EU, and MOE standards. Often, particulate collection is combined with acid gas removal. Our most advanced wet-dry system meets and exceeds the most stringent regulations for both hazardous gases and particulate.

PM2.5/PM10 particulate monitoring

by Opsis AB     based in Furulund, SWEDEN

OPSIS provides real-time, flexible monitoring of particulate matter in the ambient air. Particulate matter monitoring with OPSIS, is a cost-effective solution, is ideally suited for use in modern monitoring stations. It can be remote controlled and includes automatic calibration, features that frees time.  The SM200 meets the new regulation for automatic monitoring of PM10 and PM2.5. It also meets the new regulation for particulate matter sampling on filter membranes for further analysis of cadmium, nickel, PAH and other substances.

Applications and Air Pollutants Removed for Mineral Products Industry

by Bionomic Industries Inc.     based in Mahwah, NEW JERSEY (USA)

Removal of acid gases and particulate from cement, brick and other product kilns. Mineral product dryers including coal. Hot mix asphalt plant particulate control. Sulfur dioxide and hydrochloric acid gas removal.

Specialty Cleaners and Lubricants for Electronics Industry

by International Products Corporation     based in Burlington, NEW JERSEY (USA)

Our cleaners are used in the manufacture of semiconductors, flat panel displays, CDs, DVDs, and many other electronic items.  They remove emulsions, particulates, oil, organic and inorganic contaminants from quartz, wafers, glass, silicon, ceramics, and metals.  When rinsed properly our products leave absolutely no residue.  They are also proven in removing soils from filter membranes used in wastewater treatment systems.

Low level measurement of VOCs and Terpenes close to the sea and the Landes Forest

by Chromatotec Group     based in Val de Virvée, FRANCE

It has been established that organic aerosol (OA) makes up for a major fraction of fine particulate matter in all region of the atmosphere. This fraction accounts approximately for half of the total PM2.5 dry mass.1,2 Primary OA is directly emitted in the troposphere from anthropological and natural sources whereas secondary OA (SOA) is formed in-situ in the atmosphere from the oxidation of biogenic or anthropogenic gas-phase precursors and subsequent partitioning of the less volatile products into the particle phase. The current number is that, on a global scale, SOA would represent around 60% of the overall OA.3 However, recent global mass-balance estimations for the removal of volatile organic compounds (VOC) suggest that this number could under-predicts SOA production.4 Recent field measurements in urban locations are also in support of a larger share, indicating that SOA is the dominant fraction of OA, with amounts considerably 20 greater than models predictions.

Industrial and commercial water filtration for heating / cooling systems

by Hydro-Gen Engineering Ltd     based in Widnes, UNITED KINGDOM

Heating or cooling systems, conventional or alternative, involve water. Over time that water picks up particles which in extreme cases can silt up entire heating systems, requiring expensive maintenance, repair or even replacement. A build-up of solids no thicker than a human hair inside pipework can reduce heat transfer by up to 30%, drastically reducing efficiency and increasing energy consumption.

Continuous Gravimetric Feeding for Coal Mining Industry

by Schenck Process Germany     based in Sandnes, NORWAY

Applications in coal mining, the processing of non-ferrous metals, costeaning and preparation in mines require technology and materials capable of withstanding the most extreme conditions. Schenck Process solutions prevail where others give up. Our products are durable, indestructible and extremely reliable under the most difficult conditions.

Whether large lumps or the finest fragment, wet or dry and irrespective of whether using ore, scrap, lime powder or hot sinter up to 1,000 °C – vibratory equipment supplied by Schenck Process can deal with all types of bulk materials. Every year around 10 million tonnes of raw coal are freed of impurities with the help of our coal washing plants – which represents our contribution to environmentally friendly energy production.

Our customised application solutions include both heavy-duty and static weighing technology, conveying, screening, drying & cooling and dewatering. From planning and design through to the construction of the plant sections, reliable controls and connection to data systems.

Restoration

by Omnitec Design, Inc.     based in Mukilteo, WASHINGTON (USA)

Restoring structures after floods and fires is a constantly evolving industry. In addition to keeping up with industry best practices for health and safety of both the contractors and the building residents post restoration, it is also important to be working with modern and reliable restoration equipment. Utilizing Omnitec and OmniAire products will allow you to take advantage of the latest best practice methods with equipment you know will work reliably and safely. Airborne contaminates and dust is a significant consideration for almost any restoration project. Did you know that studies have shown a substantial increase in air particulate matter during the drying process? Not only does dust and contaminates affect your worker’s safety, but also the safety of the post-restoration occupants. Just increasing the air circulation doesn’t remedy the situation and, without adequate filtration, may actually create more problems.

Applications and Air Pollutants Removed in Municipal Water Treatment Plants

by Bionomic Industries Inc.     based in Mahwah, NEW JERSEY (USA)

Applications include: emergency chlorine scrubber systems for cylinder storage area. Removal of powdered carbon particulate emitted from storage silo vents during the loading operation. 

Roadside monitoring

by Ecotech Pty Ltd     based in Knoxfield, AUSTRALIA

Traffic, especially in urban locations, is one of the greatest contributors to air pollution. Traffic produces a variety of different pollutants that include particulates, NO2, NO, CO, hydrocarbons and in some cases SO2. The monitoring of roadside pollution can be challenging as often it is difficult to find suitable locations for large air quality monitoring systems and many sites that are available can be too far away to be representative of roadside air pollution.

Need help finding the right suppliers?

Let the XPRTs do the work for you