Only show results in Virginia? Ok

air emissions monitoring Applications

  • Premium

    Continuous emissions monitoring for mercury monitoring

    Waste incinerators, cement plants and power plants need good and reliable measurements of total gaseous mercury. The measurement of total gaseous mercury is a challenge due to chemical reactions and contamination. The installed systems will often require a lot of maintanence still not giving reliable results.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Monitoring solutions for the continuous emissions monitoring

    Multi-gas Stack Analyzers for Continuous Emissions Monitoring. FTIR and UVDOAS Analyzer Models available for Insitu Probe, Internal or External Cells, or Cross Stack Sample Acquisition.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Opacity monitoring for continuous emissions

    The history of air pollution regulation dates back as far as the 13th century when in 1273, Edward I (Longshanks) of England prohibited the burning of sea coal in London. The smoke produced by its combustion was considered detrimental to human health. By the late 19th and early 20th centuries, regulations were being passed that sought to control air pollution predominantly for smoke and odour control. Traditionally, regulators were concerned with the visual impact of the discharge from a stack or chimney. Therefore, emission limits were expressed in terms of colour or opacity. Modern methods for opacity measurement still use the darkness of the stack gases to measure the amount of smoke or dust emitted within the exhaust gases.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Continuous Emission Monitoring

    By MRU Instruments, Inc. based in Houston, TEXAS (USA).

  • Measurement solution for VOC emissions monitoring

    Protea has used our VOC gas analysers in many projects requiring the monitoring of complex mixes of VOCs. In the chemical and pharmaceutical industry, VOC abatement plants such as scrubbers and carbon-bed systems are typical installations where the use of Protea analysers and our VOC analysis expertise have proved valuable to plant operators. They prove a very powerful and flexible tool in both process gas measurements and VOC emissions monitoring. In the laboratory, Protea can deliver instruments with all the chemometric software and support to enable users to measure hundreds of gases.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Continuous emissions monitoring for brick plants

    Process control and emissions monitoring in a brick plant is a challenge due to the high concentrations of HF. The HF is generated in the process and gas phase HF can reach 50 mg/m3 or more. To use an extractive system in this environment will demand a lot of maintanence.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Emissions Monitoring for Chemical Plants

    The Opsis gas monitoring system is designed for monitoring in stacks and gas ducts in chemical industries, both in order to increase plant efficiency and to monitor emissions. The Opsis systems have been internationally approved by e.g. the German TÜV and the U.S. EPA.

    By Opsis AB based in Furulund, SWEDEN.

  • Fugutive Emissions Measurement

    Emission Measurement – An estimate of the total fugitive emissions from a site can be determined using environmental data, EPA gas dispersion models, and GasFinder2 sensor data.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Premium

    Emissions Monitoring for Airports

    Opsis systems provide high-performance monitoring of the emission activities within an airport. The rapid system allows on-line monitoring of the emissions from each aircraft at take-offs and landings, monitoring of fugitive emissions from stationary sources and differing of the airport sources from the surrounding pollution sources.

    By Opsis AB based in Furulund, SWEDEN.

  • Particulate monitoring for continuous emissions

    With the advent of specific process emission limits being defined, continuous particulate monitoring has become a regulatory requirement for many industries. smoke stack #1Particulate monitoring requires the measurement of the mass concentration of particulate matter in stack emissions to atmosphere. There is no known method of continuously measuring particulate concentration by direct measurement and therefore, all continuous particulate measurement methods are inferential. Each method involves the measurement of a parameter related to particulate concentration and then requires a calibration to be determined to convert the measured value into one of particulate mass concentration.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Premium

    Continuous emissions monitoring for CO2 capture

    The process control of a CO2 capture plant needs good and reliable detection of gas phase NH3 and CO2. Measuring NH3 is a challenge due to the corrosive environment and high concentrations of NH3. Several places in the process needs to be monitored and to transport the sample is difficult. A large dynamic range is needed as the NH3 concentration can vary between 15% volume and a few mg/m3.

    By Opsis AB based in Furulund, SWEDEN.

  • Air monitoring equipments for material emissions and product testing

    A wide variety of products that are used in our indoor environments may emit harmful substances, raising health and safety concerns in homes, offices, public places and vehicles. There is increasing demand to reduce VOC emissions from indoor sources, backed by European legislation. REACH regulation is a European initiative for the Registration, Evaluation, Authorisation and Restriction of Chemical Substances. It was implemented to protect human health and the environment from harmful emissions of chemicals into the air we breathe. The REACH regulation places the responsibility on manufacturers and importers to test their products and provide safety information to the purchaser, end user or consumers.

    By Gradko International Ltd based in Winchester, UNITED KINGDOM.

  • Air Monitoring

    The recent COP 21 meeting reexposed the need for global coordination to monitor Green House Gases (GHG) as well as emissions of ChloroFluoroCarbons (CFC). Networks of sensors have been deployed over the Earth to measure concentration of gases such as methane, carbon monoxide, ethane, carbon dioxide, nitrous oxide, nitrogen oxide and dioxide (NOx)… Such task requires instrument with not only ultra high accuracy but also ultra high precision. Our QCNose Instruments  have been designed for such operations where reliablity combines with performances.

    By Aerovia based in Reims Cedex 2, FRANCE.

  • Premium

    Measurement of hydrogen sulfide & carbon disulfide in air for continous emission monitoring

    The Series 8900 Hydrogen Sulfide and Carbon Disulfide Analyzer provides direct measurement of H2S and CS2 in ambient air. This instrument is utilized for continuous emission monitoring. The Series 8900 H2S and CS2 Analyzer employs a Photoionization detector (PID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is carried to the pre-cut column. Backflush is timed so that only the H2S, CS2, and other similar components are eluted to the analytical column. Contaminants on the pre-cut column are backflushed to vent. H2S and CS2 are separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By AMETEK MOCON - Baseline based in Lyons, COLORADO (USA).

  • Premium

    Ambient air and emissions monitoring of Polycyclic Aromatic Hydrocarbons – airmoC10-C20+

    Polycyclic Aromatic Hydrocarbons (PAHs) are a group of over 100 different chemicals that are known to be formed typically during incomplete combustion of organic matter at high temperature. Their major sources in the atmosphere include industrial processes, vehicle exhausts, waste incinerations, and domestic heating emissions. Due to their carcinogenic/mutagenic effects, 16 PAHs are currently listed as priority air pollutants.

    By Chromatotec Group based in Val de Virvée, FRANCE.

  • Continuous Emissions Monitoring

    Requirements for monitoring emissions to air are governed by EU/UK legislation and are implemented in the form of a permit by the Environment Agency or local authority. The Dr Foedisch muti-component gas analysers continuously extract a gas sample from the exhaust stream via a stack probe into the analyser cabinet. Both hot and cold gas systems are available, please contact us to discuss which system best suits your requirements.

    By CEM Solutions (UK) Ltd. based in Darley Dale, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for engine emissions measurements

    The exhaust gas from combustion engines is a complex mixture of gases and particulate matter. The composition of the gas may change rapidly. Multicomponent analysis of exhaust gases can be performed with a Gasmet™ FTIR Gas Analyzer with a response time (T90) of one second. The winning combination is the result using of a small volume gas sample cell, a powerful sample pump and a fast detector with liquid nitrogen cooling. The analyzer, sampling system and computer can be assembled on a cart for use in a dynamometer laboratory, or the portable version can be used for roadside tests.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Fence-Line Monitoring of Fugitive Emissions

    The Opsis open path monitoring system is an excellent tool for monitoring air quality, fugitive emissions and gas leaks at industrial sites. By arranging monitoring paths strategically at locations outside the borderline of an industrial area, fugitive emissions and gas leaks will effectively be detected. By combining the measured gas data with meteorological parameters information such as where the pollution sources are located and the strength of the emissions can be calculated, using the EnviMan software.

    By Opsis AB based in Furulund, SWEDEN.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you