The process control of a CO2 capture plant needs good and reliable detection of gas phase NH3 and CO2. Measuring NH3 is a challenge due to the corrosive environment and high concentrations of NH3. Several places in the process needs to be monitored and to transport the sample is difficult. A large dynamic range is needed as the NH3 concentration can vary between 15% volume and a few mg/m3.
With over 15 years of experience in the measurement of volatile organic compounds (VOC), Environment SA announces the VOC72M, a new generation analyzer for the measurement of BTEX compounds by gas chromatography with photo-ionization detector (PID). The VOC72M can handle up to 40 compounds and eight configurations for analysis. This compact and fully automated analyzer with wide voltage range specifications (90-240V) provides equivalent performance to the laboratory chromatographs and is particularly suited to...
The Series 8900 BTEX Analyzer with a high-sensitivity PID provides direct low level measurement of Benzene, Toluene, Ethylbenzene, and Xylene`s in ambient air. This instrument is utilized in ambient air networks around metropolitan areas and fence-line monitoring at industrial sites.
SO2 (sulfur dioxide) is measured in a number of applications. SO2 is used as a food grade preservative and must be regulated in accordance with government-set criteria to be safe for consumers. It is also measured in fuel exhaust to control for environmental pollution and in cement plants for process control.
Oxygen (O2) is a colorless odorless gas, essential to all life on Earth but damaging in high concentrations. An O2 analyzer should thus be employed for safety management and air pollution prevention purposes. LasIR MP110 is perfect for continuous emission monitoring of O2. It is based on TDLAS technology and can be calibrated as an O2 analyzer, providing accurate and reliable measurements. It quickly responds to changes in compound concentration, thus providing continuous emission monitoring for the specified gas.
Ambient air quality monitoring is the systematic, long-term assessment of pollutant levels by measuring the concentration and types of certain pollutants in the surrounding, outdoor air. Some of these pollutants (commonly called ‘Criteria Pollutants’) are considered hazardous to human health and their levels are regulated by government agencies around the world, including the US EPA. Teledyne API provides a complete line of ambient air quality monitoring instruments, including those for both gas and...
Motor vehicle emissions are a major source of air pollution in urban areas and impact the lives of billions of people every day around the world. Motor vehicle exhaust contains toxic chemicals that are harmful to people’s health when exposed at certain levels. These toxic fumes cause smog in the atmosphere, which can affect very broad regional air sheds and contribute to the formation of cancer. Teledyne API has several products specifically designed to meet the challenging demands of near-roadside air...
Continuous Emissions Monitoring Systems (CEMS) are used to measure flue gases from stationary sources at a wide variety of regulated industrial facilities, including power plants, petroleum refineries, petrochemical plants, waste incinerators, pulp and paper producers, and many others. The types of air pollution measured from these sources vary widely based on the industry and process, and many are regulated by government agencies around the world.
Many large combustion plants are now required to monitor mass emissions of major pollutants and to do so requires an accurate measurement of stack gas velocity. The VCEM 5100 is certified to EN 15267 part 3 QAL 1 for all industrial processes including waste incineration. It has several key advantages, firstly the sensors optics are not in contact with the hot and dusty environment, the VCEM 5100 can monitor gases at temperatures exceeding 10000C and the analyser requires minimal maintenance. The VCEM 5100 can be...
Ambient air monitoring involves the measurement of `representative` air in urban, industrial and rural areas. These measurements are used to determine the human exposure to pollutants and can be combined with trace/background monitoring.
Urban pollution is a problem that concerns more and more people in charge of public health. In large cities, car emissions are an important source of atmospheric pollution. This problem is growing as the traffic keeps on increasing. BTEX compounds are present in car emissions. It is therefore important to be able to analyze them with short analysis cycle duration and on a continuous and automatic way.
Air is lifeblood. Daily we inhale approximately 15.000 liter. Still, the air contains invisible pollutants, which vary in its composition and concentration depending on the location. Especially the respirable particles with a diameter of less than 2.5 µm (PM 2.5) were considered to be particularly dangerous.
Car tunnels need ventilation in order to keep air pollution below the limits. When the pollution levels reaches a setpoint, the fans must be started and kept running until the pollution levels decreases.
Cooper Environmental's Xact® 640 has the unique ability to generate high time resolution metals measurement in stacks. This unique capability has the potential to qualify as a substitution for the combination of a Hg/ PM CEMs application as well as the potential for a pollution control system feedback loop that could result in the reduction of pollution control consumables. Our systems have been site certified for compliance measurements at hazardous waste incinerator and secondary lead smelter sites.
The OPSIS open-path monitoring system is an excellent tool for monitoring the air quality, fugitive emissions and gas leaks at industrial sites. By arranging monitoring paths strategically at locations outside the borderline of an industrial area, fugitive emissions and gas leaks will effectively be detected. By combining the measured gas data with meteorological parameters information such as where the pollution sources are located and the strength of the emissions can be calculated, using the EnviMan software.
Ambient air pollution is a continuous problematic since many years, and the various organizations in charge of air quality monitoring work constantly on how to improve their structures and gain the most accurate and reliable data possible. Indeed, the changes in mentality and therefore in urbanism development for example, implies an access to the data faster and at multi-location level.
Air quality monitoring reference stations used nowadays measure with an extreme accuracy in located areas, but requires a lot of...
The Series 8900 BTEX Analyzer provides direct measurement of Benzene, Toluene, Ethylbenzene, and Xylenes in ambient air. This instrument is utilized in ambient air networks around metropolitan areas and fence-line monitoring at industrial sites. The Series 8900 BTEX Analyzer employs a photoionization detector (PID) as the sensing element. This detector is specific to volatile organic compounds. The Benzene, Toluene, Ethylbenzene, and Xylene`s in the gas sample are physically separated using proprietary GC columns.
Opsis systems provide high-performance monitoring of the emission activities within an airport. The rapid system allows on-line monitoring of the emissions from each aircraft at take-offs and landings, monitoring of fugitive emissions from stationary sources and differing of the airport sources from the surrounding pollution sources.