ambient air monitor Applications in Africa

  • Premium

    Perimeter Ambient Air Monitoring

    Cerex Multi-Gas Open Path Analyzers are available in both FTIR and UVDOAS technologies to meet specific requirements for perimeter ambient air quality monitoring, leak detection, fugitive emissions monitoring and ambient air quality monitoring. Cerex multi-gas analyzers offer significant advantages over single gas analyzer arrays, electro-chemical sensor arrays and time integrated air sampling hardware

    By Cerex Monitoring Solutions, LLC. Distributor in Tunisie Tunis-Poste Montplaisi, TUNISIA.

  • Premium

    Ambient Stations for Ambient Air Quality Monitoring

    Ambient air monitoring involves the measurement of `representative` air in urban, industrial and rural areas. These measurements are used to determine the human exposure to pollutants and can be combined with trace/background monitoring.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Premium

    Ambient air quality monitoring at airports

    To measure the ambient air quality at airports is a challenge. The monitoring site needs to be representative for background levels and not dependant on changes in local traffic. A large number of gaseous components need to be measured with high accuracy and high availability. The OPSIS DOAS system provides the user with a fast system that gives high availability at low cost. The impact of aircraft take-offs and landings can easily be followed on-line. The OPSIS system can also monitor fugitive emissions from other sources at the airport.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Premium

    Measurement of diacetyl in ambient air to monitor workplace exposure limits.

    The Series 8900 Diacetyl Analyzer provides direct measurement of Diacetyl in ambient air. This instrument is utilized for environmental monitoring and to monitor workplace exposure limits. The Series 8900 Analyzer for Diacetyl employs a photoionization detector (PID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is carried to the pre-cut column. Backflush is timed so that only the Diacetyl and other similar components are eluted to the analytical column. Contaminants on the pre-cut column are backflushed to vent. The Diacetyl is separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By AMETEK MOCON - Baseline Distributor in Thakanat El-Maadi, EGYPT.

  • Premium

    Ambient air quality monitoring solutions for PM2.5/PM10 particulate monitoring

    OPSIS provides real-time, flexible monitoring of particulate matter in the ambient air. Particulate matter monitoring with OPSIS, is a cost-effective solution, is ideally suited for use in modern monitoring stations. It can be remote controlled and includes automatic calibration, features that frees time. The SM200 meets the new regulation for automatic monitoring of PM10 and PM2.5. It also meets the new regulation for particulate matter sampling on filter membranes for further analysis of cadmium, nickel, PAH and other substances.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Premium

    Open path ambient air quality monitoring

    Cerex Multi-Gas Open Path Analyzers are available in both FTIR and UVDOAS technologies to meet specific requirements for perimeter ambient air quality monitoring, leak detection, fugitive emissions monitoring and ambient air quality monitoring.

    By Cerex Monitoring Solutions, LLC. Distributor in Tunisie Tunis-Poste Montplaisi, TUNISIA.

  • Measurement solution for ambient air workplace monitoring

    Protea can supply fixed workplace monitoring systems that can measure single or multi-points about the workplace. Specifically designed analytical systems can ensure detection limits down to ppb levels can be achieved for multiple gases with a single instrument. Controlling software can run automatically, providing instantaneous or time-weighted average readings.

    By Protea Limited Distributor in Modderfontein, SOUTH AFRICA.

  • Premium

    Measurement of formaldehyde in ambient air for monitoring workplace exposure limits

    The Series 8900 Formaldehyde Analyzer provides direct measurement of Formaldehyde in ambient air. This instrument is utilized in industrial plants to monitor workplace exposure limits. The Series 8900 Formaldehyde Analyzer employs a flame ionization detector (FID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is carried to the pre-cut column. Backflush is timed so that only the Formaldehyde and other similar components are eluted to the analytical column. Contaminants on the pre-cut column are backflushed to vent. Formaldehyde is separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By AMETEK MOCON - Baseline Distributor in Thakanat El-Maadi, EGYPT.

  • Premium

    Measurement of acrylonitrile in ambient air for monitoring workplace exposure limits

    The Series 8900 Acrylonitrile Analyzer provides direct measurement of Acrylonitrile in ambient air. This instrument is utilized in industrial plants to monitor workplace exposure limits. The Series 8900 Acrylonitrile Analyzer employs a flame ionization detector (FID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is carried to the pre-cut column. Backflush is timed so that only the Acrylonitrile and other similar components are eluted to the analytical column. Contaminants on the pre-cut column are backflushed to vent. Acrylonitrile is separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By AMETEK MOCON - Baseline Distributor in Thakanat El-Maadi, EGYPT.

  • Premium

    Measurement of methyl bromide in ambient air for monitoring workplace exposure limits in fumigation facilities

    The Series 8900 Methyl Bromide Monitoring System provides an automated, direct measurement of Methyl Bromide in ambient air. This instrument can meet and exceed the requirements for ambient methyl bromide monitoring. It is utilized in fumigation facilities and industrial plants to detect potential worker exposure to methyl bromide, resulting from mechanical failure, human error or product off gassing. Multipoint sampling options allow the analyzer to monitor multiple sample locations for greater coverage.

    By AMETEK MOCON - Baseline Distributor in Thakanat El-Maadi, EGYPT.

  • Premium

    Ambient air quality monitoring solutions for tunnel monitoring

    Car tunnels need ventilation in order to keep air pollution below the limits. When the pollution levels reaches a setpoint, the fans must be started and kept running until the pollution levels decreases.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Premium

    Ambient air quality monitoring solutions for fence-line monitoring

    The OPSIS open-path monitoring system is an excellent tool for monitoring the air quality, fugitive emissions and gas leaks at industrial sites. By arranging monitoring paths strategically at locations outside the borderline of an industrial area, fugitive emissions and gas leaks will effectively be detected. By combining the measured gas data with meteorological parameters information such as where the pollution sources are located and the strength of the emissions can be calculated, using the EnviMan software.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Measurement solution for accurate continuous formaldehyde measurement formaldehyde in emissions and ambient air applications

    Formaldehyde (HCHO) is the simplest aldehyde species and is present, or generated by, many sources (both natural and industrial). It is classed as a substance that is toxic and harmful to human health.

    By Protea Limited Distributor in Modderfontein, SOUTH AFRICA.

  • Premium

    BTEX in Ambient Air Application using a High-Sensitivity PID

    The Series 8900 BTEX Analyzer with a high-sensitivity PID provides direct low level measurement of Benzene, Toluene, Ethylbenzene, and Xylene`s in ambient air. This instrument is utilized in ambient air networks around metropolitan areas and fence-line monitoring at industrial sites.

    By AMETEK MOCON - Baseline Distributor in Thakanat El-Maadi, EGYPT.

  • Premium

    Ambient air quality monitoring solutions for street-level monitoring

    To measure the air quality in a city is a challenge. A large number of gaseous components need to be measured with high accuracy. The monitoring site needs to be representative for the city and the system has to be easy to maintain and calibrate. The OPSIS open-path monitoring systems provide a flexible solution, giving the average concentration for an area. A single OPSIS system can measure all relevant gaseous components set by the authorities, such as NO, NO2, SO2, O3, BTX, NH3.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Premium

    Measurement of naphthalene in ambient air to monitor workplace exposure limits & at remediation & Superfund sites

    The Series 8900 Naphthalene Analyzer provides direct measurement of Naphthalene in ambient air. This instrument is utilized in industrial plants to monitor workplace exposure limits and at remediation and Superfund sites. The Series 8900 Naphthalene Analyzer employs a photoionization detector (PID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is carried to the pre-cut column. Backflush is timed so that only the Naphthalene and other similar components are eluted to the analytical column. Contaminants on the pre-cut column are backflushed to vent. Naphthalene is separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By AMETEK MOCON - Baseline Distributor in Thakanat El-Maadi, EGYPT.

  • Premium

    Ambient air quality monitoring solutions for remote sensing of ship emissions

    New regulation forces ships to lower the emissions of SO2. Ships travelling in SECA areas has to either run on low sulphur fuel, or install SO2 scrubbers. To measure the SO2 emissions from a ship is not an easy task. OPSIS provides the Port Authorities with a unique measurement principle where the emissions from the ship is measured remotely. Light is passing the emissions and by analyzing the light, concentrations of SO2 can be measured.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Premium

    Urban air quality monitoring

    To measure air quality in the ambient air is a challenge. The monitoring site needs to be representative and not dependant on changes in local traffic. A large number of gaseous components need to be measured with high accuracy and high availability.

    By Opsis AB Distributor in Cheraga, ALGERIA.

  • Dust monitoring and Sand Storm Monitoring

    The frequency and intensity of dust and sand storms in many parts of the world are steadily increasing due to droughts and climate change. The severity of such storms is anticipated to increase over the coming years. These dust storms may last hours or days and cause huge damage and imposed a heavy toll on society with its physical effects, such as visibility reduction, heavy winds, red sky, hailstone and severe lightning. Such Dust storms, have a negative impact on human health, and industrial products and activities. They reduce visibility, layer on skin and cloths, infiltrate buildings and find their way into food and drinking water leaving a permanent sandy feeling in your mouth. Traditional dust monitoring instruments whether they be purely filter based gravimetric samplers or continuous monitors utilising Tapered Element Oscillating Microbalance (TEOM) or Beta Attenuation (BAM) simply are unable to cope with the high dust loads created by these storms. The filters on these instruments are quickly clogged and no further measurements are possible until a service technician visits to replace filters and filter tapes. In dust storm events this is impossible. Therefore, over the past few years a need for alternate technology which are non filter based, can cope with extremely high dust loads, require minimal maintenance and can operate off solar power has been employed in regions such as the Gobi Desert of China for the continuous monitoring of dust storm events. These instruments have demonstrated that an instrument can measure dust storm events with maintenance performed only once every 12 months. That it is possible to communicate remotely and that these systems can not only provide an early warning for dust events but have the accuracy and sensitivity to be an extremely useful tool in gauging hourly changes of visibility. Infact such instruments have been utilised by a number of EPAs around the world, including all Australian EPAs for the purpose of measuring ambient visibility as well as providing an accurate indication of rising dust events.

    By Ecotech Pty Ltd Distributor in SOUTH AFRICA.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you