ambient monitoring Applications | Environmental XPRT

Premium

Monitoring of mercury in ambient air

Mercury, being widespread in environment, has toxic effect on a human organism even at a low concentration. Therefore, quantitativ e determination of mercury in vari ous environments is one of the most important environmental monitoring problems. The use of a mercury analyzer RA-915M/RA-915+/RA- 915Light with Zeeman background correction provides di rect real-time continuous determination of mercury in air from 0.5 ng/m 3 within the overall possible range of me rcury concentration in ambient air.

By Lumex Instruments Group based in Mission, BRITISH COLUMBIA (CANADA).

Premium

Ambient Stations for Ambient Air Quality Monitoring

Ambient air monitoring involves the measurement of `representative` air in urban, industrial and rural areas. These measurements are used to determine the human exposure to pollutants and can be combined with trace/background monitoring.

By Opsis AB based in Furulund, SWEDEN.

Premium

Ambient air quality monitoring solutions for tunnel monitoring

Car tunnels need ventilation in order to keep air pollution below the limits. When the pollution levels reaches a setpoint, the fans must be started and kept running until the pollution levels decreases.

By Opsis AB based in Furulund, SWEDEN.

Premium

Ambient air quality monitoring solutions for fence-line monitoring

The OPSIS open-path monitoring system is an excellent tool for monitoring the air quality, fugitive emissions and gas leaks at industrial sites. By arranging monitoring paths strategically at locations outside the borderline of an industrial area, fugitive emissions and gas leaks will effectively be detected. By combining the measured gas data with meteorological parameters information such as where the pollution sources are located and the strength of the emissions can be calculated, using the EnviMan software.

By Opsis AB based in Furulund, SWEDEN.

Premium

Perimeter Ambient Air Monitoring

Cerex Multi-Gas Open Path Analyzers are available in both FTIR and UVDOAS technologies to meet specific requirements for perimeter ambient air quality monitoring, leak detection, fugitive emissions monitoring and ambient air quality monitoring. Cerex multi-gas analyzers offer significant advantages over single gas analyzer arrays, electro-chemical sensor arrays and time integrated air sampling hardware

By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

Premium

Ambient air quality monitoring solutions for street-level monitoring

To measure the air quality in a city is a challenge. A large number of gaseous components need to be measured with high accuracy. The monitoring site needs to be representative for the city and the system has to be easy to maintain and calibrate. The OPSIS open-path monitoring systems provide a flexible solution, giving the average concentration for an area. A single OPSIS system can measure all relevant gaseous components set by the authorities, such as NO, NO2, SO2, O3, BTX, NH3.

By Opsis AB based in Furulund, SWEDEN.

Measurement solution for ambient air workplace monitoring

Protea can supply fixed workplace monitoring systems that can measure single or multi-points about the workplace. Specifically designed analytical systems can ensure detection limits down to ppb levels can be achieved for multiple gases with a single instrument. Controlling software can run automatically, providing instantaneous or time-weighted average readings.

By Protea Limited based in Middlewich, UNITED KINGDOM.

Environmental monitoring solutions for the ambient air quality monitoring sector

By mlu-recordum Environmental Monitoring Solutions GmbH based in Wiener Neudorf, AUSTRIA.

Premium

Air quality and industrial gas monitoring systems for Ambient air monitoring

Ambient air quality monitoring is the systematic, long-term assessment of pollutant levels by measuring the concentration and types of certain pollutants in the surrounding, outdoor air. Some of these pollutants (commonly called ‘Criteria Pollutants’) are considered hazardous to human health and their levels are regulated by government agencies around the world, including the US EPA. Teledyne API provides a complete line of ambient air quality monitoring instruments, including those for both gas and...

By Teledyne API based in San Diego, CALIFORNIA (USA).

Premium

Process analyzers & instruments for exposure level ambient air monitoring

By Ametek Process Instruments - THERMOX based in Pittsburgh, PENNSYLVANIA (USA).

Premium

Open path ambient air quality monitoring

Cerex Multi-Gas Open Path Analyzers are available in both FTIR and UVDOAS technologies to meet specific requirements for perimeter ambient air quality monitoring, leak detection, fugitive emissions monitoring and ambient air quality monitoring.

By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

Premium

Ambient air monitoring by FID detection – airmoVOC BTEX

Urban pollution is a problem that concerns more and more people in charge of public health. In large cities, car emissions are an important source of atmospheric pollution. This problem is growing as the traffic keeps on increasing. BTEX compounds are present in car emissions. It is therefore important to be able to analyze them with short analysis cycle duration and on a continuous and automatic way.

By Chromatotec Group based in Val de Virvée, FRANCE.

Premium

Ambient Continuous Metals Monitoring/ Fence Line Monitoring/ Source Identification

The Xact® 625i combined with ADAPT software creates the industry's most powerful tool for high time resolution detection of airborne metals. The Xact® 625i measures trace metals at very low detection limits at time resolutions down to 15 minutes. The ADAPT package captures corresponding wind speed and wind direction data, then seamlessly integrates the measurements into wind regression analyses available at the touch of a button. This creates the most single most powerful fence line/ source identification...

By Cooper Environmental Services based in Beaverton, OREGON (USA).

Premium

Ambient air quality monitoring solutions for PM2.5/PM10 particulate monitoring

OPSIS provides real-time, flexible monitoring of particulate matter in the ambient air. Particulate matter monitoring with OPSIS, is a cost-effective solution, is ideally suited for use in modern monitoring stations. It can be remote controlled and includes automatic calibration, features that frees time. The SM200 meets the new regulation for automatic monitoring of PM10 and PM2.5. It also meets the new regulation for particulate matter sampling on filter membranes for further analysis of cadmium, nickel, PAH...

By Opsis AB based in Furulund, SWEDEN.

Premium

Measurement of formaldehyde in ambient air for monitoring workplace exposure limits

The Series 8900 Formaldehyde Analyzer provides direct measurement of Formaldehyde in ambient air. This instrument is utilized in industrial plants to monitor workplace exposure limits. The Series 8900 Formaldehyde Analyzer employs a flame ionization detector (FID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is...

By AMETEK MOCON - Baseline based in Lyons, COLORADO (USA).

Premium

Measurement of acrylonitrile in ambient air for monitoring workplace exposure limits

The Series 8900 Acrylonitrile Analyzer provides direct measurement of Acrylonitrile in ambient air. This instrument is utilized in industrial plants to monitor workplace exposure limits. The Series 8900 Acrylonitrile Analyzer employs a flame ionization detector (FID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is...

By AMETEK MOCON - Baseline based in Lyons, COLORADO (USA).

Ambient Monitor Gas Calibration with Ozone Generators

Environics® Ambient Monitor Calibrator with Ozone Generators facilitate dynamic calibration of ambient air analyzers. These instruments automatically perform zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, O3, hydrocarbons and other gases of interest. All ozone generators are factory calibrated using a NIST traceable ozone standard. The Series 6100, Series 6103 and Series 9100 all meet or exceed U.S. Environmental Protection Agency requirements.

By Environics, Inc. based in Tolland, CONNECTICUT (USA).

Premium

Ambient air quality monitoring at airports

To measure the ambient air quality at airports is a challenge. The monitoring site needs to be representative for background levels and not dependant on changes in local traffic. A large number of gaseous components need to be measured with high accuracy and high availability. The OPSIS DOAS system provides the user with a fast system that gives high availability at low cost. The impact of aircraft take-offs and landings can easily be followed on-line. The OPSIS system can also monitor fugitive emissions from...

By Opsis AB based in Furulund, SWEDEN.

Premium

Ambient air and emissions monitoring of Polycyclic Aromatic Hydrocarbons – airmoC10-C20+

Polycyclic Aromatic Hydrocarbons (PAHs) are a group of over 100 different chemicals that are known to be formed typically during incomplete combustion of organic matter at high temperature. Their major sources in the atmosphere include industrial processes, vehicle exhausts, waste incinerations, and domestic heating emissions. Due to their carcinogenic/mutagenic effects, 16 PAHs are currently listed as priority air pollutants.

By Chromatotec Group based in Val de Virvée, FRANCE.

Premium

Measurement of diacetyl in ambient air to monitor workplace exposure limits.

The Series 8900 Diacetyl Analyzer provides direct measurement of Diacetyl in ambient air. This instrument is utilized for environmental monitoring and to monitor workplace exposure limits. The Series 8900 Analyzer for Diacetyl employs a photoionization detector (PID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is...

By AMETEK MOCON - Baseline based in Lyons, COLORADO (USA).

Subscribe to our eBulletins

Add Supplier Profile