Only show results available in Virginia? Ok

calibration system Applications

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Weather Monitoring Systems for calibration and test fixtures

    Climatronics remains committed to the needs of our customers and the requirements of the regulatory compliance markets that we serve. We offer a full compliment of test equipment to support field audits and calibration of our sensors and systems. Additionally we maintain a calibrated wind tunnel at our headquarters and offer documented NIST-traceable calibrations on most of our sensors. We have a fully developed and approved quality assurance program which insures the validity and integrity of our calibration procedures.

    By Climatronics Corporation based in Bohemia, NEW YORK (USA).

  • Production of high-accuracy ethanol calibration gas

    Fast and highly accurate analyzer system was needed for ethanol calibration gas standards. Precisive`s OXS-3100-HC configured for ethanol gas was selected due to its sub-ppm repeatability and high stability.

    By MKS Instruments, Inc. based in Andover, MASSACHUSETTS (USA).

  • Premium

    Gas analysis & monitoring system for gas generation

    The gas generators for calibration based on the use of “Method of Permeation Tubes.”. The permeation tubes are sealed capsules containing a small amount of the component that is in contact with a permeable membrane stable. The permeation through the membrane produces a vapor of the compound of the component of small quantity, very stable as a stream in time. This permeate stream by mixing with a dilution gas controlled and precise (for example nitrogen) creates a mixture in track at the desired concentration. The flow of the permeate is measured metrically through severe weight loss of the tube thus ensuring a standard high precision.

    By ETG Risorse e Tecnologia S.r.l. based in Montiglio, ITALY.

  • Water quality monitoring systems for feedwater, storm & condensate industry

    The most important parameters in Water/Steam Cycles such as Cation conductivity, dissolved oxygen and pH are available as pre-assembled and factory tested units. Dedicated analyzers for sodium, silica, phosphate and hydrazine are also factory tested and calibrated for immediate operation.

    By SWAN Analytische Instrumente AG based in Hinwil, SWITZERLAND.

  • Capabilities of the Adsorbent Tube Injector System (ATIS™)

    The Adsorbent Tube Injector System (ATIS) was developed at Supelco® by R&D Scientists, as a tool to assist in our comprehensive adsorbent research for thermal desorption tubes. The ATIS provides an efficient means of transferring calibration standards in either the gas or liquid phase onto the adsorbent packed tubes. The ATIS employs the technique of flash vaporization to vaporize the sample in a continuous flow of inert gas; the inert gas carries the sample to the tube. The sample pathway of the ATIS is constructed of glass and stainless steel. The calibration standard is injected by a syringe through a replaceable septum in the center of the injection glassware, which is heated. After enough time has elapsed, typically less than five minutes, the tube is removed from the ATIS and analyzed using the appropriate analytical technique for that adsorbent tube.

    By MilliporeSigma based in Bellefonte, PENNSYLVANIA (USA).

  • Premium

    Monitoring solutions for the dust monitors areas

    For large combustion plants and power plants we offer the DCEM 2100 particulate monitor. This monitor is certified to EN 15267 part 3 QAL 1 for all industrial processes including waste incineration. It offers outputs in Transmission, Opacity and mg/m3 (when calibrated against a Standard Reference Method). The DCEM 2100 offers real-time zero and span calibration and an efficient air purge system to prevent optical contamination.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Premium

    Continuous emissions monitoring for power plants

    OPSIS offers fully automated system solutions for continuous monitoring in power plants. The monitoring systems have been tested and approved by the German TÜV and the U.S. EPA among others, for the best performance and longest calibration interval.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Ambient air quality monitoring solutions for street-level monitoring

    To measure the air quality in a city is a challenge. A large number of gaseous components need to be measured with high accuracy. The monitoring site needs to be representative for the city and the system has to be easy to maintain and calibrate. The OPSIS open-path monitoring systems provide a flexible solution, giving the average concentration for an area. A single OPSIS system can measure all relevant gaseous components set by the authorities, such as NO, NO2, SO2, O3, BTX, NH3.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Scrap Metal Recycling

    Recognized as an industry leader in shredder recycling, we operate 50 recycling facilities for metal, green waste, plastic, food waste, rubber, tires, RDF waste. Harden’s facilities are designed with safety and efficiency in mind for both employees and customers. Our equipment is maintained and updated regularly and our scales are calibrated quarterly. The properties of metals provide unique benefits and advantages for their recycling. Unlike other recycled materials, such as paper and plastic, metals can be repeatedly recycled without degradation of their properties. Metals from secondary sources are just as good as metals from the primary sources. The scrap metal recycling lines are extremely heavy duty systems designed for processing scrap steel, electronic waste, aluminum castings and profiles, ect. We offer both medium and high capacity plants which benefit from low maintenance & operational costs, and lower capital investment when compared with the traditional systems.

    By Harden Industries Ltd. based in Zhongshan, CHINA.

  • Premium

    HCl Monitoring in Air

    Hydrogen chloride (HCl) is a colorless, sometimes slightly yellow, gas. It is an undesired environmental component that may be damaging to workers and the surroundings. Exposure limits have thus been established by industries to make sure that the workers operate in a safe environment. HCl monitoring is especially required for incinerators, coal-fired power plants, aluminum recycling and cement plants. Unisearch offers a reliable and easy-to-use HCl analyzer – the TDLAS-based LasIR system. Studies have shown that TDLAS equipment provides data that is more accurate than conventional gas monitoring equipment. When calibrated for HCl monitoring, TDLAS is able to detect this gas among other gases present in the area and provide continuous updates with regards to the changes in its concentration.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Paper & Pulp Industry Emissions Monitoring

    The Procal 2000 emissions analyser is ideally suited to the harsh environments associated with Paper & Pulp Plants.  The in situ, multi-component Continuous Emission Monitoring (CEM) system has an integrated auto-zero and calibration facility, thereby removing the need for intervention by maintenance staff under normal conditions.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Premium

    Measurement of oil in wax for oil & gas industry

    The measurement of oil in wax is important within the oil refining industry because wax derived from petroleum sources is an important by-product of the oil refining process. These waxes are widely used in the manufacture of many materials and products as they have the ability to confer specific mechanical and physical properties such as flexibility, hardness and friction. A wide variety of waxes is manufactured with specific characteristics. One of the most critical factors controlling wax properties is the oil content. This means routine measurement of the content of oil in wax is essential for consistent control of the production process. Our benchtop NMR analyser MQC systems provides a fast, simple and accurate method of measuring oil in wax. The MQC may be calibrated to provide results equivalent to ASTM D721-06 and IP 158.

    By Oxford Instruments plc based in Abingdon, UNITED KINGDOM.

  • Gas Detection

    Gas Detection is our core business, whether portable, colormetric, fixed systems or Hazmat. We do more than get you the equipment you need--we also help you select it, calibrate it, service it and maintain it. Our technicians, our sales reps and top management can speak with authority on the capabilities of our equipment and match it to your specific application. And we are the champions of the one-of-a-kind solution, because we have the know-how and the right tools.

    By Argus-Hazco based in Chesterfield, MICHIGAN (USA).

  • OneRainware™ - Radar rainfall for real-time and analytical applications.

    Accurate estimation of the spatial distribution of rainfall is critical to successfully model hydrologic processes. OneRain has worked with engineering firms and those with responsibilities in Stormwater and Wastewater Management across the U.S. to provide radar rainfall data to help characterize storm events or flow problems in collection systems and as a basis for both real-time and design-oriented modeling. OneRainware products and services offer: *Real-time gauge-adjusted radar rainfall (GARR) data *Real-time area-average rainfall *Real-time forecast rainfall *End-of-month archive quality gauge-adjusted radar rainfall data *Historical and post-event analysis using archived rainfall estimates *Web-delivered calibrated radar-rainfall data *StormProperties™ Analysis. GARR data are used in flood warning, runoff modeling, basin modeling, I/I studies, litigation, real-time control, design storms, and National Pollutant Discharge Elimination System (NPDES) compliance activities.

    By OneRain Incorporated based in Longmont, COLORADO (USA).

  • Fugitive emissions monitoring on industrial sites

    The real-time monitoring of odorous gases or more classical pollutants emitted by industrial sites (wastewater treatment plants, refineries, landfills, etc.) appears nowadays as a requirement, in order to optimize the site process and operations, or communicate towards the neighborhoods and local public bodies. While emissions can be measured directly at the source (in the stack, exhaust, etc.), ambient air measurement all around the sites provides a better accuracy and anticipate pollution episodes. This is why Cairpol developed around its Cairsens sensors a concept of smart and autonomous stations: Cairnet. Without any maintenance nor calibration, Cairnet is a completely autonomous system energy-wised, with user friendly and efficient interface, accessible from any internet-connected device.

    By Cairpol based in La Roche Blanche, FRANCE.

  • Computerized instrumentation for the medical gas flow and scientific research

    Environics gas mixing, blending and dilution systems provide for precise mixing of gases for a wide variety of clinical applications. Our systems can produce gas concentrations from percent to ppb levels for single or multi-point calibration. The high accuracy of our mixers make them the units of choice for a wide variety of laboratory and research applications. For example, Environics Biological Atmosphere Incubation Mixers provide stable and accurate gas mixes for any laboratory or clinical need. You can generate the specific reduced oxygen environments needed for anerobes as well as the enriched oxygen environments needed in a variety of cellular, viral and high density culture applications. Systems can also be used to create a specific and stable gaseous environment in a clean room. In all cases, the Environics Atmosphere Mixers allow you to use less expensive single-gas cylinders or bulk tanks in place of a high number of expensive blended cylinders.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you