Only show results available in Virginia? Ok

cems system Applications

  • Biomass Plant Emissions Monitoring (CEMS)

    Procal´s analysers are used extensively in reporting and control applications in modern Biomass plants. The flexible and reliable instruments form the heart of the systems, enabling CO, NO2, NO, SO2, H2O, CO2, O2, dust and velocity to be measured.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Continuous Metals Stack Monitor (CEMs)

    Cooper Environmental's Xact® 640 has the unique ability to generate high time resolution metals measurement in stacks. This unique capability has the potential to qualify as a substitution for the combination of a Hg/ PM CEMs application as well as the potential for a pollution control system feedback loop that could result in the reduction of pollution control consumables. Our systems have been site certified for compliance measurements at hazardous waste incinerator and secondary lead smelter sites.

    By Cooper Environmental based in Beaverton, OREGON (USA).

  • Filtration for Flue Gas Analysis and CEMS

    Three Steps of CEMS: 1st Step: Gas Sampling 2nd Step: Gas conditioning and treatment 3rd Step: Measurement/Calibration In first step, the function is to get sample gas and forward to 2nd step for treatment. During this step, it cannot block the probes and cannot result condensation of moisture. So a filter online back flushing should be equipped in this part. The filters to be used: 1, Filter is used to ensure the stability of system and reduce the maintenance 2, Filtration Grade: usually 2 or 3 micron 3, Temp. is around 0-180 deg C 4, Back flushing gas is heated, impulse flushing 5, Filter Material: Titanium Sintered, SS316L Sintered, PTFE sintered, Ceramic Membrane and so on 2nd Step Gas Treatment: #11;The coarse filters and the liquid particle filters The coarse and fine cartridge can filter the small particles in the gas and acid aerosol things to better protect the instruments. The micron can be 0.1micron, filtration rate can be up to 99.99%, two layers can be 99.9999%

    By Shanghai CMI Environmental Technology Co.,Ltd. based in Shanghai , CHINA.

  • Premium

    Gas monitoring instruments and systems for process NOx measurement

    Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement system, and the Gasmet™ FCX Gas Analyzers, both of which utilize the FTIR measurement technique for simultaneous multicomponent analysis of the sample gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Gas monitoring and dust monitoring

    EM-5 series Continuous Emission Monitoring System (CEMS) Counting tail gas emission and realtime concentration NOX SO2 O2 Temperature pressure flow dust

    By HANGZHOU ZETIAN TECHNOLOGY CO., LTD based in Hangzhou, CHINA.

  • Paper & Pulp Industry Emissions Monitoring

    The Procal 2000 emissions analyser is ideally suited to the harsh environments associated with Paper & Pulp Plants.  The in situ, multi-component Continuous Emission Monitoring (CEM) system has an integrated auto-zero and calibration facility, thereby removing the need for intervention by maintenance staff under normal conditions.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Power Plant & Power Station Emissions Monitoring

    For more than 25 years, coal and biomass fired plants have formed the largest installed user base for Procal CEM systems. Throughout this period, there has been increasing environmental scrutiny and process upgrades, including the near-ubiquitous use of after-treatment systems such as sophisticated FGD and SCR.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you