Only show results available in Virginia? Ok

chemical detection product Applications

  • Gas detection analyzers for chemical & pharmaceutical processes

    Chemical and pharmaceutical facilities use a variety of hazardous gases and solvents in their production processes. Whenever these substances are transported, processed or stored, the potential risks are high for hazardous conditions. These substances must be continuously monitored to protect personnel and facilities from accidental releases or leakage. Our various lines of hazardous gas monitoring systems benefit the chemical and pharmaceutical industry in the following applications.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Microbial testing for chemical products industry

    On-the-spot measurement for microbial risk management! Microbial growth in industrial chemicals can present a major problem.· If left unchecked, microbial contamination in raw materials and intermediate products can compromise manufacturing process performance and equipment integrity.· These same sources can also impact final product quality, which if not properly maintained can spoil products while sitting on the shelf.· The best solution is early, accurate detection and proactive treatment.

    By LuminUltra Technologies Ltd. based in Fredericton, NEW BRUNSWICK (CANADA).

  • Premium

    Continuous emissions monitoring for sulphuric acid production plants

    The process control of a sulphuric acid plant needs good and reliable detection of gas phase sulphur dioxide (SO2). To measure SO2 is a challenge due to the corrosive environment and high concentration of SO2. Several places in the process needs to be monitored and to transport the sample gas is difficult. A large dynamic range is needed as the SO2 concentration can vary between 15% volume and a few mg/m3. Most systems installed need a lot of maintenance, sometimes as often as every day.

    By Opsis AB based in Furulund, SWEDEN.

  • VOCs Fugitive emissions detection

    An oil refinery or petroleum refinery is an industrial process plant where crude oil is processed and refined into more useful petroleum products, such as naphtha, gasoline, diesel fuel, asphalt base, heating oil, kerosene, etc,. Oil refineries are typically large, sprawling industrial complexes with extensive piping running throughout, carrying streams of fluids between large chemical processing units. The refining process releases a number of different chemicals into the atmosphere mostly Hydrocarbons which cause severe health and safety hazards. Opgal`s EyeCGas Thermal Imager can detect the leaking gases from a distance and help reducing the threats

    By Opgal Optronic Industries Ltd. based in Karmiel, ISRAEL.

  • VOCs gas leak detection

    An oil refinery or petroleum refinery is an industrial process plant where crude oil is processed and refined into more useful petroleum products, such as naphtha, gasoline, diesel fuel, asphalt base, heating oil, kerosene, etc,. Oil refineries are typically large, sprawling industrial complexes with extensive piping running throughout, carrying streams of fluids between large chemical processing units. The refining process releases a number of different chemicals into the atmosphere mostly Hydrocarbons which cause severe health and safety hazards. Opgal`s EyeCGas Thermal Imager can detect the leaking gases from a distance and help reducing the threat

    By Opgal Optronic Industries Ltd. based in Karmiel, ISRAEL.

  • Gas analysis & monitoring systems for leak searching

    Many chemical compounds and gas are invisible to the naked eye. But there are many companies that make intensive use both during and after the production process. The manner and frequency with which companies are required to monitor, document, report and rectify any escape of volatile gaseous compounds are established by regulations extremely rigid. The technology most widely used is the “Imaging Camera” or “sniffer technology.” “When we look for gas leaks, check all systems in places that may or may not have been previously identified. These controls are carried out regularly and are very important after a shutdown.

    By ETG Risorse e Tecnologia S.r.l. based in Montiglio, ITALY.

  • Premium

    Chemiluminescense based analyzer for semiconductor applications

    NOx detection is an innovative approach in CMP (Chemical Mechanical Polishing) process control. CMP smoothens the wafer surface with a combined chemical and mechanical polishing procedure. During production, wafers are coated by a thin layer. To avoid damage to the wafer surface, for instance by stress cracks, the NOx emitted as soon as the wafer is plane and blank must be measured. Therefore, a high-resolution NOx-detector, capable of determining exactly when the polishing process must be stopped, is essential. This approach is used successfully in manufacturing and development lines worldwide, since 1996.

    By ECO PHYSICS AG based in Duernten, SWITZERLAND.

  • Chromatography systems for environmental monitoring

    With the growth of contamination generated from agricultural and industrial production, it causes a threat to the enviroment including drinking water, atmosphere and soil. The chemists have always seeked out the effective analytical methods to detect and identify chemical contaminants. Dikma provides innovative products and application solutions according to government regulations and industry standards, for air and water quality monitoring, gas detection.

    By Dikma Technologies Inc. based in Lake Forest, CALIFORNIA (USA).

  • NOx analyzers for Semiconductor industry

    NOx detection is an innovative approach in CMP (Chemical Mechanical Polishing) process control. CMP smoothens the wafer surface with a combined chemical and mechanical polishing procedure. During production, wafers are coated by a thin layer. To avoid damage to the wafer surface, for instance by stress cracks, the NOx emitted as soon as the wafer is plane and blank must be measured. Therefore, a high-resolution NOx-detector, capable of determining exactly when the polishing process must be stopped, is essential. This approach is used successfully in manufacturing and development lines worldwide, since 1996.

    By Eco Physics Inc. based in Ann Arbor, MICHIGAN (USA).

  • Bag Filter Plants

    Triboelectric dust probes installed in the clean gas duct after bag filters, cartridge filters or centrifugal separators (cyclones) are used to detect faulty, damaged or leaking filters. This early detection of failures minimises product loss, improves environmental conditions and problematic dust emissions. Benefits include low initial outlay, no consumables and low maintenance requirements. There are more than 10,000 Dr. Foedisch filter monitor devices installed worldwide in the food processing, cement, foundries, quarries, recycling and chemical industries.

    By CEM Solutions (UK) Ltd. based in Darley Dale, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you