Only show results in Virginia? Ok

climate monitoring Applications

  • Premium

    Benzene Monitoring

    Cerex Monitoring Solutions manufactures UVDOAS analyzers for a variety of Benzene monitoring applications. As benzene specific single gas or multi-gas analyzers, our instruments are available with application specific detection ranges and fully configurable alarm functionality.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Air quality monitoring

    To estimate the effects of aerosols on health and climate, it is essential to know their chemical composition. Sampling is done using two different types of aerosol collector. The first type are filter collectors that are based on the deposition of suspended particles on surfaces; the second type are powerful aerosol collectors.

    By Metrohm AG based in Herisau, SWITZERLAND.

  • Meteorological Monitoring

    FTS designs complete, turn-key systems for a variety of environmental monitoring applications. Our systems are based upon the Axiom datalogger—a key technology that deliver rugged reliability in any environment, simplicity of operation, low maintenance costs, and extremely accurate data.

    By FTS based in Victoria, BRITISH COLUMBIA (CANADA).

  • Premium

    Monitoring of leaks in heat exchangers

    Optical instruments called fluorometers can very easily detect and measure dissolved petroleum hydrocarbons in water, and at very low concentrations. As shown in the study below, TD-4100 series monitors are able to measure xylene continuously over four consecutive weeks with a direct correlation coefficient of 0.9967 compared to GC grab sample analysis.

    By Turner Designs Hydrocarbon Instruments, Inc. based in Fresno, CALIFORNIA (USA).

  • Premium

    Continuous emissions monitoring for mercury monitoring

    Waste incinerators, cement plants and power plants need good and reliable measurements of total gaseous mercury. The measurement of total gaseous mercury is a challenge due to chemical reactions and contamination. The installed systems will often require a lot of maintanence still not giving reliable results.

    By Opsis AB based in Furulund, SWEDEN.

  • SO2 Monitoring in Air

    SO2 (sulfur dioxide) is measured in a number of applications. SO2 is used as a food grade preservative and must be regulated in accordance with government-set criteria to be safe for consumers. It is also measured in fuel exhaust to control for environmental pollution and in cement plants for process control.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Continuous Emission Monitoring

    By MRU Instruments, Inc. based in Houston, TEXAS (USA).

  • O2 Monitoring in Air

    Oxygen (O2) is a colorless odorless gas, essential to all life on Earth but damaging in high concentrations. An O2 analyzer should thus be employed for safety management and air pollution prevention purposes. LasIR MP110 is perfect for continuous emission monitoring of O2. It is based on TDLAS technology and can be calibrated as an O2 analyzer, providing accurate and reliable measurements. It quickly responds to changes in compound concentration, thus providing continuous emission monitoring for the specified...

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Premium

    Perimeter Ambient Air Monitoring

    Cerex Multi-Gas Open Path Analyzers are available in both FTIR and UVDOAS technologies to meet specific requirements for perimeter ambient air quality monitoring, leak detection, fugitive emissions monitoring and ambient air quality monitoring. Cerex multi-gas analyzers offer significant advantages over single gas analyzer arrays, electro-chemical sensor arrays and time integrated air sampling hardware

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Urban air quality monitoring

    To measure air quality in the ambient air is a challenge. The monitoring site needs to be representative and not dependant on changes in local traffic. A large number of gaseous components need to be measured with high accuracy and high availability.

    By Opsis AB based in Furulund, SWEDEN.

  • Opacity monitoring for continuous emissions

    The history of air pollution regulation dates back as far as the 13th century when in 1273, Edward I (Longshanks) of England prohibited the burning of sea coal in London. The smoke produced by its combustion was considered detrimental to human health. By the late 19th and early 20th centuries, regulations were being passed that sought to control air pollution predominantly for smoke and odour control. Traditionally, regulators were concerned with the visual impact of the discharge from a stack or chimney. Therefore...

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Premium

    Raw-gas monitoring for scrubber optimizing

    The consumption of scrubbing material in a scrubber is related to the mass flow of acid gases. Hydrogen chloride (HCl) and sulphur dioxide (SO2) are the major acid gases in an incinerator. By measuring the mass flow of SO2 and HCl in the raw gas going into the scrubber, it is possible to calculate the required quantity of scrubbing material.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous Metals Stack Monitor (CEMs)

    Cooper Environmental's Xact® 640 has the unique ability to generate high time resolution metals measurement in stacks. This unique capability has the potential to qualify as a substitution for the combination of a Hg/ PM CEMs application as well as the potential for a pollution control system feedback loop that could result in the reduction of pollution control consumables. Our systems have been site certified for compliance measurements at hazardous waste incinerator and secondary lead smelter sites.

    By Cooper Environmental Services based in Beaverton, OREGON (USA).

  • Premium

    Continuous emissions monitoring for brick plants

    Process control and emissions monitoring in a brick plant is a challenge due to the high concentrations of HF. The HF is generated in the process and gas phase HF can reach 50 mg/m3 or more. To use an extractive system in this environment will demand a lot of maintanence.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the...

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Continuous emissions monitoring for carbon capture and storage

    The process control of a CO2 capture plant needs good and reliable detection of gas phase NH3. Measuring NH3 is a challenge due to the corrosive environment and high concentrations of NH3. Several places in the process needs to be monitored and to transport the sample is difficult. A large dynamic range is needed as the NH3 concentration can vary between 15% volume and a...

    By Enviro Technology Services Ltd based in Stroud, UNITED KINGDOM.

  • Premium

    Ambient air monitoring by FID detection – airmoVOC BTEX

    Urban pollution is a problem that concerns more and more people in charge of public health. In large cities, car emissions are an important source of atmospheric pollution. This problem is growing as the traffic keeps on increasing. BTEX compounds are present in car emissions. It is therefore important to be able to analyze them with short analysis cycle duration and on a continuous and automatic way.

    By Chromatotec Group based in Val de Virvée, FRANCE.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you