Only show results available in Virginia? Ok

continuous emissions monitoring method Applications

  • Premium

    Continuous emissions monitoring for glass manufacturing

    Process control and emissions monitoring in a glass manufacturing plant is a challenge due to high temperature in the flue gas. The OPSIS DOAS system provides the glass industry with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method that uses an optical path to measure across the duct.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for steel mills

    The nature of steel manufacturing processes places severe limitations on the monitoring methods that can be used. Aggressive environments combined with high levels of particulates and gases make the choice very limited.

    By Opsis AB based in Furulund, SWEDEN.

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Opacity monitoring for continuous emissions

    The history of air pollution regulation dates back as far as the 13th century when in 1273, Edward I (Longshanks) of England prohibited the burning of sea coal in London. The smoke produced by its combustion was considered detrimental to human health. By the late 19th and early 20th centuries, regulations were being passed that sought to control air pollution predominantly for smoke and odour control. Traditionally, regulators were concerned with the visual impact of the discharge from a stack or chimney. Therefore, emission limits were expressed in terms of colour or opacity. Modern methods for opacity measurement still use the darkness of the stack gases to measure the amount of smoke or dust emitted within the exhaust gases.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Particulate monitoring for continuous emissions

    With the advent of specific process emission limits being defined, continuous particulate monitoring has become a regulatory requirement for many industries. smoke stack #1Particulate monitoring requires the measurement of the mass concentration of particulate matter in stack emissions to atmosphere. There is no known method of continuously measuring particulate concentration by direct measurement and therefore, all continuous particulate measurement methods are inferential. Each method involves the measurement of a parameter related to particulate concentration and then requires a calibration to be determined to convert the measured value into one of particulate mass concentration.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Premium

    Continuous emissions monitoring for mineral wool production

    Process control and emissions monitoring in a mineral wool plant is a challenge due to the presence of phenol and formaldehyde. To use an extractive system in this environment will demand a lot of maintenance. The OPSIS DOAS system is different and provides plants with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method using an optical measurement path that can operate across the duct.

    By Opsis AB based in Furulund, SWEDEN.

  • Continuous Monitoring of Groundwater

    The Sorbisense method allows for measuring the average concentration of substances in groundwater over a period of up to 1 month with only one sample.

    The system provides methods for measurements in both unsaturated and saturated zone and provides access to dynamic boundaries of contaminants and more realistic risk assessments. For example, through direct measurements of seepage from contaminants and by continuous measurement of emissions from cropland.

    By SORBISENSE based in Tjele, DENMARK.

  • Continuous Monitoring of Wastewater

    The Sorbisense method allows for efficient monitoring of the sewage system and can help reduce costs of operation and environmental impact. The method is particularly well suited for tracking the source of periodic discharges, the identification of faulty pipe connections of the measuring of values in the recipient. The method also allows for measurements in dynamic sources - such as emissions from roads, roofs, parking lots and overflow

    By SORBISENSE based in Tjele, DENMARK.

  • Premium

    Portable Stack Monitoring

    Many industries are required to measure stack emissions of toxic gases periodically, but not continuously. Extractive wet chemical methods currently used are slow, labor intensive and expensive. A single GasFinderFC can perform stack monitoring requirements for a specific gas, quickly, easily and accurately.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you