Only show results available in Virginia? Ok

continuous emissions testing Applications

  • Premium

    Monitoring solutions for the continuous emissions monitoring

    Multi-gas Stack Analyzers for Continuous Emissions Monitoring. FTIR and UVDOAS Analyzer Models available for Insitu Probe, Internal or External Cells, or Cross Stack Sample Acquisition.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Continuous emissions monitoring for mercury monitoring

    Waste incinerators, cement plants and power plants need good and reliable measurements of total gaseous mercury. The measurement of total gaseous mercury is a challenge due to chemical reactions and contamination. The installed systems will often require a lot of maintanence still not giving reliable results.

    By Opsis AB based in Furulund, SWEDEN.

  • Opacity monitoring for continuous emissions

    The history of air pollution regulation dates back as far as the 13th century when in 1273, Edward I (Longshanks) of England prohibited the burning of sea coal in London. The smoke produced by its combustion was considered detrimental to human health. By the late 19th and early 20th centuries, regulations were being passed that sought to control air pollution predominantly for smoke and odour control. Traditionally, regulators were concerned with the visual impact of the discharge from a stack or chimney. Therefore, emission limits were expressed in terms of colour or opacity. Modern methods for opacity measurement still use the darkness of the stack gases to measure the amount of smoke or dust emitted within the exhaust gases.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Continuous Emission Monitoring

    By MRU Instruments, Inc. based in Houston, TEXAS (USA).

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Premium

    Measurement solution for accurate continuous formaldehyde measurement formaldehyde in emissions and ambient air applications

    Formaldehyde (HCHO) is the simplest aldehyde species and is present, or generated by, many sources (both natural and industrial). It is classed as a substance that is toxic and harmful to human health.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Continuous emissions monitoring for palm oil plants

    Make more out of your mill. OPSIS tested and approved monitoring systems provide cost-effective and reliable on-line monitoring of several gas compounds, such as both high and low concentrations of methane, moisture, carbon dioxide and hydrogen sulphide, at several locations.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for power plants

    OPSIS offers fully automated system solutions for continuous monitoring in power plants. The monitoring systems have been tested and approved by the German TÜV and the U.S. EPA among others, for the best performance and longest calibration interval.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Measurement of hydrogen sulfide & carbon disulfide in air for continous emission monitoring

    The Series 8900 Hydrogen Sulfide and Carbon Disulfide Analyzer provides direct measurement of H2S and CS2 in ambient air. This instrument is utilized for continuous emission monitoring. The Series 8900 H2S and CS2 Analyzer employs a Photoionization detector (PID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is carried to the pre-cut column. Backflush is timed so that only the H2S, CS2, and other similar components are eluted to the analytical column. Contaminants on the pre-cut column are backflushed to vent. H2S and CS2 are separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By MOCON, Inc. - Baseline based in Lyons, COLORADO (USA).

  • Premium

    Gas Detection Solutions for GHG Monitoring

    Most sources of fugitive emissions are from multiple points rather than single point sources. So, open path area or perimeter monitoring provides more meaningful fugitive emissions data than an array of point sensors or a program of grab sampling. Point measurements may underestimate emissions because of missing locations with high gas concentrations, or conversely overestimate because they are located in areas of high concentrations. Grab sampling programs typically check only a small percentage of potential leak locations and extrapolate results to an entire facility. Wide margins of uncertainty are associated with such extrapolations. Open path monitoring provides continuously updated, real-time, integrated emissions across a facility boundary.This provides a complete picture of the fugitive emissions across that boundary,enabling identification of specific operations and times that give rise to higher emissions, and so enabling these emissions to be properly managed and controlled.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • CO2 / CO Monitoring in Air

    CO (carbon monoxide) and CO2 (carbon dioxide) are generally measured to ensure process control. CO2 is the desired product and CO is undesired in combustion since it will explode in high enough concentrations. CO2 and CO concentrations can also be used to determine other process-specific efficiencies. Continuous emissions monitoring equipment that can be calibrated as a CO and CO2 analyzer is thereby essential for process control.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Premium

    Measurement solution for to multi-stream by-pass system

    A large pharmaceutical plant runs a Thermal Oxidiser on plant to incinerate their solvent-containing gas streams before emission. When the oxidiser is offline, then the plant must monitor the release of solvent to the atmosphere. A ProtIR 204C fixed monitoring system was installed that continually measures 24 plant solvents, including Acetone, Cyclohexane, DCM, DMF, IPA, MIBK, Toluene and THF. Given the high levels that are possible, the system has an active dilution system, reducing the concentration of the measured gas in the analyser to levels that can be analysed simply. Chemometric modelling enables interferences from the overlapping absorption spectra to be accounted for, ensuring accurate analysis of all 24 gases.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Stack Testing for Rod Mill Exhaust Stack

    STEEL INDUSTRY: Conducted particulate testing and continuous emission monitoring of a rod mill exhaust stack. In addition, testing was performed to determine emissions associated with a slow cooling pen associated with ball mill production.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Stack Testing for Medical Waste Industry

    INFECTIOUS WASTE INDUSTRY: Provided annual testing for metals, particulate, HCl, dioxins/furans, and typical continuous emission monitoring constituents.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • O2 Monitoring in Air

    Oxygen (O2) is a colorless odorless gas, essential to all life on Earth but damaging in high concentrations. An O2 analyzer should thus be employed for safety management and air pollution prevention purposes. LasIR MP110 is perfect for continuous emission monitoring of O2. It is based on TDLAS technology and can be calibrated as an O2 analyzer, providing accurate and reliable measurements. It quickly responds to changes in compound concentration, thus providing continuous emission monitoring for the specified gas.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the directives and regulations set. Two major parts of this on-going quality assurance cycle are the QAL2 and AST procedures. A test laboratory performs tests on the systems on-site, and determines whether the systems fulfill the set requirements or not.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Stack Testing for Sewage Sludge Incinerators

    SEWAGE TREATMENT INDUSTRY: Provided Incinerator Performance Testing Services and Relative Accuracy Testing of a Continuous Emission Monitoring system associated with sewage sludge incinerator.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • Premium

    Ambient air monitoring by FID detection – airmoVOC BTEX

    Urban pollution is a problem that concerns more and more people in charge of public health. In large cities, car emissions are an important source of atmospheric pollution. This problem is growing as the traffic keeps on increasing. BTEX compounds are present in car emissions. It is therefore important to be able to analyze them with short analysis cycle duration and on a continuous and automatic way.

    By Chromatotec Group based in Val de Virvée, FRANCE.

  • Premium

    Flow meters for the environmental flow solutions

    Our flow measurement technology is ideal for applications ranging from landfill emissions to wastewater treatment and numerous applications in between. We have developed many flow meters and controllers to measure the emissions from landfills and other green house gas producers, in addition to being a long standing leader in the testing of emissions for large engines. Water treatment is also an important driver for the company as we continue to develop innovative solutions for waste water treatment.

    By Sierra Instruments, Inc. based in Monterey, CALIFORNIA (USA).

  • Premium

    Industrial Solution for incineration & thermal treatment

    Waste incineration, including solid municipal and hazardous waste, biomedical waste and hazardous liquid are all continually under more stringent scrutiny by regulators. Macrotek has designed and supplied many integrated systems to meet most guidelines. In several installations, hazardous waste has been combined with radioactive waste, requiring nearly non-detectable emission levels for many of the contaminants. Macrotek has installed and tested systems for these processes with the results significantly better than required standards.

    By Macrotek Inc. based in Markham, ONTARIO (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you