Only show results available in Virginia? Ok

continuous gas analyzer Applications

  • Gas detection analyzers for semiconductor industry

    Semiconductor manufacturing facilities employ a number of hazardous gases in their production processes. Whenever these gases are stored, distributed or used in manufacturing processes, there exists the potential for a hazardous condition. The primary hazards associated with these gases include fire, explosion, and contamination resulting in product loss or unscheduled preventative maintenance. These gases must be continuously monitored to ensure the health and safety of employees, to protect property, as well as to maintain regulatory compliance. Continuous gas monitoring in semiconductor facilities is a requirement of local and state regulations.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Gas detection analyzers for chemical & pharmaceutical processes

    Chemical and pharmaceutical facilities use a variety of hazardous gases and solvents in their production processes. Whenever these substances are transported, processed or stored, the potential risks are high for hazardous conditions. These substances must be continuously monitored to protect personnel and facilities from accidental releases or leakage. Our various lines of hazardous gas monitoring systems benefit the chemical and pharmaceutical industry in the following applications.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Gas detection analyzers for wastewater treatment industry

    Regulations prohibit facilities from discharging flammable or explosive wastes from their processes into the wastewater collection system. These wastes are not only a fire and explosion hazard but they can also effect the efficient and effective operation of the treatment facility. PrevEx Flammability analyzers are used to continuously monitor the waste stream for flammable gases and vapors. Their unique design and operating technology make them the ideal analyzers for the harsh conditions found in the sewer environment.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Premium

    Gas analysis & monitoring system for biogas analysis

    “Biogas” means a mixture of various types of gas (mostly methane) produced by bacterial fermentation in anaerobic conditions(absence of oxygen) of organic residues from waste, decaying plant, carcasses in putrescence. The analyzers of biogas by Infrared cells carry out the continuous analysis of CH4, O2, CO2, H2S and NH3. The whole process sees the decomposition of organic material by some types of bacteria, producing carbon dioxide, molecular hydrogen and methane(methane conversion of organic compounds).

    By ETG Risorse e Tecnologia based in Montiglio, ITALY.

  • Premium

    Gas monitoring instruments and systems for phosgene monitoring

    Phosgene COCl2 is a colorless gas. While it has been used as a Chemical Weapon Agent (CWA) in the past, currently this poisonous gas is also an important reagent in synthesis in the pharmaceutical and chemical industries. The plants using phosgene are typically equipped with gas sensors to detect leaks in the indoor ambient air. The critical situations arise when equipment in contact with the gas at the manufacturing facilities are serviced and maintained. As phosgene is very poisonous, even small gas pockets in serviced equipment may be dangerous to maintenance personnel. Gasmet™ FTIR Gas Analyzers are ideal tools to monitor point sources of phosgene. The measurement technology has high specificity, may be operated continuously, and has a fast response time.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Capabilities of the Adsorbent Tube Injector System (ATIS™)

    The Adsorbent Tube Injector System (ATIS) was developed at Supelco® by R&D Scientists, as a tool to assist in our comprehensive adsorbent research for thermal desorption tubes. The ATIS provides an efficient means of transferring calibration standards in either the gas or liquid phase onto the adsorbent packed tubes. The ATIS employs the technique of flash vaporization to vaporize the sample in a continuous flow of inert gas; the inert gas carries the sample to the tube. The sample pathway of the ATIS is constructed of glass and stainless steel. The calibration standard is injected by a syringe through a replaceable septum in the center of the injection glassware, which is heated. After enough time has elapsed, typically less than five minutes, the tube is removed from the ATIS and analyzed using the appropriate analytical technique for that adsorbent tube.

    By Sigma-Aldrich Co., LLC based in Bellefonte, PENNSYLVANIA (USA).

  • O2 Monitoring in Air

    Oxygen (O2) is a colorless odorless gas, essential to all life on Earth but damaging in high concentrations. An O2 analyzer should thus be employed for safety management and air pollution prevention purposes. LasIR MP110 is perfect for continuous emission monitoring of O2. It is based on TDLAS technology and can be calibrated as an O2 analyzer, providing accurate and reliable measurements. It quickly responds to changes in compound concentration, thus providing continuous emission monitoring for the specified gas.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • CH4 Monitoring in Air

    CH4 (Methane) is a colorless, odorless natural gas that is used in a wide variety of industrial applications such as power generation and chemical production. It is also a byproduct of many biological and geological processes, fracking, and gas drilling. It is highly flammable and creates amounts of carbon monoxide as its combustion byproduct. Methane needs constant monitoring in waste water treatment (for co-generation) and to ensure proper process control (e.g. to determine burning efficiency). A quality CH4 analyzer that is able to provide continuous monitoring is a perfect solution for this.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • HCl Monitoring in Air

    Hydrogen chloride (HCl) is a colorless, sometimes slightly yellow, gas. It is an undesired environmental component that may be damaging to workers and the surroundings. Exposure limits have thus been established by industries to make sure that the workers operate in a safe environment. HCl monitoring is especially required for incinerators, coal-fired power plants, aluminum recycling and cement plants. Unisearch offers a reliable and easy-to-use HCl analyzer – the TDLAS-based LasIR system. Studies have shown that TDLAS equipment provides data that is more accurate than conventional gas monitoring equipment. When calibrated for HCl monitoring, TDLAS is able to detect this gas among other gases present in the area and provide continuous updates with regards to the changes in its concentration.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you