Only show results available in Virginia? Ok

continuous level monitoring Applications

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Premium

    Continuous emissions monitoring for steel mills

    The nature of steel manufacturing processes places severe limitations on the monitoring methods that can be used. Aggressive environments combined with high levels of particulates and gases make the choice very limited.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Measurement and control systems for the controlling the level - electronically

    Discontinuous control is used mainly in smaller steam boilers with low output since the temperature fluctuations in the boiler are fairly great as a result of irregular refilling with water. Continuous control, on the other hand, permits still more economical steam generation with high quality.

    By IGEMA GmbH based in Münster, GERMANY.

  • Premium

    Radiation Monitoring for Environmental Monitoring

    The environment is one of today’s foremost concerns, and its preservation is among the biggest challenges we need to meet in coming years. Saphymo offers a series of global solutions designed to detect the impact of a nuclear accident on the environment and local populations, and hence facilitate crisis management. Our environmental monitoring networks and mobile devices continuously monitor artificial and natural radiation levels in air, water and soil, and provide data transmission to a central supervision station. These solutions are internationally acclaimed for their autonomy, reliability, and ability to resist harsh environmental conditions.

    By Saphymo based in Montigny Le Bretonneux, FRANCE.

  • Premium

    Environmental radiation monitoring

    Every day, wherever we go, we are exposed to minute amounts of environmental radiation.* This environmental radiation is emitted continuously, day and night, from various objects and substances in the natural world and our living environment.

    Most environmental radiation consists of three types: alpha rays (α), beta rays (β) and gamma rays (γ).  HORIBA`s PA-1000 `Radi` environmental radiation monitor makes it easy for non-specialists to measure even minute levels of gamma rays.

    * Environmental radiation, also known as natural radiation, includes radiation emitted from space, soil, stones, the ground and the air, as well as from manmade objects such as concrete and buildings

    By HORIBA Europe GmbH based in Leichlingen, GERMANY.

  • Biogas monitoring

    meet governmental regulations, it is important to accurately monitor methane gas production, removal, venting, and burning. Knowledge of both methane flow and temperature at the flare stack can define when CH4 is being emitted to the atmosphere. The DX99 FlexPower™ Nodes can be installed in EX area with a Zone 0 ATEX certification. Use the analogue input to determine methane production levels and flow and use the thermocouple model to measure the temperature of a vent to verify the continuous combustion of methane.

    By Banner Engineering Corp. based in Diegem, BELGIUM.

  • Low frequency noise analysis using XL2

    The Data Explorer PC software for the XL2 Sound Level Meter now includes a series of professional tools for detailed analysis of low-frequency noise (LFN). The graphical representation of time varying frequency components offers an efficient process for identifying the presence and level of LFN. Also the associated high quality audio recording supports further correlation with the objective measurement data. The new features are particularly useful in the calculation of immission levels which is defined as the cumulative noise energy to which an individual is exposed over time. Exposure to low-frequency noise over extended periods can lead to a range of health problems including cardio vascular disease, insomnia and depression. The sources of low frequency noise can often be attributed to electricity sub stations, chiller plants and incinerators with continuous noise at frequencies below 200 Hz. XL2 Sound Level Meter records all Data Measuring LFN requires a class 1 sound level meter

    By NTi Audio AG based in Schaan, LIECHTENSTEIN.

  • Pollutant monitoring for the manufacturing industries

    Ormantine`s air monitoring equipment is widely used to monitor both indoor and outdoor air quality. Continuous development allows us to provide equipment for a broad range of applications, covering short-term and long-term monitoring. Pollutants can be detected even at very low levels – limits of detection are typically in the low parts per billion (ppb) range. Ormantine USA`s many solutions have applications from personal exposure monitoring to long term fence line monitoring studies.

    By Ormantine USA Ltd., Inc. based in Palm Bay, FLORIDA (USA).

  • Premium

    Measurement solution for high NH3 monitoring from wastewater

    Protea was asked to supply a high level ammonia (NH3) measurement system for a waste water treatment plant. The reflux drums at the inlet to two ammonia stripping towers needed to be measured continuously. Protea designed a solution based around our Solus TDLAS analyser platform and a high level dilution system. The Solus analyser was configured for NH3 measurements in the range 0-500ppm. A dilution system incorporating special dilution probe and 19` control panel was installed before the analyser. This gave a dilution level of 600:1, enabling the NH3 analyser to measure in the range 0-30% Volume.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Measurement solution for to multi-stream by-pass system

    A large pharmaceutical plant runs a Thermal Oxidiser on plant to incinerate their solvent-containing gas streams before emission. When the oxidiser is offline, then the plant must monitor the release of solvent to the atmosphere. A ProtIR 204C fixed monitoring system was installed that continually measures 24 plant solvents, including Acetone, Cyclohexane, DCM, DMF, IPA, MIBK, Toluene and THF. Given the high levels that are possible, the system has an active dilution system, reducing the concentration of the measured gas in the analyser to levels that can be analysed simply. Chemometric modelling enables interferences from the overlapping absorption spectra to be accounted for, ensuring accurate analysis of all 24 gases.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Mercury monitoring for on-site remediation

    Fugitive emissions can be a health concern during removal and disposal of mercury-contaminated material at remediation sites. Thus, remediation projects either indoors or outdoors often require on-site, real-time mercury air monitoring with a Tekran 2537. This assures permitted levels are not exceeded during waste processing and human exposure levels are below government regulated toxicity thresholds. Often multiple sites must be monitored continuously. The Tekran 1115 Multi-Port Sampler is the ideal tool for multiplexing the Tekran 2537 for real-time continuous on-site monitoring of mercury fugitive emissions. Please contact us for more information on mercury remediation monitoring.

    By Tekran Instruments Corporation based in Knoxville, TENNESSEE (USA).

  • Premium

    Online Monitoring for the Drinking Water Industry

    AppliTek manufactures wet-chemical analyzers specifically designed for measuring on a continuous base the quality indices of drinking water, from raw water intake up to distribution level. Our systems have a small footprint, reduced reagent consumption and show excellent levels of detection in compliance with modern standards.

    On top of that, the delivery of safe water throughout the water cycle will raise the need for efficient monitoring systems detecting in real-time contaminations. `Broadband toxicity`, a non-specific parameter defined by AppliTek, is a prodigiously new and clean technology for safeguarding drinking water.

    By AppliTek NV based in Nazareth, BELGIUM.

  • Noise and vibration monitoring for oil and gas industry

    The oil and gas industry requires major infrastructure in terms of refineries and offshore extraction platforms which operate continuously. A large number of essential rotating machines, structures and piping networks are subjected to high levels of demand in a difficult environment, leading to the potential for breakage.

    By ACOEM based in Limonest, FRANCE.

  • Air monitoring equipments for outdoor & indoor air quality

    Gradko’s ambient air monitoring equipment is widely used to monitor both indoor and outdoor air quality. Continuous development allows us to provide equipment for a broad range of applications, covering short-term and long-term monitoring. Pollutants can be detected even at very low levels – limits of detection are typically in the low parts per billion (ppb) range.

    By Gradko International Ltd based in Winchester, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you