Only show results available in Michigan? Ok

cyclone separator Applications

  • Premium

    Emission control solutions for Glass and ceramic furnaces sector

    Glass and ceramic furnacesare typically associated with emissions of very fine particles (< 5 µm) in combination with high temperatures and load. An increasingly higher number of furnaces are powered with biomass fuel, further raising the level of particulate emissions that need to be treated, in order to comply with stricter regulatory limits. Solving this problem may or not require a two stage dedusting system such a cyclone pre-separation system followed by an ESP. Client`s needsfrequently include a...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Industrial chemical solutions for the petrochemical industry

    Petrochemicals, also called petroleum distillates, are chemical products derived from petroleum. Petrochemicals are used to produce industrial chemicals, plastics products, synthetic rubber, dyes, synthetic detergents, polyurethanes, synthetic fibers, ammonia, and methanol. Chemical handling and emissions abatement are critical processes with stringent environmental standards.

    By CECO Environmental based in Dallas, TEXAS (USA).

  • Premium

    Emission control solutions for pyrolisis, incineration and gasification sector

    For PM emission control in very high temperature exhaust streams ( >600ºC ), such as gasification, pyrolysis and incineration, traditional bag filters following temperature exchangers, ceramic filters, or scrubbers are used as end stage dedusters. For most arrangements, a primary high temperature separator, namely a cyclone, is important to reduce as much ash and char as possible. A good efficiency is important to reduce concentration of solids to the final stage dedusters, avoiding plugging of scrubbers...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Emission control solutions for calcination processes sector

    In calcination processes, solid intermediates and products are regularly handled in the fine powder form (ex: kaolin or metakaulin). There is a need to separate these very fine powders from the exhaust streams of calciners, fluid bed dryers or incinerators, often at critical temperature conditions. For PM emission control at very high temperature ( >600 ºC), traditional bag filters following temperature exchangers or scrubbers are used as end stage dedusters.

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Product recovery solutions for chemicals industry

    Efficient recovery of active pharmaceutical ingredients (APIs), chemical substances or food powders after drying applications such as spray and fluid bed drying is frequently a problem. The same problem occurs in many milling and micronization applications. The preferred way to recover these sensitive products is with cyclone collectors due to their direct powder capture. Unlike bag filters or wet scrubbers, cyclones minimize filter or product contamination and product cross contamination and can easily handle a...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Product recovery solutions for pharmaceutical ingredients industry

    Efficient recovery of active pharmaceutical ingredients (APIs), chemical substances or food powders after drying applications such as sprayand fluid bed dryingis frequently a problem. The same problem occurs in many milling and micronization applications. The preferred way to recover these sensitive and expensive products is with cyclone collectors due to their direct powder capture. Unlike bag filters or wet scrubbers, cyclones minimize filter or product contamination and product cross contamination and can...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Product recovery solutions for food ingredients industry

    Efficient recovery of active pharmaceutical ingredients(APIs), chemical substances or food powdersafter drying applications such as spray and fluid bed dryingis frequently a problem. The same problem occurs in many milling and micronization applications. The preferred way to recover these sensitive products is with cyclone collectors due to their direct powder capture. Unlike bag filters or wet scrubbers, cyclones minimize filter or product contamination and product cross contamination and can easily handle a...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    High-tech energy solution for semiconductor and circuit manufacturing industry

    Plants within the semiconductor and circuit manufacturing industry deals manufacture semiconductors, computers, printed circuit boards, and other very small electronic components, including transistors, capacitors, inductors, resistors, diodes, insulators and conductors. Semiconductor manufacturing process emissions and pollution control challenges include VOC abatement; acid gas scrubbing; fluid handling; filtration; and laboratory fume hood exhaust.

    By CECO Environmental based in Dallas, TEXAS (USA).

  • Premium

    Metals & mining solutions for the mining & quarries industry

    Mining & Quarrying involves the extraction of valuable minerals or other geological materials from the earth, including metals, coal, oil shale, gemstones, limestone, dimension stone, rock salt, potash, gravel, and clay. CECO has the proven expertise to deliver proven products and systems for a wide range of emission control, air filtration and fluid handling challenges including volatile organic compound (VOC) abatement systems; dampers and expansion joints; dry particulate filtration; industrial dust, fume,...

    By CECO Environmental based in Dallas, TEXAS (USA).

  • Hydrocyclones for chemical plants applications

    KREBS hydrocyclones, including Krebs gMAX hydrocyclones, are simple, yet highly effective equipment for removing and / or concentrating solids in chemical processes.

    By FLSmidth based in Tucson, ARIZONA (USA).

  • Bag Filter Plants

    Triboelectric dust probes installed in the clean gas duct after bag filters, cartridge filters or centrifugal separators (cyclones) are used to detect faulty, damaged or leaking filters. This early detection of failures minimises product loss, improves environmental conditions and problematic dust emissions. Benefits include low initial outlay, no consumables and low maintenance requirements. There are more than 10,000 Dr. Foedisch filter monitor devices installed worldwide in the food processing, cement,...

    By CEM Solutions (UK) Ltd. based in Darley Dale, UNITED KINGDOM.

  • Hydrocyclones for quench water treatment

    Cost Effective Protection with KREBSs Hydrocyclones for Quench Water Treatment. High Efficiency products to remove mill scale in steel plants and metal forming applications.

    By FLSmidth based in Tucson, ARIZONA (USA).

  • Industrial dedusting

    The industrial dedusting field is very varied and branches out in numerous specialized branches. For a preliminary examination of the problem it is necessary to dispose of two series of data: characteristics of the system which emits the pollutants; nature of pollutants and their characteristics.

    By GGE srl based in Rio Saliceto, ITALY.

  • KREBS CP Cyclone Vessels & DeSanders for Automotive - Paint & Cleaning Processes

    KREBS cyclones are used in automotive and large vehicle plants. Krebs cyclones improve the cleaning process prior to painting by separating the paint weld balls, metallic particles, oils, grease and phosphate sludge from the cleaning solution.

    By FLSmidth based in Tucson, ARIZONA (USA).

  • Hydrocyclones for sewage & waste water treatment applications

    FLSmidth Krebs Hydrocyclones and Close Packed Cyclones provide a more efficient and less expensive option to remove grit, sand, and other solids from sewage/water than gravity sedimentation systems.

    By FLSmidth based in Tucson, ARIZONA (USA).

  • KREBS® Pulp Cleaner -High Density Stock Cyclone

    KREBS® high density stock cleaners (pulp cleaner cyclones) are designed to withstand corrosion, high temperatures, and heavy loads of abrasive materials such as glass, staples, and wire.

    By FLSmidth based in Tucson, ARIZONA (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you