Only show results available in Virginia? Ok

dust emissions Applications

  • Premium

    Emissions Monitoring for Mining / Emissions Monitoring for Smelting

    The Opsis monitoring solution for mining and smelting applications is based on either DOAS or laser diode technique. Opsis non-contact monitoring solutions are very well suited for applications in the Mining and Smelting Industries, as the flue gas conditions often involves high temperatures and high dust concentrations. The on-line, open-path systems are used for monitoring HF, sulphur dioxide, SO3 and HCl in potrooms, in fence-line applications and in continuous emissions monitoring.

    By Opsis AB based in Furulund, SWEDEN.

  • Gas monitoring and dust monitoring

    EM-5 series Continuous Emission Monitoring System (CEMS) Counting tail gas emission and realtime concentration NOX SO2 O2 Temperature pressure flow dust

    By HANGZHOU ZETIAN TECHNOLOGY CO., LTD based in Hangzhou, CHINA.

  • Premium

    Gas monitoring and dust monitoring for the powerplants industry

    LaserGas measurements

    • Boiler combustion control, O2 and CO
    • DeNOx system, NH3 and NO
    • Electrostatic precipitators (ESP), CO monitoring for explosion prevention
    • Stack gas emissions, NH3, H2O, NO
    • Coal silos, CO monitoring for explosion prevention and detection of smouldering fires (only in coal fired plants)

    LaserDust measurements

    • Stack gas emission
    • Coal silo, explosion prevention

    By NEO Monitors AS based in Skedsmokorset, NORWAY.

  • Premium

    Stack emissions monitoring

    Monitoring stack emissions is a fundamental requirement for most industrial processes. Our gas analysers, dust monitors and flow monitors are designed for a wide range of applications and can operate as a fully integrated system or as stand alone instruments.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Electrostatic Precipitator

    An electrostatic precipitator (ESP), or electrostatic air cleaner is a particulate collection device that removes particles from a flowing gas (such as air) using the force of an induced electrostatic charge. Electrostatic precipitators are highly efficient filtration devices that minimally impede the flow of gases through the device, and can easily remove fine particulate matter such as dust and smoke from the air stream.[1] In contrast to wet scrubbers which apply energy directly to the flowing fluid medium, an ESP applies energy only to the particulate matter being collected and therefore is very efficient in its consumption of energy (in the form of electricity).

    By MEVADHASHMA based in Coimbatore, INDIA.

  • Premium

    Gas monitoring and dust monitoring for the cement industry

    LaserGas measurements

    • Preheater exit, CO monitoring
    • Electrostatic precipitators (ESP) after pre-heaters, CO monitoring for explosion prevention
    • Coal silo, CO monitoring
    • Exit of coal mill, dust filter, CO monitoring
    • Stack gas emissions, HCl and HF

    LaserDust measurements

    • Stack gas emissions
    • Coal silo, explosion prevention

    By NEO Monitors AS based in Skedsmokorset, NORWAY.

  • Premium

    Continuous emissions monitoring for chemical industry

    Process control and emissions monitoring in a chemical plant is a challenge due to corrosive gases, high dust load, and high temperatures. To use an extractive system in this environment will demand a lot of maintenance.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for mining & smelting

    OPSIS non-contact monitoring solutions, based on either DOAS or TDL techniques, are very well suited for applications in the mining and smelting Industries, as the flue gas conditions often involve high temperatures and high dust concentrations.

    By Opsis AB based in Furulund, SWEDEN.

  • Gas monitoring and dust monitoring

    Laser gas instruments Pulverized coal bunker, Exit of preheater, Main emission chimney, Cooler,exhaust emission chimney, O2, CO, CO2

    By HANGZHOU ZETIAN TECHNOLOGY CO., LTD based in Hangzhou, CHINA.

  • Continuous emissions monitoring for mining industry

    Opsis non-contact monitoring solutions are very well suited for applications in the mining Industry, as the flue gas conditions often involve high temperature and high dust concentrations.

    By Enviro Technology Services Ltd based in Stroud, UNITED KINGDOM.

  • Biomass Plant Emissions Monitoring (CEMS)

    Procal´s analysers are used extensively in reporting and control applications in modern Biomass plants. The flexible and reliable instruments form the heart of the systems, enabling CO, NO2, NO, SO2, H2O, CO2, O2, dust and velocity to be measured.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Premium

    Emission Control Systems for Storage and Loading Areas

    The amount of dust generated when storing and moving various materials, such as wood, coal and ore, is very high and poses a severe health hazard. EmiControls offers customized solutions for dust control, thereby creating a pleasant, healthy and safe environment for workers and nearby residents. Fixed dust control installations on funnels, conveyor belts and at discharge points are just as suitable for use as mobile units – the right solution to any given problem is identified during the planning and consultation phase.

    By EmiControls based in Bolzano, ITALY.

  • Air Quality & Emission Management Issues

    • Development of documents substantiating the volumes of emissions of pollutants into the air from stationary sources for enterprises, organizations and private entrepreneurs; • Inventory of air pollutants emissions from stationary sources; • Preparing, maintenance support of documentation for receiving a Permit for Emissions of Pollutants into the Air from Stationary Sources (PEPASS) *, issued by the Departments of Environment and Natural Resources of the regional state administrations of Ukraine; • Development and registration of dust and gas cleaning equipment passports; • Monitoring of the dust and gas cleaning equipment effectiveness; • Quality control of the implementation of projects of Maximum Permissible Emissions (MPE); • Calculation of fees for environmental pollution (environmental tax) on the basis of amount of emission of pollutants into the air.

    By PP `Tehnologia O` based in Vinnytsia, UKRAINE.

  • Premium

    Emission Control Systems for Opencast Mines and Quarries

    High volumes of dust, often extending over large areas, present a major challenge for the operators of opencast mines and quarries. If conditions are also dry and windy, the dust will affect not only the workforce but also, in many cases, entire housing estates in the vicinity. The sources of dust in surface mining areas are often distributed over very large expanses, with dust originating from various places. With their large projection range, EmiControls dust controllers are ideal for such applications. Mobile versions of the machines can be moved easily and therefore used to control dust at various sources. Individually adapted spray systems can also be used in this field of application. The system in any given case can be controlled by a computer, thanks to the user-friendly software.

    By EmiControls based in Bolzano, ITALY.

  • Premium

    Emission Control Systems for Recycling and Composting Industry

    The treatment processes in recycling plants generate unpleasant and often harmful dust, which is a health hazard not only for nearby residents, but particularly for the employees. More and more legislation is being passed on dust control requiring such in the form of mobile units or fixed installations. In composting processes, the dust problem is compounded by unpleasant odors, which can be controlled effectively with specialized equipment. The same units are also used in biogas plants or for the removal and disposal of contaminated soil from industrial sites.

    By EmiControls based in Bolzano, ITALY.

  • Premium

    Emission Control Systems for Demolition Industry

    Demolition work and the dust it generates is a big problem for residents and the environment when work is carried out in residential areas. EmiControls offers the right dust control solution for every type of demolition work, thereby protecting the inhabitants, neighboring buildings and the environment. Because the source of dust can move constantly during the demolition process, mobile solutions are ideal as they can be positioned and pivoted easily and quickly. And they can be removed from the site when the work is completed.

    By EmiControls based in Bolzano, ITALY.

  • Odour & emission control for muncipal landfills

    Mechanical barriers that seal in odors, volatile organic compounds (VOCs), volatile nitrogen compounds (such as ammonia), volatile sulfur compounds (such as H2S) and, of course, fugitive dusts in municipal landfills.

    By Rusmar Inc. based in West Chester, PENNSYLVANIA (USA).

  • Opacity monitoring for continuous emissions

    The history of air pollution regulation dates back as far as the 13th century when in 1273, Edward I (Longshanks) of England prohibited the burning of sea coal in London. The smoke produced by its combustion was considered detrimental to human health. By the late 19th and early 20th centuries, regulations were being passed that sought to control air pollution predominantly for smoke and odour control. Traditionally, regulators were concerned with the visual impact of the discharge from a stack or chimney. Therefore, emission limits were expressed in terms of colour or opacity. Modern methods for opacity measurement still use the darkness of the stack gases to measure the amount of smoke or dust emitted within the exhaust gases.

    By DynOptic Systems Ltd based in Brackley, UNITED KINGDOM.

  • Premium

    Monitoring solutions for the flow monitoring areas

    Many large combustion plants are now required to monitor mass emissions of major pollutants and to do so requires an accurate measurement of stack gas velocity. The VCEM 5100 is certified to EN 15267 part 3 QAL 1 for all industrial processes including waste incineration. It has several key advantages, firstly the sensors optics are not in contact with the hot and dusty environment, the VCEM 5100 can monitor gases at temperatures exceeding 10000C and the analyser requires minimal maintenance. The VCEM 5100 can be used in extremely dust environments such as SCR’s when dust loadings exceed 10g/m3. The VCEM 5100 is in full compliance with EN/ISO 16911 part 2.

    By Codel International Ltd based in Bakewell, UNITED KINGDOM.

  • Air Pollution Removal Orthopedic appliances Industry

    Removal of acid gases and NOx from material surface treatments. Remove titanium dust from grinding, abrasive polishing and buffing operations. Emissions from high temperature furnaces.

    By Bionomic Industries Inc. based in Mahwah, NEW JERSEY (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you