For large combustion plants and power plants we offer the DCEM 2100 particulate monitor. This monitor is certified to EN 15267 part 3 QAL 1 for all industrial processes including waste incineration. It offers outputs in Transmission, Opacity and mg/m3 (when calibrated against a Standard Reference Method). The DCEM 2100 offers real-time zero and span calibration and an efficient air purge system to prevent optical contamination.
The frequency and intensity of dust and sand storms in many parts of the world are steadily increasing due to droughts and climate change. The severity of such storms is anticipated to increase over the coming years.
These dust storms may last hours or days and cause huge damage and imposed a heavy toll on society with its physical effects, such as visibility reduction, heavy winds, red sky, hailstone and severe lightning.
Such Dust storms, have a negative impact on human health, and industrial products and...
Boiler combustion control, O2 and CO
DeNOx system, NH3 and NO
Electrostatic precipitators (ESP), CO monitoring for explosion prevention
Stack gas emissions, NH3, H2O, NO
Coal silos, CO monitoring for explosion prevention and detection of smouldering fires (only in coal fired plants)
Stack gas emission
Coal silo, explosion prevention
Particulate matter, suspended particulate matter, atmospheric dust, particulate matter, total suspended particulate (TSP), are terms that commonly identify the group of substances suspended in the air (fibers, carbon particles, metals, silica, polluting liquid or solid). Particulate matter is the pollutant that is now considered the greatest impact in urban areas, and is composed of all those solid and liquid particles dispersed in the atmosphere, with a diameter ranging from a few nanometers to 500 microns and...
Monitoring stack emissions is a fundamental requirement for most industrial processes. Our gas analysers, dust monitors and flow monitors are designed for a wide range of applications and can operate as a fully integrated system or as stand alone instruments.
The Cleanroom is a combined laboratory chemical, mechanical and / or electronic whose main characteristic is the presence of very pure air, that is a very low content of fine dust in suspension. In the process of semiconductor production, the airborne particles (micro-powder) go to irreparably damage the micro-photoetched that form the chip, creating an electronic circuit defective, and then discarded. This process has forced the improvement of industrial production environments, removing particles from the air,...
The Opsis monitoring solution for mining and smelting applications is based on either DOAS or laser diode technique. Opsis non-contact monitoring solutions are very well suited for applications in the Mining and Smelting Industries, as the flue gas conditions often involves high temperatures and high dust concentrations. The on-line, open-path systems are used for monitoring HF, sulphur dioxide, SO3 and HCl in potrooms, in fence-line applications and in continuous emissions monitoring.
Evaporative gas cooling and conditioning systems help protect your downstream equipment, enhance air pollution control performance, reduce gas volumes, and increase production capacity. Central to our systems are Turbotak atomizing nozzles, which introduce a controlled amount of finely atomized water into the hot gas stream to reduce and/or maintain gas temperature. The water evaporates, while absorbing heat from the gases, for free-flowing dust, zero liquid discharge, and minimal or no wall buildup.
Process control and emissions monitoring in a chemical plant is a challenge due to corrosive gases, high dust load, and high temperatures. To use an extractive system in this environment will demand a lot of maintenance.
Duct (HVAC) cleaning is an important part of maintaining good air quality in any building, if ducts are not being cleaned properly, air polluted by dust and other fine particles that can be harmful, will be circulated throughout the system. The best way to ensure ducts are being cleaned completely is to visually inspect them, this can now be accomplished using HVAC inspection cameras. These CCTV cameras are composed of a digital inspection camera attached to a push rod to enable the camera to access all parts of...
By Medit Inc.
based in Winnipeg, MANITOBA (CANADA).
Procal´s analysers are used extensively in reporting and control applications in modern Biomass plants. The flexible and reliable instruments form the heart of the systems, enabling CO, NO2, NO, SO2, H2O, CO2, O2, dust and velocity to be measured.