Only show results available in Virginia? Ok

emission control system Applications

  • Premium

    Emission control & air dedusting for steel and ferrous alloys

    teel and ferrous alloys production happens in industrial manufacturing processes which involve high temperature exhaust streams, often at more than 900 ºC. Typically, the gas flows into a gas conditioning tower to cool down to approximately 200 ºC, before entering into an ESP. These flue gases from steel or ferrous alloys kilns are also very maintenance demanding for bag filters and the very small size of the particles limit the use of usual dedusters such as regular cyclones and multicyclones as pre-separators. Bag filter failure is consequently a very common problem for clients in this industry. 

    Client`s needs include a very robust dedusting system, either serving as end-stage collector avoiding the need to cool down flue gases, or strongly minimizing the loads of aggressive material to bag filters. 

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Emissions testing for engines

    Rich-burn engine exhaust, when uncontrolled, can have wide concentration ranges and both CO and NOX can fluctuate significantly. The on-board CO dilution system will automatically set-up for optimum testing, perfect for a rich burn engine. Lean-burn engines have different exhaust characteristics, but NO2 can make up a significant portion of the total NOX measurement. The 350 measures both NO and NO2 for proper lean-burn engine set-up. Due to high concentration, replaceable interference filters keep the sensors stable and your readings accurate. High exhaust pressures and heavy particulate loading are easily controlled with the special pressure relief valve (standard) on the engine probe configuration.

    By Testo Inc. based in Sparta, NEW JERSEY (USA).

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Premium

    Continuous emissions monitoring for aluminium smelters

    Process control and emissions monitoring in an aluminium smelter is a challenge due to the high concentrations of HF. To use an extractive system in this environment will demand a lot of maintenance.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Emissions Monitoring for Waste Incineration

    The in situ Opsis system is designed to meet the requirements from the new EC directive for monitoring stack emissions and for process control purposes in waste incinerators.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for chemical industry

    Process control and emissions monitoring in a chemical plant is a challenge due to corrosive gases, high dust load, and high temperatures. To use an extractive system in this environment will demand a lot of maintenance.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for glass manufacturing

    Process control and emissions monitoring in a glass manufacturing plant is a challenge due to high temperature in the flue gas. The OPSIS DOAS system provides the glass industry with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method that uses an optical path to measure across the duct.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for brick plants

    Process control and emissions monitoring in a brick plant is a challenge due to the high concentrations of HF. The HF is generated in the process and gas phase HF can reach 50 mg/m3 or more. To use an extractive system in this environment will demand a lot of maintanence.

    By Opsis AB based in Furulund, SWEDEN.

  • Biomass Plant Emissions Monitoring (CEMS)

    Procal´s analysers are used extensively in reporting and control applications in modern Biomass plants. The flexible and reliable instruments form the heart of the systems, enabling CO, NO2, NO, SO2, H2O, CO2, O2, dust and velocity to be measured.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Premium

    Gas monitoring instruments and systems for DeNOx process control

    In most combustion process atmospheric nitrogen reacts with oxygen in high temperature conditions to produce nitrogen oxides (NOx). Total NOx production is the sum of nitrogen monoxide NO and nitrogen dioxide NO2. The emissions of these gases are controlled through setting of emission limit values (ELVs) for power plants.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Continuous emissions monitoring for cement industry

    Process control and emissions monitoring in cement plants, can be a challenge due to the dusty and corrosive environment. OPSIS provides an accurate system that will operate with high performance and a minimum of maintenance.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Continuous emissions monitoring for mineral wool production

    Process control and emissions monitoring in a mineral wool plant is a challenge due to the presence of phenol and formaldehyde. To use an extractive system in this environment will demand a lot of maintenance. The OPSIS DOAS system is different and provides plants with an accurate analyser that will operate with a minimum of maintenance. The OPSIS DOAS system is based on a non-contact method using an optical measurement path that can operate across the duct.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Air pollution control for the coating industry

    Whether you are flow coating miniblinds, magnetic tape, aluminum cans, coils, wire or paper, Anguil`s 35 years of pollution control experience has provided unique insight into the wide variety of applications in the coating industry. Anguil`s experience leads directly to savings for our customers. Determining your solution begins by quantifying the problem with a thorough assessment of your emissions. Utilizing proven principles of design engineering, your system will evolve to incorporate air volume reduction strategies to reduce system size, meaning a reduction in both capital and operating costs. This can be achieved by recirculating the air in drying ovens or by cascading areas of lower VOC concentration to areas of higher VOC concentration.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Air pollution control for the chemical processing industry

    Anguil thermal and catalytic oxidizer systems are used on various applications throughout the chemical processing industry for emission abatement. Our experience includes applications on tank vents, amine tail gases, API separators, acid gases, inert streams and more. Regulatory Compliance Guaranteed, Seamless Process Integration, Efficient Destruction Technologies, Advanced System Controls.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Air pollution control for the electronics and semiconductor industry

    Anguil customers in the Semiconductor and Electronics industries include chip manufacturers, printed circuit board makers, LCD (Liquid Crystal Display) manufacturers and probimer operations. Each of these processes have unique emission control challenges that all require a custom engineered system designed around the given process parameters. With Anguil`s product breadth our customers are ensured that the proper technology will be chosen.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Air pollution control for the automotive industry

    Anguil`s engineering expertise has led to numerous successful air pollution control and emission control installations in the automotive manufacturing industry. From painting vehicles to engine test stations and tire manufacturing, we have supplied oxidizers and heat recovery systems to both tier 1 and tier 2 automotive plants.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Air pollution control for the remediation industry

    The remediation division of Anguil Environmental Systems (formerly known as Global Technologies) is focused on treating emissions and water contaminants extracted from below the earths` surface.  Formed shortly after the 1990 Clean Air Act targeted emissions associated with the extraction of polluted compounds from contaminated sites, Global subsurface remediation equipment has been successfully applied on contaminated sites in North and South America, Europe, Asia and Australia.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Air pollution control for the composite & carbon fiber industry

    Anguil is intimately familiar with emission capture, control and compliance hurdles that composite and carbon fiber producers face. We specifically address the needs of our carbon fiber customers with proprietary oxidizer designs for furnace and oven emissions. Our systems are recognized for energy efficient operation and destruction capabilities by the U.S. Federal Government at their Oak Ridge National Laboratories (ORNL). Anguil continues to help producers drive down energy consumption and emission output through our participation in The Beacon, an initiative at the forefront of green manufacturing practices for fiber production.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Gas detection analyzers for pollution control

    Government and environmental groups are forcing industries with medium to high VOC exhausts to reduce emissions by as much as 98%. Incineration using pollution control devices such as oxidizers and flare stacks is one way to bring the exhaust emissions in line with the regulations. Capturing and reusing solvent in a solvent recovery system is another way.

    By Control Instruments Corporation based in Fairfield, NEW JERSEY (USA).

  • Premium

    Air pollution control solution for the particulate matter

    Regulations around the globe are becoming more and more stringent for particulate emissions. Macrotek offers some of the most efficient wet and dry technologies to meet the latest EPA, EU, and MOE standards. Often, particulate collection is combined with acid gas removal. Our most advanced wet-dry system meets and exceeds the most stringent regulations for both hazardous gases and particulate.

    By Macrotek Inc. based in Markham, ONTARIO (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you