Only show results available in Virginia? Ok

emissions sampling Applications

  • Exhaust Gas Emissions

    Hiden gas analysis systems provide for high sensitivity, wide dynamic range, real-time analysis of almost any gas/vapour. Hiden’s application specific gas analysis systems are tailored to meet the specific application requirements, & include a range of special sampling, vacuum pumping & vacuum accessories. Hot zone sampling accessories are included for evolved gas analysis from furnaces, & thermo gravimetric analysers, TGA, for example. Thermal analysis methods are vital for catalysis characterization. For thermal analysis including TPD/TPO/TPR studies, Hiden gas analysis systems include enhanced pumping for hydrogen and special close coupled sampling to the TPD/TPO/TPR reactor for optimum thermal analysis response. In Biogas applications the simultaneous analysis of H2S, CO2, water vapour & CH4 in the PPM to 100% concentration range provides vital ininformation for process development and process monitoring...

    By Hiden Analytical based in Warrington, UNITED KINGDOM.

  • Premium

    Air sampling & monitoring systems for energy/utilities industry

    Finding efficient ways to generate, deliver and consume energy resources while reducing pollution is an ongoing quest for the Energy & Utility Industries. HI-Q has developed instrumentation geared toward monitoring emissions and the dispersal of pollutants from power plants and industrial facilities. HI-Q base-line & stack sampling equipment has been used in studies to identify and track the spread of pollutants around the globe.

    By HI-Q Environmental Products Company based in San Diego, CALIFORNIA (USA).

  • Air and particule sampling for the oil and gas industries

    Ormantine offers a wide range of products and services to meet the array of different needs that arise in the oil and gas industries. Volatile Organic Compounds (VOCs), benzene, and other compounds are released during drilling, hydraulic fracturing (fracking) and other extraction procedures. Monitor NOx emissions from heavy duty equipment, particulate matter, and ground level ozone, the formation of which is contributed to by VOCs from processing, transportation, and storage of oil and gas.

    By Ormantine USA Ltd., Inc. based in Palm Bay, FLORIDA (USA).

  • Premium

    Gas monitoring instruments and systems for engine emissions measurements

    The exhaust gas from combustion engines is a complex mixture of gases and particulate matter. The composition of the gas may change rapidly. Multicomponent analysis of exhaust gases can be performed with a Gasmet™ FTIR Gas Analyzer with a response time (T90) of one second. The winning combination is the result using of a small volume gas sample cell, a powerful sample pump and a fast detector with liquid nitrogen cooling. The analyzer, sampling system and computer can be assembled on a cart for use in a dynamometer laboratory, or the portable version can be used for roadside tests.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Cement & Lime Industry Emissions Analysis & Monitoring

    A key issue in the measurement of the products of combustion in Cement and Lime industries is the high levels of particulates. The Procal 2000 in situ analyser`s heated probe option is especially suited to this industry as it efficiently deals with variations in process temperature, keeping the probe above the sample dew point and safe from corrosive condensate.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Premium

    Monitoring solutions for the continuous emissions monitoring

    Multi-gas Stack Analyzers for Continuous Emissions Monitoring. FTIR and UVDOAS Analyzer Models available for Insitu Probe, Internal or External Cells, or Cross Stack Sample Acquisition.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Continuous emissions monitoring for CO2 capture

    The process control of a CO2 capture plant needs good and reliable detection of gas phase NH3 and CO2. Measuring NH3 is a challenge due to the corrosive environment and high concentrations of NH3. Several places in the process needs to be monitored and to transport the sample is difficult. A large dynamic range is needed as the NH3 concentration can vary between 15% volume and a few mg/m3.

    By Opsis AB based in Furulund, SWEDEN.

  • Continuous emissions monitoring for carbon capture and storage

    The process control of a CO2 capture plant needs good and reliable detection of gas phase NH3. Measuring NH3 is a challenge due to the corrosive environment and high concentrations of NH3. Several places in the process needs to be monitored and to transport the sample is difficult. A large dynamic range is needed as the NH3 concentration can vary between 15% volume and a few mg/m3. 

    By Enviro Technology Services plc based in Stroud, UNITED KINGDOM.

  • Premium

    Measurement of hydrogen sulfide & carbon disulfide in air for continous emission monitoring

    The Series 8900 Hydrogen Sulfide and Carbon Disulfide Analyzer provides direct measurement of H2S and CS2 in ambient air. This instrument is utilized for continuous emission monitoring. The Series 8900 H2S and CS2 Analyzer employs a Photoionization detector (PID) as the sensing element. A dual column configuration with timed backflush to vent is used to strip off moisture and heavier hydrocarbons. A pre-cut column is used in series with the analytical column. At sample injection a fixed volume of sample is carried to the pre-cut column. Backflush is timed so that only the H2S, CS2, and other similar components are eluted to the analytical column. Contaminants on the pre-cut column are backflushed to vent. H2S and CS2 are separated from potentially interfering components on the analytical column and elute to the detector for analysis.

    By MOCON, Inc. - Baseline based in Lyons, COLORADO (USA).

  • Premium

    Measurement solution for CFC analyser

    CFCs are used in the manufacture of insecticides and herbicides and the environmental impact of their use must be well controlled. The treatment of CFC emissions to reduce the emissions in the intermediary steps of production needs to be monitored with 100% efficiency. Protea’s portable CFC analysers and continuous CFC monitoring systems can be configured with various sample inlets and analytical modelling to enable multi-samples to be measured on the one system. This means that both inlet and outlet to abatement systems can be monitored using the one analyser.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Perimeter Ambient Air Monitoring

    Cerex Multi-Gas Open Path Analyzers are available in both FTIR and UVDOAS technologies to meet specific requirements for perimeter ambient air quality monitoring, leak detection, fugitive emissions monitoring and ambient air quality monitoring. Cerex multi-gas analyzers offer significant advantages over single gas analyzer arrays, electro-chemical sensor arrays and time integrated air sampling hardware

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Determination of TOC in stack

    PROBLEM: The industrial chimney's emissions of Volatile Organic Compounds (VOCs) are becoming issues of global importance and to have an accurate knowledge about how to test VOC turns into a strategic issue. VOC emissions are quantified and monitored according to standard EN 12619, using FID analyser which uses hydrogen and other reference gases in pressurized cylinder. Operators must then approach the sampling point, often placed several meters from the ground, climbing chimneys of industrial settlements with instruments and cylinders. Is it possible making this job easier and safer? SOLUTION: Using the Polaris FID analyser produced by Pollution Srl, Italy, it is possible to carry out the VOCs monitoring according to EN 12619 without lifting accessories and heavy weights typically involved with FID analyser. Polaris FID analyser complies with this standard regulation but what is really a breakthrough and cutting-edge, is the unmatched portability and the next generation technology

    By Pollution Srl based in Budrio, ITALY.

  • Premium

    Gas Detection Solutions for Aluminium

    Primary aluminium smelting generates large amounts of hydrogen fluoride gas (HF). Worker safety and ambient air quality concerns require that HF be monitored at several locations in smelters. Traditionally, a variety of chemical sampling methods have been used for HF monitoring in and around smelters. However, these methods are labour intensive and require ongoing maintenance and consumables. During the past decade, laser based HF analyzers have been replacing the traditional methods. Laser analyzers are compact, robust and reliable and provide accurate HF data. Fast response times that enable easy correlation of high HF emissions with work practices.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • NOx analyzers for Automotive Mobile Sources

    NOx analyzers for transportation industry exhaust emissions. Options include a heated sample inlet for hot, moist engine exhaust, and AK protocol. View Automotive/Mobile Source Products

    By ECO PHYSICS INC. based in Ann Arbor, MICHIGAN (USA).

  • Premium

    Gas Detection Solutions for GHG Monitoring

    Most sources of fugitive emissions are from multiple points rather than single point sources. So, open path area or perimeter monitoring provides more meaningful fugitive emissions data than an array of point sensors or a program of grab sampling. Point measurements may underestimate emissions because of missing locations with high gas concentrations, or conversely overestimate because they are located in areas of high concentrations. Grab sampling programs typically check only a small percentage of potential leak locations and extrapolate results to an entire facility. Wide margins of uncertainty are associated with such extrapolations. Open path monitoring provides continuously updated, real-time, integrated emissions across a facility boundary.This provides a complete picture of the fugitive emissions across that boundary,enabling identification of specific operations and times that give rise to higher emissions, and so enabling these emissions to be properly managed and controlled.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Independent particle characterization services for environmental industries

    Particle size, particle concentration and other physical characterization analyses are critical to many environmental applications. Regulatory agencies in the environmental sphere demand strict compliance to standards and discharge regulations. Physical testing of samples for parameters such as particle size and concentration can give insight to the process control engineer on how effective and compliant a discharge handling system is operating. Particulate loading from both air emissions and waste water discharge are monitored in many industry sectors and PTL testing provides valuable supporting data in this monitoring process.

    By Particle Technology Labs based in Downers Grove, ILLINOIS (USA).

  • Air monitoring for laboratories

    Many of the air quality analyses can be performed with standard laboratory consumables, such as traditional filter papers. However, some analyses require materials with specific features, for example filters with low metal levels.

    Common air monitoring applications include:

    • Air quality testing of ambient environment and emissions. Includes particulate monitoring methods such as PM2.5 and PM10, and chemical analysis such as heavy metals determination.
    • Asbestos sampling and analysis

    By GE Healthcare UK Limited based in Little Chalfont, UNITED KINGDOM.

  • EPR waste minimisation monitoring for wastewater treatment industry

    The EPR regulations have replaced the IPPC regulations and are effective from May 2009 for qualifying companies within the industrial sector and October 2009 within the water sector. They will progressively require industry to minimise waste, reduce product loss and implement improved process control. The legislation will require the operator to self monitor processes and discharges, to demonstrate effective control with particular emphasis on EPR compliance and prevention. The regulating Agency will operate a point scoring system to assess operators under the OMA-3 program and this will be used to identify how well a company is managing their processes and possibly identify areas for improvement. The Environmental Permitting Regulations require industry to install instrumentation (MCERTS approved where available) to report water quality. EPR compliance monitoring may include automatic water sampling, flow measurement, pH, turbidity and TOC water analysis. Industry will need to identify point of source emissions, take steps to correct inefficient control and alarm unacceptable process deviations. Although the legislation focuses on environmental improvement, good housing keeping also makes a lot of sense. Optimisation of process control minimises waste, reduces treatment costs and ultimately saves money.

    By Pollution & Process Monitoring Ltd based in Sevenoaks, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you