Only show results available in Virginia? Ok

emissions standard Applications

  • Emissions testing for engines

    Rich-burn engine exhaust, when uncontrolled, can have wide concentration ranges and both CO and NOX can fluctuate significantly. The on-board CO dilution system will automatically set-up for optimum testing, perfect for a rich burn engine. Lean-burn engines have different exhaust characteristics, but NO2 can make up a significant portion of the total NOX measurement. The 350 measures both NO and NO2 for proper lean-burn engine set-up. Due to high concentration, replaceable interference filters keep the sensors...

    By Testo, Inc. based in Sparta, NEW JERSEY (USA).

  • Premium

    Emission Monitoring for the Metal Industry

    The metal industry comprises a large variety of different branches, beginning with metal winning and recovery, metallurgy, metalworking and extending to manufacture of machines and devices for which metal finishing and electroplating are indispensable process steps for quality standards. These industries face the difficulties of improved process control and lower environmental stress. AppliTek implements on-line monitoring in specific processes of the metal industry to increase process efficiency and...

    By AppliTek NV based in Nazareth, BELGIUM.

  • Premium

    Emissions Monitoring for Cement Plants

    Opsis provides state-of-the-art monitoring equipment, fully meeting the high standards of monitoring performance and reliability that the cement industry requires. The Opsis in situ systems are designed to withstand environments with high particulate levels and high temperatures.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    EDXRF spectrometers for marine emission control

    The IMO (International Maritime Organization) continuously sets new standards in order to minimize and control the harmful polluting exhausts from vessel engines. IMO is the World’s largest maritime organization with over 170 member states and acts as a regulatory agency for the international maritime industry.

    By Xenemetrix Ltd. based in Migdal Haemek, ISRAEL.

  • Marine And Offshore Emissions Monitoring & Analysis

    The need to demonstrate environmental responsibility is key for today’s marine and offshore industries. Fuels and exhaust gas emissions are subject to international, regional and national controls and Charterers, as well as the public, demand high standards of performance and reliability.

    By Procal - Parker Hannifin Corp based in Peterborough, UNITED KINGDOM.

  • Thermal structures for emissions / after treatments industry

    Every year emissions standards become more stringent. More stringent standards often require elevated exhaust temperatures. Thermal Structures products have been developed specifically to deal with these increased temperatures. By isolating and managing elevated exhaust temperatures, Thermal Structures enables operators to meet more stringent emissions standards without risking damage to sensitive components. Our products help to make environmental resposibility an easy choice.

    By Thermal Structures, Inc. based in Corona, CALIFORNIA (USA).

  • Premium

    Laboratory Weighing - Filter Weighing

    Traffic means mobility and air emissions. Thanks to economical advantages, diesel engine becomes more and more popular, but particle emission is strictly restricted by regulations. Determining the weight of particulate matter (PM) is a key task in the automotive industry and one which is likely to become even more important as emissions standards become stricter. To allow fast and easy measurement of particulate matter at any time, METTLER TOLEDO has developed new filter weighing solutions.

    By Mettler - Toledo Int. Inc based in Greifensee, SWITZERLAND.

  • Premium

    Air pollution control for the pharmaceutical industry

    From pill coating and mixing operations to Ethylene Oxide (ETO) sterilization, Anguil has had great success solving a wide range of emission control applications in the pharmaceutical industry. As companies struggle to comply with the EPA`s MACT (Maximum Achievable Control Technology) standards or international regulations, it is comforting to know that Anguil thoroughly understands your process. Over three decades...

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Air pollution control for the printing, laminating & converting industry

    Achieving cost effective local regulatory compliance in the printing and converting industry requires a complete understanding of both regulatory standards and the printing process. Through experience, Anguil has developed unparalleled expertise in meeting your unique requirements. We understand the effects of water versus solvent-based inks on the line, elimination of odors and toxic fumes from...

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Hazardous waste treatment solutions for oil and gas industry

    There are a wide amount of applications for our VacuDry® process within the oil and gas industry. A large variety of wastes and by-products that are generated in the oil & gas production chain can be treated effectively and sustainably. In past decades, numerous thermal desorption processes have been implemented worldwide, using a variety of heating chamber designs to separate hydrocarbons from the mineral solids. Such standard TDUs work under atmospheric pressure which can lead to safety...

    By econ industries services GmbH based in Starnberg, GERMANY.

  • Premium

    Gas monitoring instruments and systems for stack testing

    Several EU directives and national laws in European countries set requirements for continuous monitoring of flue gas emissions at power plants. Further requirements are set on the quality assurance of the installed measurement systems at the plants. The relevant standard in this regard is EN 14181:2004, the quality assurance of automated measuring systems. The standard dictates how to determine that the measurement systems installed for continuous emissions monitoring at a plant operate according to the...

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Industrial air pollution control for the electronics and electrical industry

    The world`s appetite for electronic devices - from simple household appliances to sophisticated computers - has led to rapid growth of both these industries. Typically for the electronics industry, there are large waste gas streams (up to 400,000 Nm³/h) with relatively low concentrations of different solvents. The waste gases mainly occur in coating, cleaning and etching processes during the production of semiconductors, CDs/DVDs, Blue-ray discs,...

  • Premium

    Determination of TOC in stack

    PROBLEM: The industrial chimney's emissions of Volatile Organic Compounds (VOCs) are becoming issues of global importance and to have an accurate knowledge about how to test VOC turns into a strategic issue. VOC emissions are quantified and monitored according to standard EN 12619, using FID analyser which uses hydrogen and other reference gases in pressurized cylinder. Operators must then approach the sampling point, often placed several meters from the ground, climbing chimneys of industrial settlements with...

    By Pollution Analytical Equipment based in Budrio (Bologna), ITALY.

  • Premium

    Anaerobic water purification systems for municipalities

    Tighter discharge consents, reduced energy consumption, reduction of CO2 emission, advanced nutrient removal from effluent, increased capacities and decentralized treatment are the modern trends that waterboards and municipalities are facing. In order to meet new standards, municipalities are looking for specialized solutions.

    By Paques B.V. based in EL Balk, NETHERLANDS.

  • Premium

    Air monitoring for laboratories

    Many of the air quality analyses can be performed with standard laboratory consumables, such as traditional filter papers. However, some analyses require materials with specific features, for example filters with low metal levels.

    Common air monitoring applications include:

    • Air quality testing of ambient environment and emissions. Includes particulate monitoring methods such as PM2.5 and PM10, and chemical analysis such as heavy metals determination.
    • Asbestos sampling and analysis

    By GE Healthcare Life Sciences based in Marlborough, MASSACHUSETTS (USA).

  • Premium

    Sound level meters & Noise dosimeters for Vehicle noise measurements industry

    The noise from vehicles such as cars, buses and trucks is wide spread with many people being affected by these noise sources in their daily lives. All modern vehicles will be designed to meet strict safety and emissions standards as well as noise output levels. All vehicles sold in the EU must comply with a range of noise directives to ensure that they meet these specified noise levels when they are sold and many countries enforce regular checks over the life of the vehicle. Motor Sport noise is a often a...

    By Cirrus Research plc based in Hunmanby, UNITED KINGDOM.

  • Stack Testing for the Aluminum Industry

    ALUMINUM INDUSTRY: Performed a range of test measurements required by the promulgation of the Secondary Aluminum MACT standards. Testing included measurements of Hazardous Air Pollutants for establishing Area vs. Major Source Determinations, as well as dioxin/furan compounds associated with chlorine emissions from fluxing operations.

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

  • The Environmental Measurement Laboratory (EML)

    PP “Tehnologia O” has an Environmental Measurement Laboratory (EML) that allows to carry out instrumental measurements of emissions of pollutants into the air. EML have earned certification under services in state control of adherence to standards, norms, rules and state metrological control from SOE “Vinnytsya Center for Standardization, Metrology and Certification” (SOE “Vinnytsyastandartmetrologiya”) (certificate No. ПУ-0070/15 valid till 03 July 2018).

    By PP `Tehnologia O` based in Vinnytsia, UKRAINE.

  • AIR PURIFICATION

    Citto Activated Carbon 'Air Series' offers a range of standard, impregnated, and specialized activated carbon products for a wide spectrum of air purification applications. The dynamic product array of the Citto Activated Carbon 'Air Series' is developed to meet stringent emission control regulations as well as safety standards for emerging respiratory technologies effectively removing nuisance odors, volatile organics, and hazardous chemicals from air and gas streams.

    By Citto Corporation based in TORONTO, ONTARIO (CANADA).

  • Air pollution control solution for the particulate matter

    Regulations around the globe are becoming more and more stringent for particulate emissions. Macrotek offers some of the most efficient wet and dry technologies to meet the latest EPA, EU, and MOE standards. Often, particulate collection is combined with acid gas removal. Our most advanced wet-dry system meets and exceeds the most stringent regulations for both hazardous gases and particulate.

    By Macrotek Inc. based in Markham, ONTARIO (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you