Only show results available in Virginia? Ok

energy measurement system Applications

  • Measurement and control systems for the heat & steam technology

    Reduction of perating costs: The increased energy costs over the last years have made investments towards heat recovery solutions not only cost effective but profitable. With the support and input of our employees and our technical know how, are improvements and solutions concerning heat recovery become feasible.

    By IGEMA GmbH based in Münster, GERMANY.

  • Measurement and control systems for the Indicating the level - mechanically

    Depending on the regulations, a steam boiler must be equipped with one or more direct and/ or indirect level gauges. With direct level gauges, the liquid level can be seen directly through a glass or mica window. The use of a transparent level gauge with background illumination gives operating staff a clear separation between the water and steam zones even when viewed at a relatively long distance. Bicolour level gauges (black and white or green and red) are very suitable for camera transmission to the measuring station because of their special design and the intense LED illumination. With indirect level gauges, the water level is transmitted by a magnetic system to a display panel on the outside of a pipe.

    By IGEMA GmbH based in Münster, GERMANY.

  • Measurement and control systems for the Boiler water monitoring

    In ongoing operation, the substances suspended in the boiler water are concentrated. In order to avoid the negative consequences (foaming, deposits) of excessive salt content in the boiler water, specified limit values must not be exceeded. With the aid of a desalination control valve, boiler water with concentrated content is constantly removed and replaced with clean water. If the limit values are exceeded, the conductivity limitation ensures prompt switching off of the burner(s). Foreign substances that have sunk to the bottom of the boiler are removed by briefly opening a drainage valve.

    By IGEMA GmbH based in Münster, GERMANY.

  • Measurement and control systems for the controlling the level - electronically

    Discontinuous control is used mainly in smaller steam boilers with low output since the temperature fluctuations in the boiler are fairly great as a result of irregular refilling with water. Continuous control, on the other hand, permits still more economical steam generation with high quality.

    By IGEMA GmbH based in Münster, GERMANY.

  • Water Monitoring and Flow Measurement Systems for Water Power

    Hydro power contributes to supplying approximately 3,5 per cent of electric energy generated worldwide. Its share in power generation from renewable resources lies at 18 per cent and will continue to grow as resources of fossil fuels are depleted. Hydro electric performance depends essentially on the usable altitude difference between upper and lower reservoir, and hence the resulting water flow. In order to use the “fuel” water in an optimal way, the flow velocity has to be monitored without any interruptions. Ultrasonic flow meters, flow sensors and clamp-on flow meters (OR clamp-on technology) are ideal for accurate flow metering and flow monitoring.

    By HydroVision GmbH based in Kaufbeuren, GERMANY.

  • Weather Monitoring Systems for wind energy sector

    Wind power is now the world`s fastest growing alternative energy source and has also become one of the most rapidly expanding industries. For over 40 years, Climatronics has been a leading developer and manufacturer of wind measurement sensor technology to the growing wind power generation market. We offer precision weather sensors for wind energy applications such as wind resource assessment, wind turbine generator control, and wind farm performance management.

    By Climatronics Corporation based in Bohemia, NEW YORK (USA).

  • Weather Monitoring Systems for industrial and utility sector

    The weather can have a major impact on many industrial processes and operations, both from an operational efficiency and/or safety standpoint. For example, real-time information about ambient atmospheric conditions provides the necessary input data required to make the proper decisions during an industrial emergency involving any type of hazardous material. Depending on the plant type, size and age, the federal Environmental Protection Agency (EPA), as well as municipal and state environmental regulatory organizations, also require that a number of basic meteorological variables are measured and recorded on site to ensure compliance with environmental regulations.

    By Climatronics Corporation based in Bohemia, NEW YORK (USA).

  • Wind Energy Meteorology

    As the world addresses the challenges of global warming green energy production and in particular wind energy generation has increased significantly. Biral can provide sensors for the control of aviation obstacle light intensity, wind speed measurement and site assessment. The Deutscher Wetterdienst (German Meteorological Service – DWD) has certified the VPF-710, SWS-100 and SWS-200 sensors as suitable for use in visibility controlled wind turbine obstruction light systems.

    By Biral - Bristol Industrial & Research Associates Ltd based in Portishead, UNITED KINGDOM.

  • Ammonit Wind Ressource Assessment Systems

    Prior to setting up a wind farm, the local wind conditions have to be measured for site assessment. The construction of a profitable wind farm demand the most accurate and reliable wind measurement technology. The installed equipment has to perform as precisely as possible as the data quality is essential for designing a reliable and economical wind farm. A small discrepancy in the evaluation of wind speed data drastically multiplies the discrepancy of the calculated wind power. Wind resource assessment systems offered by Ammonit meet the highest standards of quality and are designed for the local site conditions with regard to sensor performance, communication system and power supply.

    By Ammonit Measurement GmbH based in Berlin, GERMANY.

  • Ammonit Wind Farm Monitoring Systems (SCADA)

    Once the wind farm is set up and running, its best performance has to be ensured. To do so, it is essential to monitor and check its operation. Meteo-40 can easily be integrated in SCADA (Supervisory Control and Data Acquisition) systems to provide reliable comparative meteorological data. Considering the measurement data recorded by Meteo-40, for example, predictions about the annual energy production of the wind farm can be verified. Meteo-40 records measurement data, which is used by wind farm operators and investors, as well as for forecasting reasons. With its configurable Modbus Register Map Meteo-40 is designed for operation in most existing SCADA systems. The necessary parameters are configured via the user-friendly Meteo-40 web interface.

    By Ammonit Measurement GmbH based in Berlin, GERMANY.

  • Premium

    Biogas Monitoring for the Renewable Energy Industry

    AppliTek`s solutions in this field concentrate on the process efficiency of anaerobic digesters. Many existing digesters give unnecessary problems, which arise due to inadequacies in the process or process control system. AppliTek has developed a unique instrument to measure and control the key processes in the anaerobic fermentation. Compact gas analyzers with proprietary technology can be implemented to check the biogas yield.

    Parameters: Volatile Fatty Acids - Alkalinity - pH - Bicarbonate

    Gas parameters: CH4 - CO2 - O2 - H2S

    By AppliTek NV based in Nazareth, BELGIUM.

  • Premium

    Water treatment for power plants

    The process of electricity generation from fossil fuels such as coal, oil and natural gas is water-intensive. Between 40-50% of all water abstracted and used in developed countries is used in the generation of electricity. Thus, a reliable, abundant and predictable source of raw water supply to a power plant is a critical factor in site selection. Water supplies are required to provide various process waters for the following essential main purposes such as make-up water, cooling water for steam turbine condensers, and auxiliary plant cooling water.

    The primary application of modern water treatment technology is to maintain the integrity and performance of the power plant. Critical plant applications have water purity or conditioning requirements that must be adhered to for safe, reliable and efficient power generation.

    Experience has shown that integration of water technology treatments with power plant design can be very important in reducing operational problems and component failures 

    At power plant worldwide there are increasing limitations on water availability and environmental restrictions on discharges. This is expected to promote measures for water conservation and to have an increasing influence on water treatment decisions. At power plant, the recycling of internal wastewater streams can extend from the recovery of individual high-quality waste streams, which can be reused either directly or after only limited treatment, through to the development of fully integrated water/wastewater treatment systems for zero liquid discharge. However, the application of reuse schemes requires site-specific assessment, as not all waters may be viable options for recovery.

  • Premium

    Emissions monitoring for waste incineration

    Process control and emission monitoring in a waste to energy plant is a challenge. A large number of gaseous components need to be measured with high accuracy. Almost 100% uptime is required and the monitoring system needs to be easy to maintain and fast to calibrate.

    By Opsis AB based in Furulund, SWEDEN.

  • Meteo and Wind Monitoring Wind Energy Sector

    The Renewable Energy market is expanding rapidly to reduce the dependency on traditionial energy sources and to reduce CO2 emissions in the future. Mierij Meteo offers sensors and system for many applications in the Renewable Energy market. Mierij Meteo supplies wind sensors for wind turbine control, Automatic Weathers Station for forecasting and robust and accurate sensors for research and power curve measurements (MET masts). By using Mierij Meteo sensors and systems you will ensure optimal of your wind turbines. With our MET masts you will get the most reliable data to help make your investment in renewable energy become more profitable.

    By Mierij Meteo b.v based in De Bilt, NETHERLANDS.

  • Ammonit Solar Resource Assessment Systems

    In order to assure well-founded decisions in designing profitable solar power plants, the solar irradiance should be measured in the assessment phase. Irradiation is a crucial parameter for site selection and plant design and economics of plant. There are many different ways and technologies to measure the irradiance phenomena that influences the power generation of a future solar power plant. Ammonit’s solutions are designed to meet the latest standards with regard to accuracy and affordability of the measurement.

    By Ammonit Measurement GmbH based in Berlin, GERMANY.

  • Emissions testing for engines

    Rich-burn engine exhaust, when uncontrolled, can have wide concentration ranges and both CO and NOX can fluctuate significantly. The on-board CO dilution system will automatically set-up for optimum testing, perfect for a rich burn engine. Lean-burn engines have different exhaust characteristics, but NO2 can make up a significant portion of the total NOX measurement. The 350 measures both NO and NO2 for proper lean-burn engine set-up. Due to high concentration, replaceable interference filters keep the sensors stable and your readings accurate. High exhaust pressures and heavy particulate loading are easily controlled with the special pressure relief valve (standard) on the engine probe configuration.

    By Testo Inc. based in Sparta, NEW JERSEY (USA).

  • Ammonit Wind Resource Assessment in Cold Climates

    For wind resource assessment campaigns in regions with long and cold winters, special measurement systems have to be designed. The challenges of cold climate regions should never be underestimated. Particularly icing is a problem. The met mast construction and the installed sensors have to be chosen carefully. The instruments have to be properly heated by a reliable power system. With our long-term experience in wind measurement and our local installation partners we can offer complete measurement systems robust enough for harsh and cold climates. Ammonit offers standard heating systems as well as individual heating solutions, which combine several power sources suitable for the site.

    By Ammonit Measurement GmbH based in Berlin, GERMANY.

  • Hukseflux Pyranometers

    Hukseflux offers a complete range of instruments for applications in solar energy / PV system performance monitoring. Please visit our website to discover the possibilities and solutions for your industry. Whatever your application is, Hukseflux offers the highest measurement accuracy in every pyranometer class. The overview below, of SR20 pyranometer features and benefits, gives you some of the reasons why the best pyranometers are made by Hukseflux. Click the image to visit our website.

    By Hukseflux Thermal Sensors B.V. based in Delft, NETHERLANDS.

  • Premium

    SF6 Leak Detection

    Monitoring Sulfur Hexafluoride (SF6) in the Power Utility Industry. Monitoring Sulfur Hexafluoride in the Power Utility Industry The SF6 Leak Detector 3434i from LumaSense offers an unmatched combination of performance and convenience. Based on the company’s Photoacoustic Spectroscopy (PAS) technology, the system offers highly accurate, reliable and stable quantitative gas analysis and detection. The growing environmental requirements and pressures regarding the use of SF6 make LumaSense’s system a coveted tool designed for everyday use. The system is able to measure the total concentration of the SF6 gas in an enclosed area, where the switchgear (or other SF6 filled equipment) is tested. Although only the total amount leaked is required by today’s standards, it is also advantageous to be able to pin point the leaks. This makes it easier to improve the integrity of the equipment. The SF6 Leak Detector system meets all of requirements for confined area such as substation Monitoring.

    By LumaSense Technologies, Inc. based in Santa Clara, CALIFORNIA (USA).

  • Stack Testing for Power Generation Plants

    POWER GENERATION INDUSTRY: Conducted detailed measurements of volumetric flow, oxygen, and carbon dioxide levels in huge main ducts in the Economizer Outlet, Air Heater Inlet, and Exhaust Stack locations in order to evaluate overall plant and control system performance

    By AirSource Technologies, Inc. based in Shawnee, KANSAS (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you