Flue-gas analyzers are designed to be rugged and accurate at the same time. They are used by the HVAC industry, energy industry, process control, glass industry, food industry, universities and analysis is required.
Weathering of materials is most often an irreversible process affecting the cosmetic properties or strength of materials. This aging process is mainly driven by UV radiation, Heat and reactive elements in the atmosphere, for example chemical contamination. The plastic fabric of the product can dry and therefore weakened. The solar load can overheat the products and change material properties irreversibly. A common method to test the deterioration of materials is to expose materials to sun light and environment....
Researchers and Engineers utilize HI-Q air sampling equipment and systems for analyzing and investigating environments around the world. Data collected by HI-Q air sampling systems have provided critical information in the identification and prevention of pollution. HI-Q offers a line of high volume (TSP-Type) air sampling systems for data collection in perimeter monitoring & industrial emissions monitoring applications.
The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M.
Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.
Mercury, being widespread in environment, has toxic effect on a human organism even at a low concentration. Therefore, quantitativ e determination of mercury in vari ous environments is one of the most important environmental monitoring problems. The use of a mercury analyzer RA-915M/RA-915+/RA- 915Light with Zeeman background correction provides di rect real-time continuous determination of mercury in air from 0.5 ng/m 3 within the overall possible range of me rcury concentration in ambient air.
Levels of of hydrogen in the gas vent of the HCl burner can be measured by means of AppliTek’s thermal conductivity analyzer system. The analyzer system is suited for use in hazardous environments and meets ATEX or NEC500 compliance standards.
Levels of of hydrogen in the hydrogen feed of the HCl burner are reliably measured and controlled by means of AppliTek’s thermal conductivity analyzer system. The analyzer system is suited for use in hazardous environments and meets ATEX or NEC500 compliance standards.
With over 15 years of experience in the measurement of volatile organic compounds (VOC), Environment SA announces the VOC72M, a new generation analyzer for the measurement of BTEX compounds by gas chromatography with photo-ionization detector (PID). The VOC72M can handle up to 40 compounds and eight configurations for analysis. This compact and fully automated analyzer with wide voltage range specifications (90-240V) provides equivalent performance to the laboratory chromatographs and is particularly suited to...
Hydrogen chloride (HCl) is a colorless, sometimes slightly yellow, gas. It is an undesired environmental component that may be damaging to workers and the surroundings. Exposure limits have thus been established by industries to make sure that the workers operate in a safe environment. HCl monitoring is especially required for incinerators, coal-fired power plants, aluminum recycling and cement plants. Unisearch offers a reliable and easy-to-use HCl analyzer – the TDLAS-based LasIR system. Studies have...
Environics® Ambient Monitor Calibrator with Ozone Generators facilitate dynamic calibration of ambient air analyzers. These instruments automatically perform zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, O3, hydrocarbons and other gases of interest. All ozone generators are factory calibrated using a NIST traceable ozone standard. The Series 6100, Series 6103 and Series 9100 all meet or exceed U.S. Environmental Protection Agency requirements.
A safe laboratory environment requires an
effective method for clearing toxic material from fume hoods. Since all handling of toxic
materials is completed in these hoods, it is
critical to have a procedure to evaluate their
operation to assure adequate protection for
laboratory workers. The InfraRan Specific
Vapor Analyzer, factory calibrated for SF6, is an ideal instrument for measuring fume hood
efficiency in accordance with ASHRAE and
other standards. Manufacturers identify the flow
dynamics (factors that...