Only show results in Virginia? Ok

environmental monitoring system Applications

  • Chromatography systems for environmental monitoring

    With the growth of contamination generated from agricultural and industrial production, it causes a threat to the enviroment including drinking water, atmosphere and soil. The chemists have always seeked out the effective analytical methods to detect and identify chemical contaminants. Dikma provides innovative products and application solutions according to government regulations and industry standards, for air and water quality monitoring, gas detection.

    By Dikma Technologies Inc. based in Lake Forest, CALIFORNIA (USA).

  • Meteorological systems for environmental monitoring

    Climatronics has supplied meteorological systems for environmental monitoring and regulatory compliance for over 35 years. Our accurate, responsive, yet rugged sensors, coupled with high-power data loggers, provide users with the ability to make measurements on multi-level towers, multiple tower networks, and single sites, which comply with EPA, NRC, and international regulatory requirements.

    By Climatronics Corporation based in Bohemia, NEW YORK (USA).

  • Environmental Monitoring

    Environmental monitoring is becoming more important every day in local, national and international policies, showing the environmental awareness demanded by society.

    This fact gives rise to an increase in the amount of legislation that obliges companies to law enforcement. Thus, the necessity of making more pollutants controls means high analysis expenses to the companies, which need to subcontract this service.

    Although applications in this area advance, there is still a clear demand to get new portable and versatile analysis systems for many different application fields such as pollution in environmental or waste waters, monitoring nutrients in agricultural or horticultural water as well as general process control in chemistry industry. Because of the number of enviromental analysis required, there is a need for screening and monitoring measurements of these compounds at contaminated areas.

    Traditional monitoring techniques are typically based on laboratory analysis of field-collected samples that require considerable effort and expense, and the sample may change before analysis. Moreover, the equipment currently available is too large and expensive and it cannot be made portable.Alternatively, microfluidic and electrochemical sensor technologies can contribute to the development of new portable monitoring systems, complementing standard analytical methods for different environmental monitoring applications.In this way, the decentralization and integration of all those typical analyses is the paramount importance in order to reduce cost, simplify the analytical process and make more accessible these technologies to end-users. The development of portable, robust, and accurate Lab-on-a-Chip systems to monitor priority compounds such as contaminants, explosives, chemical warfare agents, inorganic and organic ions is a demand of modern society. Portability allows analyses to be carried out outside of the laboratory, minimizing the risk of contaminating the sample and leading to a faster response time at a lower cost.

    Thus, MicruX solutions and technologies open the gate to develop portable and esay-handly Lab-on-a-Chip devices in order to improve pollutants in-situ analysis in a very economic and efficient way.

    By MicruX Technologies based in Oviedo, SPAIN.

  • Temperature monitoring in a rotary kiln

    Taking measurements on rotating equipment, such as a kiln or rotary table, usually requires a complex and expensive system of cabling. Even taking precautions and using specialized equipment doesn’t eliminate cable tangles and breaks. The SureCross Wireless Network eliminates complexities associated with data acquisition from rotating and moving machinery such as a rotating kilns in cement or composting industry. Crucial temperature data is acquired using a thermocouple and transmitted from the FlexPowered SureCross Nodes to a remote Gateway in the plant’s control center.

    By Banner Engineering Corp. based in Diegem, BELGIUM.

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Laser detection solutions for environmental monitoring

    LDI laser remote sensing technology provides users with the tools to conduct broad and accurate environmental surveys of both water and ground in stressed environmental zones, which makes our products especially suitable for oil spill response operations. The technology is based on the Laser Induced Fluorescence (LIF) and realized by the Fluorescent Lidar Systems – FLS (LiDAR – Light Detection And Ranging).

    By Laser Diagnostic Instruments AS based in Tallinn, ESTONIA.

  • Premium

    PTR-TOFMS systems for Flux Measurement of BVOCs

    The ultra-fast analysis capabilities of IONICON PTR-TOF instruments are essential for eddy covariance flux measurements, allowing to study deposition and emission rates of biogenic volatile organic compounds (BVOCs).

    By Ionicon Analytik Ges.m.b.H. based in Innsbruck, AUSTRIA.

  • Fugitive emissions monitoring on industrial sites

    The real-time monitoring of odorous gases or more classical pollutants emitted by industrial sites (wastewater treatment plants, refineries, landfills, etc.) appears nowadays as a requirement, in order to optimize the site process and operations, or communicate towards the neighborhoods and local public bodies. While emissions can be measured directly at the source (in the stack, exhaust, etc.), ambient air measurement all around the sites provides a better accuracy and anticipate pollution episodes. This is why Cairpol developed around its Cairsens sensors a concept of smart and autonomous stations: Cairnet. Without any maintenance nor calibration, Cairnet is a completely autonomous system energy-wised, with user friendly and efficient interface, accessible from any internet-connected device.

    By Cairpol based in La Roche Blanche, FRANCE.

  • Meteorological Monitoring

    FTS designs complete, turn-key systems for a variety of environmental monitoring applications. Our systems are based upon the Axiom datalogger—a key technology that deliver rugged reliability in any environment, simplicity of operation, low maintenance costs, and extremely accurate data.

    By FTS based in Victoria, BRITISH COLUMBIA (CANADA).

  • Sediment Pollution Instruments

    Our SediMeter instruments are designed with sediment pollution monitoring in mind. They form part of a system with network and software components designed specifically to be the best possible sediment pollution monitoring system.

    By Lindorm, Inc. based in Medley, FLORIDA (USA).

  • Continuous Monitoring of Nitrates and Other Water Quality Parameters

    Nitrate is one of the most important parameters in assessing surface and ground water quality. Nitrates are naturally present in surface and ground waters in low concentrations, but are harmful to humans and livestock and cause aquatic ecosystem degradation in high concentrations. Nitrates enter the environment as human-induced pollution from a variety of sources, but the largest source is from agricultural fertilizer runoff . Other sources include wastewater treatment discharge, septic systems, and from pet waste. Nitrate is highly soluble in water and therefore readily leaches into water sources, whereas other human associated pollutants, such as phosphates and ammonia, are not transported as easily. This ability to be quickly transported into ground and natural waters such as drinking water wells, aquifers, reservoirs, lakes, and streams, coupled with its health and environmental implications make nitrate pollution and monitoring of major concern.

    By Hanna Instruments, Inc based in Woonsocket, RHODE ISLAND (USA).

  • Premium

    Ambient air quality monitoring solutions for street-level monitoring

    To measure the air quality in a city is a challenge. A large number of gaseous components need to be measured with high accuracy. The monitoring site needs to be representative for the city and the system has to be easy to maintain and calibrate. The OPSIS open-path monitoring systems provide a flexible solution, giving the average concentration for an area. A single OPSIS system can measure all relevant gaseous components set by the authorities, such as NO, NO2, SO2, O3, BTX, NH3.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Ambient air quality monitoring solutions for fence-line monitoring

    The OPSIS open-path monitoring system is an excellent tool for monitoring the air quality, fugitive emissions and gas leaks at industrial sites. By arranging monitoring paths strategically at locations outside the borderline of an industrial area, fugitive emissions and gas leaks will effectively be detected. By combining the measured gas data with meteorological parameters information such as where the pollution sources are located and the strength of the emissions can be calculated, using the EnviMan software.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Gas analysis & monitoring system for emission monitoring

    From the environmental point of view, an issue is any solid, liquid or gaseous substance introduced into the atmosphere that can cause air pollution. Given the wide variety of substances present in the atmosphere, have been proposed several methods of classification: Primary pollutants can be of gaseous or particulate.

    By ETG Risorse e Tecnologia based in Montiglio, ITALY.

  • Premium

    Mercury monitoring for isotopic abundance by the ICP-MS

    Studies of real-world ecosystems are very complex. Mercury species inter-conversion as well as mercury deposition and evasion are constantly occurring. One technique to help sort out the processes is to trace reactions using natural Hg isotopes. Either by enriching a system with a particular isotope or determination of isotopic ratios as a technique of source identification, isotopes are a powerful tool for investigation. The Tekran 2600 Total Mercury and Tekran 2700 Methyl Mercury systems are designed to couple to an ICP-MS for mercury quantification by CVAFS and isotopic abundance by the ICP-MS.

    By Tekran Instruments Corporation based in Toronto, ONTARIO (CANADA).

  • Environmental monitoring solution for power plant

    The construction of coal and natural gas power stations is continuing at a steady rate along with older power stations being retrofitted with more effective flue gas cleaning systems. Both the community and environmental protection authorities are paying closer attention to both emission and ambient concentrations around power stations.

    By Ecotech Pty Ltd based in Knoxfield, AUSTRALIA.

  • Airport Environmental Monitoring

    Water pollution from airport run-off is increasingly coming under public and government scrutiny. As environmental regulations tighten, the ability to monitor for aviation fuel contamination from runway run-off has become essential.

    Monitoring sites at airports can be extremely challenging often with no power or telephone lines available and with limited access for maintenance. Chelsea’s robust UviLux Hydrocarbon Sensor with its low power consumption and high accuracy is ideally suited for this application. Installed at various locations around the airport, deployed with it’s own integrated anti-biofouling system, utilising the GSM network, the monitoring sites send data to a secure ftp site, where any internet enabled device can access the data. In this way the systems act as any early warning system allowing any hydrocarbon discharge to be detected in real-time.

    Optional environmental monitoring features include remote control to allow the user to turn equipment on and off, change the sample rate and detection range. There is also a facility to allow SMS text and email alarm notifications triggered by user-defined set-points together with customised web pages, data displays and automated data downloads via an ftp server.

    Airport runoff can contain high concentrations of various pollutants, in particular polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs), the environmental levels of which have to be monitored. An understanding of the magnitude of contamination due to airport runoff water is important for the effective management of airport infrastructure. Chelsea’s robust UviLux Hydrocarbon Sensor with its low power consumption and high accuracy is ideally suited to the airport environment.

    By Chelsea Technologies Group based in West Molesey, UNITED KINGDOM.

  • Premium

    Water monitoring technology for urban hydrology

    Urban Hydrology deals with the specific aspects of the hydrological cycle in urban and industrial settings. This includes all natural water flows as well as the consideration of precipitation, storm water, groundwater, rivers, and lakes, but also the infrastructure and systems for water supply and sanitation in a city.

    By OTT Hydromet - a member of Hach Company based in Kempten, GERMANY.

  • WS200 Weather Station Data Management

    The new WS200 is a reliable and cost efficient Windows® based data management system for controlling, monitoring, automatic collection, and data transmission of metrological and hydrological networks.

    By Felix Technology Inc. based in Concord, ONTARIO (CANADA).

  • Filtration for Flue Gas Analysis and CEMS

    Three Steps of CEMS: 1st Step: Gas Sampling 2nd Step: Gas conditioning and treatment 3rd Step: Measurement/Calibration In first step, the function is to get sample gas and forward to 2nd step for treatment. During this step, it cannot block the probes and cannot result condensation of moisture. So a filter online back flushing should be equipped in this part. The filters to be used: 1, Filter is used to ensure the stability of system and reduce the maintenance 2, Filtration Grade: usually 2 or 3 micron 3, Temp. is around 0-180 deg C 4, Back flushing gas is heated, impulse flushing 5, Filter Material: Titanium Sintered, SS316L Sintered, PTFE sintered, Ceramic Membrane and so on 2nd Step Gas Treatment: #11;The coarse filters and the liquid particle filters The coarse and fine cartridge can filter the small particles in the gas and acid aerosol things to better protect the instruments. The micron can be 0.1micron, filtration rate can be up to 99.99%, two layers can be 99.9999%

    By Shanghai CMI Environmental Technology Co.,Ltd. based in Shanghai , CHINA.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you