Only show results available in Virginia? Ok

flow calibrator Applications

  • Continuous Emissions Monitoring Calibration Systems (CEMCS)

    The Environics Series Continuous Emissions Monitoring Calibration Systems (CEMCS) have been used in CEM vans and laboratories for over twenty years. They meet or exceed the performance requirements of the United States EPA 40 CFR Part 51 Method 205 Appendix M. Our systems are custom built, computerized, mass flow controller based gas calibration systems which allow you to dilute a single high concentration cylinder of span gas to low levels for the calibration of gas analyzers.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Computerized instrumentation for the medical gas flow and scientific research

    Environics gas mixing, blending and dilution systems provide for precise mixing of gases for a wide variety of clinical applications. Our systems can produce gas concentrations from percent to ppb levels for single or multi-point calibration. The high accuracy of our mixers make them the units of choice for a wide variety of laboratory and research applications. For example, Environics Biological Atmosphere Incubation Mixers provide stable and accurate gas mixes for any laboratory or clinical need. You can generate the specific reduced oxygen environments needed for anerobes as well as the enriched oxygen environments needed in a variety of cellular, viral and high density culture applications. Systems can also be used to create a specific and stable gaseous environment in a clean room. In all cases, the Environics Atmosphere Mixers allow you to use less expensive single-gas cylinders or bulk tanks in place of a high number of expensive blended cylinders.

    By Environics, Inc. based in Tolland, CONNECTICUT (USA).

  • Premium

    Testing Fume Hood Flow Dynamics using SF6 as a Tracer Gas

    A safe laboratory environment requires an effective method for clearing toxic material from fume hoods. Since all handling of toxic materials is completed in these hoods, it is critical to have a procedure to evaluate their operation to assure adequate protection for laboratory workers. The InfraRan Specific Vapor Analyzer, factory calibrated for SF6, is an ideal instrument for measuring fume hood efficiency in accordance with ASHRAE and other standards. Manufacturers identify the flow dynamics (factors that affect air flow in the hood and performance with air) using the ratings AM (as manufactured), AI (as installed), and AU (as used). A fume hood evaluation conducted under its operational environment is critical, as these tests will indicate any installation shortcomings as well as direct workers in proper laboratory hood techniques.

    By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA).

  • Premium

    Water Vapor Permeation Analyzers for Packaging Industry

    For packaging film barriers, the Systech Illinois range of water vapor permeation analyzers offer a wide measurement range with precision temperature, humidity and flow control. These analyzers utilise the Coulometric P2O5 sensor, which is more sensitive and stable than infra-red and does not require calibration. The P2O5 is the primary method for absolute moisture measurement.

    By Systech Instruments Ltd based in Thame, UNITED KINGDOM.

  • Premium

    Capabilities of the Adsorbent Tube Injector System (ATIS™)

    The Adsorbent Tube Injector System (ATIS) was developed at Supelco® by R&D Scientists, as a tool to assist in our comprehensive adsorbent research for thermal desorption tubes. The ATIS provides an efficient means of transferring calibration standards in either the gas or liquid phase onto the adsorbent packed tubes. The ATIS employs the technique of flash vaporization to vaporize the sample in a continuous flow of inert gas; the inert gas carries the sample to the tube. The sample pathway of the ATIS is constructed of glass and stainless steel. The calibration standard is injected by a syringe through a replaceable septum in the center of the injection glassware, which is heated. After enough time has elapsed, typically less than five minutes, the tube is removed from the ATIS and analyzed using the appropriate analytical technique for that adsorbent tube.

    By Sigma-Aldrich Co., LLC based in Bellefonte, PENNSYLVANIA (USA).

  • Premium

    Gas analysis & monitoring system for gas generation

    The gas generators for calibration based on the use of “Method of Permeation Tubes.”. The permeation tubes are sealed capsules containing a small amount of the component that is in contact with a permeable membrane stable. The permeation through the membrane produces a vapor of the compound of the component of small quantity, very stable as a stream in time. This permeate stream by mixing with a dilution gas controlled and precise (for example nitrogen) creates a mixture in track at the desired concentration. The flow of the permeate is measured metrically through severe weight loss of the tube thus ensuring a standard high precision.

    By ETG Risorse e Tecnologia based in Montiglio, ITALY.

  • OneRainware™ - Radar rainfall for real-time and analytical applications.

    Accurate estimation of the spatial distribution of rainfall is critical to successfully model hydrologic processes. OneRain has worked with engineering firms and those with responsibilities in Stormwater and Wastewater Management across the U.S. to provide radar rainfall data to help characterize storm events or flow problems in collection systems and as a basis for both real-time and design-oriented modeling. OneRainware products and services offer: *Real-time gauge-adjusted radar rainfall (GARR) data *Real-time area-average rainfall *Real-time forecast rainfall *End-of-month archive quality gauge-adjusted radar rainfall data *Historical and post-event analysis using archived rainfall estimates *Web-delivered calibrated radar-rainfall data *StormProperties™ Analysis. GARR data are used in flood warning, runoff modeling, basin modeling, I/I studies, litigation, real-time control, design storms, and National Pollutant Discharge Elimination System (NPDES) compliance activities.

    By OneRain Incorporated based in Longmont, COLORADO (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you