Only show results available in Virginia? Ok

ftir sample Applications

  • Premium

    Measurement solution for FTIR Vs. GC in gas analysis

    Comparison of Technologies

    A gas chromatograph (GC) has traditionally been the technology of choice for laboratory analysis of gas samples. GCs have been used for over 50 years in the qualification and quantification of complex mixtures of gases. The techniques and methodology required to run GCs are often a pre-requisite for any laboratory technician. Recent developments in Fourier Transform Infra-Red (FTIR) gas analysis has enabled this technology to start to replace GCs in the lab.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Measurement solution for multi-stream combustion research

    Protea supplied a complete turn-key measuring system for multi-point sampling in a University combustion research laboratory. Utilising the latest in FTIR spectroscopy, atmosFIR, a complete cabinet system was supplied containing: atmosFIR FTIR Gas analyser, Sampling System Control Module (SSCM), Heated Stream Selection Module (HSSM), Temperature Control Module (TCM), 4 heated sample lines, 4 heated sample probes, Embedded PC controller.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Monitoring solutions for the continuous emissions monitoring

    Multi-gas Stack Analyzers for Continuous Emissions Monitoring. FTIR and UVDOAS Analyzer Models available for Insitu Probe, Internal or External Cells, or Cross Stack Sample Acquisition.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Perimeter Ambient Air Monitoring

    Cerex Multi-Gas Open Path Analyzers are available in both FTIR and UVDOAS technologies to meet specific requirements for perimeter ambient air quality monitoring, leak detection, fugitive emissions monitoring and ambient air quality monitoring. Cerex multi-gas analyzers offer significant advantages over single gas analyzer arrays, electro-chemical sensor arrays and time integrated air sampling hardware

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Gas monitoring instruments and systems for engine emissions measurements

    The exhaust gas from combustion engines is a complex mixture of gases and particulate matter. The composition of the gas may change rapidly. Multicomponent analysis of exhaust gases can be performed with a Gasmet™ FTIR Gas Analyzer with a response time (T90) of one second. The winning combination is the result using of a small volume gas sample cell, a powerful sample pump and a fast detector with liquid nitrogen cooling. The analyzer, sampling system and computer can be assembled on a cart for use in a dynamometer laboratory, or the portable version can be used for roadside tests.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Gas monitoring instruments and systems for process NOx measurement

    Nitric acid HNO3 is an important intermediate reagent for production of several important end products, such as fertilizers, explosives, dyestuffs/pigments, pesticides, pharmaceuticals, photographic materials, plastics, and synthetic fibers. At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement system, and the Gasmet™ FCX Gas Analyzers, both of which utilize the FTIR measurement technique for simultaneous multicomponent analysis of the sample gas.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Analysis of aqueous solutions

    IR-Spectroscopy is not limited to gases, solid materials and pure liquids but also facilitates the measurement of solutes in aqueous media. Though, due to the strong and temperature dependent absorption of water, the usage of conventional IR-transmission and ATR accessories is not very suitable for the analysis in water. The CONFOCHECK is a dedicated FT-IR system for the fast, easy and sensitive analysis of aqueous samples. Using this system, preparing, measuring and evaluating any aqueous sample takes typically about 1 minute.

    By Bruker Corporation based in Billerica, MASSACHUSETTS (USA).

  • X-ray fluorescence XRF analysis for environmental protection and waste management

    To meet the requirements of new regulations and to protect the environment effectively, industries need techniques that enable the analysis of elements at lowest concentration levels. Bruker X-ray fluorescence (XRF) analysis is the most suitable analytical technique for handling different kinds of materials. Bruker’s XRF, ICP-MS, GC, TOF-MS, FT-IR, CBRNE products and applications help you to monitor contaminated land efficiently and quickly, to determine hazardous elements in the air and water, as well as to classify waste material and to specify products for recycling and disposal. Whether solids, sludge, filters, liquids or powders: there is a fast and simple sample preparation technique for every material type.

    By Bruker Corporation based in Billerica, MASSACHUSETTS (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you